这猫没啥可玩
HI, BSBC
P:3101
P:1013
P:1018
P:3202
P:3203
P:3204
P:1021
Start in Safetycode
chip up mode is 3
VSIN0: 4(0x385)
VSIN1: 7(0x5b6)
Hard rst reason:0x42
Will init calibrate...
RF init
Spi init success
Wifi rf2(6W25) calibrate success
Wifi rf0(6W22) calibrate success
End out Safetycode
BL2
DDR4 F4
Start in Startcode 2022.07
Starting slave core
S
DDRs
startcode uboot boot count:0
Start in Safe Mode
hash_cal.size:0x7d000
ipsec register chip 0x15
Use the AllsytemA to load success
End out startcode
Start in U-boot
Start in U-boot
NAND: SPI NAND FLASH TYPE
flash_type = [0x0]
Special Nand id table Version 1.23
Nand ID: 0xEF 0xAA 0x22 0x00 0x00 0x00 0x00 0x00
now using default nand flash type, Block:128KB Page:2KB!
Use Compatibility flash solution!
ECC Match pagesize:2K, oobzie:64, ecctype:16bit,mtd->size:0x0
Nand(Hardware): Block:128KB Page:2KB Chip:268435456B OOB:64B ECC:16bit
256 MiB
256 MiB
Loading Environment from <NULL>...
OK
[UBI-DEBUG]: all in ubi mode
In: serial
Out: serial
Err: serial
Net: PHY power down !!!
Boot cfg head magic1:0xffffffff, magic2:0xffffffff
Init boot config success.
[mem test]
Not found mem test flag
No need to make ram test
[mbist test]
Not found mbist test flag
No need to make mbist test
[ssn test]
Not found ssn test flag
No need to make ssn test
[greenbox test]
Not found greenbox test flag
No need to make greenbox test
[exmbist test]
Not found exmbist test flag
No need to make exmbist test
FastMap Enable:false
ubi0: default fastmap pool size: 100
ubi0: default fastmap WL pool size: 50
UBI: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "ubifs", size 255 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 2033, bad PEBs: 7, corrupted PEBs: 0
ubi0: user volume: 13, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 47/10, WL threshold: 4096, image sequence number: 725363946
ubi0: available PEBs: 24, total reserved PEBs: 2009, PEBs reserved for bad PEB handling: 33
Start from main system(0x0)!
CRC:0x3d80a8b4, Magic1:0x5a5a5a5a, Magic2:0xa5a5a5a5, count:1, CommitedArea:0x0, Active:0x0, RunFlag:0x0
close uboot pcie
Main area: Cert partition Found
Slave area: Cert partition Found
Last start status:
0x00000000 0x00000000 0x00000000 0x00000008 0x00000004
0x00000000 0x0000000c 0x00000000 0x00000000 0x00000000
0x00000000 0x00000000 0x00000000 0x00000004 0x00004000
0x00000000 0x00000000 0x00000000 0x00000020 0x00000000
Main area (A) is OK!
CRC:0x93e83925, Magic1:0x5a5a5a5a, Magic2:0xa5a5a5a5, count:1, CommitedArea:0x0, Active:0x0, RunFlag:0x0
boardconfig start
Real boardID:9, SoCName:HWSOC12
Match boardID:9, SoCName:HWSOC12
NP reserve ram size:0x51
Set avs pwm<29> success.
Set avs pwm<20> success.
Set cpu freq<1100M> success.
real_ddr_size: 1073741824/1024M
uncrypt part, part_index=7
<lanfeng-debug>Fun:passwd_abort_key, Line249
Match the dtb file index : 15!
Use flash decoupling solution
XIP Kernel Image
End out U-boot
Uncompressing... done, booting...
Slave released
[ 0.019258] OF: amba_device_add() failed (-2) for /sysctl@10100000
[ 0.021323] OF: /uart1@0x10119000: could not find phandle
[ 0.021686] OF: amba_device_add() failed (-2) for /system-controller@10100000
[ 0.053536] OF: amba_device_add() failed (-2) for /sysctl@10100000
[ 0.060014] OF: amba_device_add() failed (-2) for /system-controller@10100000
[ 0.214250] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.660712] **** Total Boot time: 1660 ms, uncompress initrd cost 0 ms ****
enter rc.ttyinit................
out rc.ttyinit................
|
粤公网安备44152102000001号 
发表于 2025-5-26 22:21:02