本帖最后由 piczcn 于 2009-7-27 13:35 编辑
能进cfe界面 就没有砖
Board Id (0-9) : 96358BGWE_OEM1
这个肯定是不对的
e n后改成你刷新固件的borad id （用brfwmod查看固件的信息，根据固件选，而不是选大亚本身的）
有可能就不会不断重启
感谢楼上的 各位，
反正，现在是好用了，
再次谢谢诸位的指点
我也碰到你说的情况，后来也是摸索着试试看更换lan接口，果然成功。祝贺你。
看来还是要买个TTL线才行了。不然刷死就没得救了
TTL哪里有卖的？
LZ你好，我的大亚DB-120也给我刷固件弄得变砖了
刚买了TTL线回来，接上后也能出现启动信息，但是不停地翻滚
CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: Thu Feb 12 13:10:57 CST 2009 (root@localhost.localdomain)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320T, id 0x227a, size 16384KB
Flash Layout: Boot Kern
AuxFS Misc PSI
Flash RootFS Partition Length: 12320768
CFE using EMAC 0
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x805285D0 (1209808)
Initialized Data: 0x8041E210 - 0x8041FDF0 (7136)
BSS Area: 0x8041FDF0 - 0x804265D0 (26592)
Local Heap: 0x804265D0 - 0x805265D0 (1048576)
Stack Area: 0x805265D0 - 0x805285D0 (8192)
Text (code) segment: 0x80401000 - 0x8041E210 (119312)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.159
Gateway IP address :
Run from flash/host (f/h) : h
Default host run file name : 308nfs6358
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-2) : 96358VW2
Number of MAC Addresses (1-32) : 24
Base MAC Address : 00:1e:40:f5:3a:59
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
我按键盘也没反应
不知道你当时是怎么弄好的
能否请你救救急？
QQ： 18894680
感激不尽，还请高人指点
后面还有如下信息是跟楼主不一样的：
Code Address: 0x80010000, Entry Address: 0x80263018
Decompression OK!
Entry at 0x80263018
Closing network.
Starting program at 0x80263018
Linux version 2.6.8.1 (root@linuxserver) (gcc version 3.4.2) #1 Fri Feb 27 16:53:54 HKT 2009
Parallel flash device id 227a is not supported.
Readjusting rootfs partition to block 0 at offset 1107296256
*** Board is not initialized properly ***
prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 4000 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 29376k/32384k available (1948k kernel code, 2964k reserved, 427k data, 80k init, 0k highmem)
Calibrating delay loop... 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...unavailable.
NET: Registered protocol family 16
Computing partition layout for flash of size[-1] sectors[-1]
Flash not used for Auxillary File System
Partition ROOTFS_KRN Blks
SubPartition Image 1 Blks
SubPartition Image 2 Blks
Blk# BlkOff Blks BlkSize AvailSize MemStart MemLen Partition Name
0 1408 -1 -1 -1 0x00000580 1024 BOOTLOADER
-1 0 0 -1 -1 0x00000000 -1 ROOTFS_KRN
-1 0 0 0 0 0x00000000 0 JFFS_AUXFS
-1 0 0 -1 -1 0x00000000 -1 LOG_SCRPAD
-1 4294942719 0 -1 -1 0xffff9fff 24576 PERSISTMEM
No flash for scratch pad!
No flash for log sector!
Can't analyze prologue code at 801f59f4
SCSI subsystem initialized
usbcore: registered new driver hub
Skipping PCI bus scan due to resource conflict
TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca)
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v2.0
Failed to read image tag from flash
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbnet
brcmboard: brcm_board_init entry
ERROR - Invalid number of MAC addresses (1309704800) is configured.
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Cannot open root device "31:0" or unknown-block(31,0)
Please append a correct "root=" boot option
Kernel panic: VFS: Unable to mount root fs on unknown-block(31,0)
<0>Rebooting in 1 seconds..
怎么办？急死了，哪位达人帮忙看看是不是可以修复？
留下名字和脚印，以备需要
你的进入CFE 后按B
重新设置Board ID
ID要对应固件版本~建议你多看成功刷的教程了解下。不过实话告诉你，我看完了刷的一头雾水，最后刷了Dlink-2740BU 2.97
关键还是要自己动手能力和理解能力~