我的H608B没救了?
我的H608B外置天线的,一直用的还行.昨天不知道为什么开关了下猫的电源就再也上不去网了.现在的情况是:POWER灯常亮,RUN灯闪,LAN灯亮,唯独DSL灯不亮了,DSL只是闪几下就灭了.并且也PING不通192.168.1.1 配置界面自然也登陆不了.
各位高手看看我这猫还有救吗?如果刷机能救回来的话用什么方法?一直也没找到刷机的方法和相关工具
谢谢啦~ 换个猫试试看能正常吗？dsl灯不常亮的话表示电话线路的adsl信号没有同步。有可能是线路问题也有可能是设备故障，所以要排除清楚先。 线路没有问题,现在就在用5年前的阿尔卡特老猫+DI-504在上网求救~ FSB v0.06 PLL w ln p08 zi
ZXV10 HGW bootloader V1.9
SDRAM size = 0x2000000-------->
Hardware version is 1-------->
Processor clock speed 264.0MHz
FLASH size = 0x1000000-------->
Finding flashfs partition ...@ offset 00540000
Finding flashfs partition ...@ offset 00620000
2 partition found
Boot from image A @ offset 00540000
done.
Image 'image' is a Linux kernel
Trying to load initrd...none found
Calling Configure_NVS_FromFile.
LZMA 4.05
00bXLinux version 2.6.11.12 (xia@localhost.localdomain) (gcc version 4.0.1) #138
Wed Aug 20 14:03:53 CST 2008
CPU: ARM1026EJ-Sid(wb)B revision 2 (ARMv5TEJ)
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets
Machine: Solos CX46xx, unknown variant
!!!!!!!
the hw id is 1,
!!!!!!Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists
Kernel command line: console=ttyS0 root=31:4 rw mem=31M mtdparts=phys_mapped_fla
sh:256k(boot),1024k(kernel),4992k(JFFS2),1024k(k2),4992k(J2),-(CT) rootfstype=jf
fs2
init_dma not supported
PID hash table entries: 128 (order: 7, 2048 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 31MB = 31MB total
Memory: 28980KB available (1959K code, 379K data, 76K init)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new driver hub
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
Ledkey Driver Version 0.0.1.
ledkey : ===== ledkey_init =====
init watchdog!!!
zteinfo_init
Solos on-chip UART init.
ttyS0 at I/O 0x0 (irq = 29) is a Solos UART
io scheduler noop registered
RTL18305SD: Registered new driver
PPP generic driver version 2.4.2
NET: Registered protocol family 24
physmap flash device: 1000000 at 38000000
phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
phys_mapped_flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 8 MTD partitions on "phys_mapped_flash":
0x00000000-0x01000000 : "flash"
0x00000000-0x00020000 : "Bootloader"
0x00020000-0x00040000 : "config"
0x00540000-0x00620000 : "kernel"
0x00040000-0x00540000 : "filesystem"
0x00620000-0x00700000 : "kernel2"
0x00700000-0x00c00000 : "filesystem2"
0x00c00000-0x01000000 : "ct-jffs2"
Solos-W EHCI starting up...
solosW-ehci usb00: Solos USB 2.0
solosW-ehci usb00: irq 9, pci mem ff800100
solosW-ehci usb00: new USB bus registered, assigned bus number 1
wlan short push
solosW-ehci usb00: park 0
solosW-ehci usb00: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
usb usb1: Product: Solos USB 2.0
usb usb1: Manufacturer: Linux 2.6.11.12 ehci_hcd
usb usb1: SerialNumber: Solos EHCI
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
INTR_MASK 37, 37
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
u32 classifier
OLD policer on
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
IPv4 over IPv4 tunneling driver
ip_conntrack version 2.1 (248 buckets, 1984 max) - 320 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack_rtsp v0.01 loading
ip_nat_rtsp v0.01 loading
netfilter PSD loaded - (c) astaro AG
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Please set the MAC Address for the WAN Bridge.
Set the Environment variable 'wan_br_mac'.
MAC Address should be in the following format: xx.xx.xx.xx.xx.xx
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 76K
init started:BusyBox v1.01 (2008.08.20-06:05+0000) multi-call binary
Starting pid 136, console /dev/ttyS0: '/etc/rc'
Alarm clock
Loading Conexant BSP...
Using /lib/modules/2.6.11.12/kernel/drivers/net/arm/solos_ethernet.ko
solos_ethernet: module license 'unspecified' taints kernel.
rtl8306sd_hw_init
rtl8306_switch_init
rtl8306_initsucess!
rtl8306_initQossucess!
rtl8306_setCPUPortsucess!
rtl8306_initVlansucess!
rtl8306 IGMP snooping enabled!
rtl8306sd_hw_init
rtl8306sd_hw_init
rtl8306sd_hw_init
rtl8306sd_hw_init
rtl8306sd_hw_init
rtl8306sd_hw_init
solos_eth_mii: probed
Using /lib/hsl_mod_gpl.o
Using /lib/cnxt_fiq.o
Using /lib/cnxt_drv.o
BASE MAC ADDRESS 00:11:22:33:44:55
Starting Conexant drivers
.
Quantum v1.01
msc16 loaded
'create dev file with mknod /dev/adet_char c 244 0'.
wlan long push
msc16_load_file returned 0
sram_buffer : 0xffa00258 addr : 0x70000258
Passing command buffer 70000258 to MSC16
Conexant drivers started
starting task turbo_WhipTask
DSL MSC16 imem 4096, dmem 2048
DSL MSC16 version 1.3
Using /lib/wlan_wsc.ko
Using /lib/modules/2.6.11.12/kerRUNNING Timer started
nel/arch/arm/mach-solos/solosw_defaultrestore.ko
enable virtual port
value is 20001
value is 30002
value is 40004
value is 50008
Loading Wireless ...
chip_id = 1
1
Reading True PDA ...
---dsl is off--
Using /lib/stun_ahb.ko
DRIVER VERSION: 3.0
---dsl is off--
sm_drv_traffice_init called
Received the MAC Address trap
Waiting for message from kernel
init_mac(): 0:1e:73:d1:37:6e
SIOCGIFFLAGS: No such device
received link state trap
SIOCSIFHWADDR: No such device
SIOCGIFFLAGS: No such device
in atm_dev_register, acQosAdslName bunatm
Starting pid 264, console /dev/ttyS0: '/sbin/ge
ZXV10-H608B login: (0x10305) module Enter into qt_register
(0x10306) module Enter
into qr_rule_register
(0x10309) module Enter into qr_type_register
(0x10307) modu
le Enter into qa_register
(0x10308) module Enter into qq_register
MSG(0x003) modul
e proc_msg_init
extract_env_cfg_bin envhdr->magic = ENVZ
extract_env_cfg_bin faile
d! uncompress
envdb-enable =
---dsl is off-- 回车 就出现
ZXV10-H608B login:
ZXV10-H608B login:
ZXV10-H608B login:
ZXV10-H608B login:
ZXV10-H608B login: 高手给看看 是硬件坏了吗? 以上是用TTL线连上超级终端后 开猫的电源出来的信息
但是刚通电回车没反应,信息读完了回车就是
ZXV10-H608B login:
目前就是ping 不通猫 DSL灯不亮 LAN灯亮 RUN灯闪 自己乱折腾弄出个这个页面~~无语了我去哪找image文件啊 愁死我了~
能够进到#号 输入IFCONFIG我也弄不明白现在猫的IP到底是多少了
ZXV10-H608B login: root
Password:
Jan1 00:00:56 login: root loginon `ttyS0'
BusyBox v1.01 (2008.08.20-06:05+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
# ifconfig
eth0 Link encap:EthernetHWaddr 00:1E:73:D1:37:6E
UP BROADCAST MULTICASTMTU:1500Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B)TX bytes:0 (0.0 B)
Interrupt:7 Base address:0x400
eth1 Link encap:EthernetHWaddr 00:1E:73:D1:37:6E
UP BROADCAST MULTICASTMTU:1500Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B)TX bytes:0 (0.0 B)
Interrupt:7 Base address:0x400
eth2 Link encap:EthernetHWaddr 00:1E:73:D1:37:6E
UP BROADCAST MULTICASTMTU:1500Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B)TX bytes:0 (0.0 B)
Interrupt:7 Base address:0x400
eth3 Link encap:EthernetHWaddr 00:1E:73:D1:37:6E
UP BROADCAST MULTICASTMTU:1500Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B)TX bytes:0 (0.0 B)
Interrupt:7 Base address:0x400
lo Link encap:Local Loopback
inet addr:127.0.0.1Mask:255.0.0.0
UP LOOPBACK RUNNINGMTU:16436Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B)TX bytes:0 (0.0 B)
wifi0 Link encap:EthernetHWaddr 00:15:EB:00:00:02
UP BROADCAST RUNNING MULTICASTMTU:1500Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B)TX bytes:0 (0.0 B)
# 我的H608B外置天线的,一直用的还行.昨天不知道为什么开关了下猫的电源就再也上不去网了.
现在的情况是: ...
arwenvc 发表于 2010-1-28 06:52 https://www.chinadsl.net/images/common/back.gif
楼主试试在WebBoot页面下刷这个Linksys的固件能不能认
http://downloads.linksysbycisco.com/downloads/firmware/WAG54G2-EU-AnnexA-ETSI-1.00.17-code.zip
死猫当活猫医了