改天我也要试试看。 看了 只能看懂几个，10.3的CFE系通过刷哪个固件刷上去的？ 纯支持啊
RE: [BCM6358]大亚DB120-WG的折腾从BCM公版-OPENWRT-电信E家
继续刷刷刷：OPENWRT Backfire 10.03 内测版（5月5日发布，OPENWRT中文论坛有针对DB120和RG100A的2个版本，文件大小： 11.38M）再次说明，至今为止的OPENWRT 系统暂不支持内置ADSL，必须外接猫当普通路由器用（当然是功能强大的路由器），LAN4 为WAN 接入，LAN1-3 为普通网口。
还是在CFE 1.0.37-10.3 的状态下，进入CFE>，在192.168.1.1的页面 刷新固件，OPENWRT 固件刷一次即可（因为固件文件较大，时间会稍长），重启就能登录192.168.1.1 用户名 root 密码 admin
指示灯状态：电源 绿，DSL 与INTERNET 不亮（拨号成功了也不亮），LAN1-3正常，LAN4 不亮，无线灯不亮，USB 灯常亮。这一点不太方便。
直接在WAN 设置里把ADSL 账号密码输入，有绑定MAC 的，直接输入绑定的MAC ，保存并应用就行了，本人用快速设置过几次，老是拨不了号，后来恢复出厂设置（捅RESET键）后，在WAN 设置就能上网了，LAN 一般不用设置，开启无线等设置都很简单。
很多高级功能的，慢慢研究吧。
RE: [BCM6358]大亚DB120-WG的折腾从BCM公版-OPENWRT backfire 10.03
附一个backfire 10.03 的TTL 启动信息：没有连接相关的信息，只能在WEB界面的“状态”-“系统日志”下查看。
CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: 二1月 29 07:41:15 CST 2008 (root@ZTJ)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot Kern
AuxFS Misc PSI
Flash RootFS Partition Length: 12320768
100 MB Full-Duplex (auto-neg)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x805285A0 (1209760)
Initialized Data: 0x8041DD30 - 0x8041FDC0 (8336)
BSS Area: 0x8041FDC0 - 0x804265A0 (26592)
Local Heap: 0x804265A0 - 0x805265A0 (1048576)
Stack Area: 0x805265A0 - 0x805285A0 (8192)
Text (code) segment: 0x80401000 - 0x8041DD30 (118064)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.159
Gateway IP address :
Run from flash/host (f/h) : h
Default host run file name : 308nfs6358
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-9) : 96358VW2
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:12:34:56:78:90
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xbe020000) ...
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.32.10 (openwrtcn@ip-10-242-58-208) (gcc version 4.3.3 (GCC) ) #10 Tue May 4 22:51:39 EDT 2010
Detected Broadcom 0x6358 CPU revision a1
CPU frequency is 300 MHz
32MB of RAM installed
registering 40 GPIOs
board_bcm963xx: CFE version: 1.0.37-10.3
bootconsole enabled
CPU revision is: 0002a010 (Broadcom BCM6358)
board_bcm963xx: board name: 96358VW2
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map active PFN ranges
0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 32kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Memory: 29680k/32768k available (2096k kernel code, 3088k reserved, 365k data, 136k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 299.00 BogoMIPS (lpj=598016)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Success to register irq 35 for button reset.
Create /proc/button_reset success.
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(0.295:1): initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)漏 2001-2006 Red Hat, Inc.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
蔯onsole enabled, bootconsole disabled= 10) is a bcm63xx_uart
console enabled, bootconsole disabled
bcm963xx_flash: Flash phys=0x1e000000, size=0x02000000, virt= 0xbe000000
Number of erase regions: 1
Primary Vendor Command Set: 0002 (AMD/Fujitsu Standard)
Primary Algorithm Table at 0040
Alternative Vendor Command Set: 0000 (None)
No Alternate Algorithm Table
Vcc Minimum:2.7 V
Vcc Maximum:3.6 V
No Vpp line
Typical byte/word write timeout: 64 碌s
Maximum byte/word write timeout: 512 碌s
Typical full buffer write timeout: 64 碌s
Maximum full buffer write timeout: 2048 碌s
Typical block erase timeout: 512 ms
Maximum block erase timeout: 4096 ms
Typical chip erase timeout: 524288 ms
Maximum chip erase timeout: 2097152 ms
Device size: 0x1000000 bytes (16 MiB)
Flash Device Interface description: 0x0002
- supports x8 and x16 via BYTE# with asynchronous interface
Max. bytes in buffer write: 0x40
Number of Erase Block Regions: 1
Erase Region #0: BlockSize 0x20000 bytes, 128 blocks
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
bootloc=5, NumEraseRegions=1.
bcm963xx: CFI does not contain boot bank location. Assuming top.
cfi->addr_unlock1 = 0x555, cfi->addr_unlock2 = 0x2aa
number of CFI chips: 1
0: offset=0x0,size=0x0,blocks=131072
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6 and board type 96358VW2
bcm963xx_flash: Partition 0 is CFE offset 0 and length 20000
bcm963xx_flash: Partition 1 is kernel offset 20100 and length dff00
bcm963xx_flash: Partition 2 is rootfs offset 100000 and length ee0000
bcm963xx_flash: Partition 3 is nvram offset fe0000 and length 20000
bcm963xx_flash: Partition 4 is linux offset 20000 and length fc0000
bcm963xx_flash: Spare partition is b80000 offset and length 460000
Creating 5 MTD partitions on "bcm963xx":
0x000000000000-0x000000020000 : "CFE"
0x000000020100-0x000000100000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x000000100000-0x000000fe0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=B80000, len=460000
0x000000b80000-0x000000fe0000 : "rootfs_data"
0x000000fe0000-0x000001000000 : "nvram"
0x000000020000-0x000000fe0000 : "linux"
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: adsl
Registered led device: ppp-fail
Registered led device: power
Registered led device: stop
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 136k freed
Please be patient, while OpenWrt loads ...
- preinit -
Press the key and hit to enter failsafe mode
- regular preinit -
switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
- init -
Please press Enter to activate this console. bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1
bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1
PPP generic driver version 2.4.2
NET: Registered protocol family 24
eth0: link UP - 100/full - flow control off
eth1: link forced UP - 100/full - flow control off/off
device eth1 entered promiscuous mode
br-lan: port 1(eth1) entering forwarding state
Generic kernel compatibility enabled based on linux-next next-20100113
cfg80211: Calling CRDA to update world regulatory domain
SCSI subsystem initialized
roboswitch: Probing device eth0: Failed to enable switch
roboswitch: Probing device eth1: found a 5325! It's a 5350.
eth0: link DOWN
cfg80211: World regulatory domain updated:
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
eth0: link UP - 100/full - flow control off
usbcore: registered new device driver usb
b43-phy0: Broadcom 4318 WLAN found (core revision 9)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
NTFS driver 2.1.29 .
ip_tables: (C) 2000-2006 Netfilter Core Team
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
nf_conntrack version 0.5.0 (465 buckets, 1860 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
IMQ driver loaded successfully.
Hooking IMQ before NAT on PREROUTING.
Hooking IMQ after NAT on POSTROUTING.
xt_time: kernel timezone is -0000
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
fuse init (API version 7.13)
b43 ssb0:0: firmware: requesting b43/ucode5.fw
b43 ssb0:0: firmware: requesting b43/pcm5.fw
b43 ssb0:0: firmware: requesting b43/b0g0initvals5.fw
b43 ssb0:0: firmware: requesting b43/b0g0bsinitvals5.fw
b43-phy0: Loading firmware version 478.104 (2008-07-01 00:50:23)
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
-------------系统日志-----------------
May5 10:53:15 OpenWrt daemon.info pppd: Plugin rp-pppoe.so loaded.
May5 10:53:15 OpenWrt daemon.notice pppd: pppd 2.4.4 started by root, uid 0
May5 10:53:15 OpenWrt daemon.info pppd: PPP session is 8438
May5 10:53:15 OpenWrt daemon.info pppd: Using interface ppp0
May5 10:53:15 OpenWrt daemon.notice pppd: Connect: ppp0 <--> eth0
May5 10:53:16 OpenWrt daemon.info dnsmasq: exiting on receipt of SIGTERM
May5 10:53:16 OpenWrt user.info kernel: eth0: link UP - 100/full - flow control off
May5 10:53:18 OpenWrt daemon.info pppd: CHAP authentication succeeded: Authentication success,Welcome!
May5 10:53:18 OpenWrt daemon.notice pppd: CHAP authentication succeeded
May5 10:53:18 OpenWrt daemon.notice pppd: peer from calling number 00:18:82:0B:61:10 authorized
May5 10:53:18 OpenWrt daemon.notice pppd: localIP address 110.*.*.*（本人隐藏）
May5 10:53:18 OpenWrt daemon.notice pppd: remote IP address 110.*.*.1（本人隐藏）
May5 10:53:18 OpenWrt daemon.notice pppd: primary DNS address 58.20.127.170
May5 10:53:18 OpenWrt daemon.notice pppd: secondary DNS address 58.20.127.238
May5 10:53:19 OpenWrt daemon.info dnsmasq: started, version 2.52 cachesize 150
May5 10:53:19 OpenWrt daemon.info dnsmasq: compile time options: IPv6 GNU-getopt no-DBus no-I18N DHCP TFTP
May5 10:53:19 OpenWrt daemon.info dnsmasq-dhcp: DHCP, IP range 192.168.1.100 -- 192.168.1.250, lease time 12h
May5 10:53:19 OpenWrt daemon.info dnsmasq: using local addresses only for domain lan
May5 10:53:19 OpenWrt daemon.info dnsmasq: reading /tmp/resolv.conf.auto
May5 10:53:19 OpenWrt daemon.info dnsmasq: using nameserver 58.20.127.238#53
May5 10:53:19 OpenWrt daemon.info dnsmasq: using nameserver 58.20.127.170#53
May5 10:53:19 OpenWrt daemon.info dnsmasq: using local addresses only for domain lan
May5 10:53:19 OpenWrt daemon.info dnsmasq: read /etc/hosts - 1 addresses
May5 10:53:19 OpenWrt daemon.info dnsmasq-dhcp: read /etc/ethers - 0 addresses
May5 10:53:22 OpenWrt user.notice root: starting ntpclient
May5 10:53:22 OpenWrt user.notice rdate: No usable time server found
楼主果然厉害啊，是不是联通红版的lan4口都不能用啊？我一直纳闷这个问题，谢谢啦。 LAN4 为WAN 接入，LAN1-3 为普通网口。[/quote]
lz我有两根adsl,一根电话线进adsl口,另一根连个猫再连到LAN4口,行不行啊,你说刷那种版本最好 能用来刷hg522 c吗？