|
|
楼主 |
发表于 2009-6-27 09:25:06
|
显示全部楼层
Config serial console: ttyS0,115200
Auto Detection OHIO chip
This SOC has MDIX cababilities on chip.
WLAN 1350 chip configured.
vlynq_polarity = low
Success in setting up the VLYNQ.
CPU revision is: 00018448
Primary instruction cache 16kb, linesize 16 bytes (4 ways)
Primary data cache 8kb, linesize 16 bytes (4 ways)
Number of TLB entries 16.
Linux version 2.4.17_mvl21-malta-mips_fp_le (root@localhost.localdomain) (gcc ve
rsion 2.95.3 20010315 (release/MontaVista)) #3 Wed Jan 10 18:32:13 CST 2007
Determined physical RAM map:
memory: 14000000 @ 00000000 (reserved)
memory: 00020000 @ 14000000 (ROM data)
memory: 00fe0000 @ 14020000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line:
calculating r4koff... 00102c00(1059840)
CPU frequency 211.97 MHz
Calibrating delay loop... 211.35 BogoMIPS
Freeing Adam2 reserved memory [0x14001000,0x0001f000]
Memory: 14260k/16384k available (1606k kernel code, 2124k reserved, 103k data, 6
0k init)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
TI Optimizations: Allocating TI-Cached Memory Pool.
Warning: Number of buffers is not configured.Setting default to 120
Using 120 Buffers for TI-Cached Memory Pool.
DEBUG: Using Hybrid Mode.
NSP Optimizations: Succesfully allocated TI-Cached Memory Pool.
Initializing RT netlink socket
DEBUG: Starting ksoftirqd with ALWAYS_SOFTIRQ:0x3 NON ALWAYS SOFTIRQ:0xfffffffc.
DEBUG: Starting ksoftirqd with priority:0 policy:0 nice:19.
Starting kswapd
Disabling the Out Of Memory Killer
devfs: v1.7 (20011216) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
pty: 32 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0xa8610e00 (irq = 15) is a 16550A
Installed misc driver vlynq0: it handles vlynq bridge0 with 1 hop(s).
block: 64 slots per queue, batch=16
Initializing the TI QoS NSP Framework.
DEBUG: Initializing the Network Queue Manager Algorithms.
DEBUG: Initialization of the Translation Unit.
DEBUG: Initializing the LOCAL High Priority Database Module.
DEBUG: Initialization of the LOCAL High Priority Database Module successful..
Succesfully Initialized the TI QoS NSP Framework.
Error getting CPMAC Configuration params for instance:0
Environment Variable:MACCFG_A not set in bootloader
Setting Default configuration params for CPMAC instance:0
MAC CFG : Tx Interrupts off , threshold : 20
Default Asymmetric MTU for eth0 1500
Default Asymmetric MTU for eth1 1500
CPMAC: Registered switch port 1 with device eth1
Default Asymmetric MTU for eth2 1500
CPMAC: Registered switch port 2 with device eth2
Default Asymmetric MTU for eth3 1500
CPMAC: Registered switch port 3 with device eth3
TI CPMAC Linux DDA version 1.9 - CPMAC DDC version 0.3
Cpmac: Installed 1 instances.
Cpmac driver is allocating buffer memory at init time.
PPP generic driver version 2.4.1
avalanche flash device: 0x800000 at 0x10000000.
Try Determine FLASH TYPE
CHIP Manufacturer's ID=BF Device ID=236D
Found SSTV39VF640XB FLASH
Number of erase regions: 2
Primary Vendor Command Set: 0002 (AMD/Fujitsu Standard)
No Primary Algorithm Table
Alternative Vendor Command Set: 0000 (None)
No Alternate Algorithm Table
Vcc Minimum: 2.7 V
Vcc Maximum: 3.6 V
No Vpp line
Typical byte/word write timeout: 8 磗
Maximum byte/word write timeout: 16 磗
Full buffer write not supported
Typical block erase timeout: 16 磗
Maximum block erase timeout: 32 磗
Typical chip erase timeout: 32 磗
Maximum chip erase timeout: 64 磗
Device size: 0x800000 bytes (8 MiB)
Flash Device Interface description: 0x0001
- x16-only asynchronous interface
Max. bytes in buffer write: 0x1
Number of Erase Block Regions: 2
Erase Region #0: BlockSize 0x1000 bytes, 2048 blocks
Erase Region #1: BlockSize 0x10000 bytes, 128 blocks
Amd/Fujitsu Extended Query Table v |
|
粤公网安备44152102000001号 
发表于 2009-6-27 09:15:51