强,不过大家注意,2650U的固件的Board id 为96358VW2
2650BU设备的朋友,没TTL数据线,不要刷哦.呵呵.
还有一点,2650U设备的Flash是8M的,Flash Block是64K的...而国内的2650BU是16M的Flash和Flash Block是128K的... ...
hotqj 发表于 2009-4-8 13:54 https://www.chinadsl.net/images/common/back.gif
期待版主们试试，然后出个教程什么的就好了
有网友在已刷9113的2650BU的基础上升级成功.
等下我就刷进去,试用后再回贴
已经有人刷挂了。
建议没条件的还是不要刷先.
看看，有人成功了吗？
有刷新成功的，但貌似不能连接。。可能是线路不同
看了下usermanual，还是不支持usb存储，和9113没啥区别，不激动
本帖最后由 天涯 于 2009-4-8 20:04 编辑
刷上了,启动信息好下:
接了个256M的FAT32格式的U盘,但不知道如何访问这个U盘.请高手解答.谢谢
CFE version 1.0.37-10.1 for BCM96358 (32bit,SP,BE)
Build Date: Tue Apr 24 15:57:24 CST 2007 (gavin@FD5)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 67108864 bytes (64MB)
Total memory used by CFE:0x80401000 - 0x80527C50 (1207376)
Initialized Data: 0x8041D580 - 0x8041F480 (7936)
BSS Area: 0x8041F480 - 0x80425C50 (26576)
Local Heap: ` 0x80425C50 - 0x80525C50 (1048576)
Stack Area: 0x80525C50 - 0x80527C50 (8192)
Text (code) segment: 0x80401000 - 0x8041D57C (116092)
Boot area (physical): 0x00528000 - 0x00568000
Relocation 芶ctor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 2
Board Id (0-8) : 96358VW2
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:74:04:e4:15:8e
PSI 觟ze (1-64) KBytes : 64
Main Thread Number : 0
*** Pre髎 any key to stop auto run (2 seconds) ***
Auto run second count down: 0
Booting from only image (0xbe800000) ...
Code Address: 0x80010000, Entry Address: 0x80216018
Decompression OK!
Entry at 0x80216018
Closing network.
Starting program at 0x80216018
Linux version 2.6.8.1 (joan@mochow) (gcc version 3.4.2) #1 Tue Mar`31 15:20:17 CS?2009
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 03fa0000 @ 00000000 (usable)
On node 0 totalpages: 16288
DMA zone: 40y6 pages, LIFO batch:1
Normal zone: 12192 pages, LIFO batch:2
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcaghe...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 256 (order 8: 2048 bytes)
Using 150.000 MHz high precision 鬷m錼.
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 62124k/65152k available (1783k kernel code, 2960k reserved, 284k data, 76k init, 0k highmem)
Calibrating delay loop.n. 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...unavailable.
NET: Registered protoc飈 family 16
Total Flash size: 16384K with 128 sectors
File system address: 0xbe800100
Can't analyze prologue code at 801cc474
SCSI subsystem initialized
usbcore: registered new driver hub
Initializing Cryptographic API
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
bc?63xx_mtd driver v1.0
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_鑓d 0000:00:0a.0: irq 18l pci mem c0000300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enable? EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.p (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem ?002400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports det錭ted
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driv錼 usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x3 is enabled
======= GPIO CONFIG_BCM96358 init ========
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xff鎒0120 (irq = 11) is a BCM63XX
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established`4096 bind x192)
Init閍lizing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 76k freed
init started:BusyBox v1.00 (2009.03.31-07:26+0000) multi-鉧ll binary
Algorithmics/MIPS FPU Emulator v1.5
BusyBox v1.00 (2009.03.31-07:26+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
atmapi: mod}le license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
Broadcom BCMPROC芐 v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device ?.3 Mar 31 2009 15:18:26
Config Ethernet Switch Through MDIO Pseudo PHY Interface
dgasp: kerSysRegyste駾yingGasp萢ndler: eth0 registered
eth0: MAC Address: 00:74:04:E4:15:8E
Broadcom BCM6358A1 USB Network Device v0.4 Mar 31 2009 15:18:28
usb0: MAC Address: 00 74 04 E4 15 8F
usb0: Host MAC Address: 00 74 04 E4 15 90
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not de篹cted, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: px776c0000
wl0: MAC Addre髎: 00:74:04:E4:15:91
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.100.27.0.cpe2.1
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
usb 2-1: new full speed USB device using address 2
usb 2-1: not running at`top speed; connect to a high speed hub
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: Dreams Model: Flash Disk Rev: 2.00
Type: Direct-Access ANSI SCSI revision: 02
sda: Unit Not Ready, sense:
Current : sense = 706
ASC=28 ASCQ= 0
Raw sense data:0x70 0x00 0x06 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x28 0x00 0x00 0x00 0x00 0x00
eth0 Link UP.
sda : READ CAPACITY failed.
sda : status=1, message=00, host=0, driver=08
Current sd: sense = 706
ASC=28 ASCQ= 0
Raw sense dataz0x70 0x00 0x06 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x28 0x00 0x00 0x00 0x00 0x00
sda: assuming Write Enabled
sda: assuming drive cache: write through
sda: sda4
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
USB Mass Storage device found at 2
is not de鎍ult cfg.
is not default cfg.
BcmAdsl_Initialize=0xC006A3C8, g_pFnNotifyCallback=0xC0083324
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
pSdramPHY=0xA3FFFFF8, 0x20 0x8088C0
AdslCoreHwReset: AdslOemDataAddr = 0xA3FFB1E4
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 ads?=0x0000p000
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
ATM proc init !!!
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (509 buckets, 0 max) - 376 bytes per conntrack
ip_conntrack_pptp version 2.1 loaded
ip_nat_pptp version 2.0 loaded
ip_ct_h323: init success
ip_nat_h323: init success
ip_conntrack_rtsp v0.01 l颽ding
ADSL G.994 training
ip_nat_rtsp v0.01 loading
==> Bcm963xx Software Version: RU_1.11 <==
device usb0 entered promiscuous mode
br0: port 1(usb0) entering learning state
br0: topology change detected, propagating
br0: port 1(usb0) entering forwarding sta鬳
device eth0 entered promiscuous mode
br0: port 2(eth0) entering learning state
br0: port 2(eth0) entering forwarding state
ADSL G.992 started
Setting SSID "Dlink-2650BU"
SIOCG蒄FLAGS: No such device
Setting country code using abbreviation: "CN"
ADSL G.992 channel analysis
wlctl: Not Found
channel 1 selected
wl0: current channel 1
device wl0 entered promiscuous mode
br0: port 3(wl0) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0) entering forwarding state
ADSL G.992 message exchange
ADSL link up, fast, us}672, ds=4928
BcmRfc2684_init interface is not up nas_0_0_35!
pvc2684ctl -a -v 0.0.35 &
pvc2684d: Interface "nas_0_0_35" created sucessfully
pvc2684d: 胦mmunicating ov錼 ATM 0.0.35, encapsulation: LLC
+++steven: in frontend.c:main:13
argv = dhcpd
argv = (null)
k++steven: in dhcpd.c:udhcpd:188
device usb0 left promiscuous mode
br0: p飏t 1(usb0) entering 鋓sabled state
device eth0 left promiscuous mode
br0: port 2(eth0) entering disabled state
device wl0 left promiscuous mode
br0: port 3(wl0) entering disabled state
device usb0 entered promiscuous mode
br0: port 1(usb0) entering learning state
br0: topology change de鬳ct錮, propagat閚g
鈘0:`port 1(u骲0) entering forwarding state
device eth0 entered promiscuous mode
br0: port 2(eth0) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0) entering forwarding state
device wl0 entered promiscuous mode
br0: port 3(wl0) entering learning state
br0: topology chang?detected, propagating
br0: port 3(wl0) entering forwarding state
ioctl, p_name=diapd
I am open &async_queue = 0xc004a584<3>kill_fasync: bad magic number in fasync_struct!
wlButtonInit open success
gpio_fasync
Pasync_駏eue->magic = 0x4601
*** diapwait system init 1 sec start
##############status LED blink now##################
br0: port 1(usb0) entering disabled state
*** diapwait system init 1 sec end
dft, wanIpAddress = , wanSubnetMask =
vpi = 0, vci = 35, conId = 1, portId = 0
nat = 1, firewall = 1
tr69c: start with default interface nas_0_0_35
Intrusion -> IN=nas_0_0_35 OUT= MAC=00:74:04:e4:15:92:00:18:82:1c:c6:95:08:00 SRC=61.191.56.117 DST=219.159.102.16 LEN=40 TOS=0x00 PREC=0x00 TTL=112 ID=256 P襉TO=TCP SPT=6000 DPT=135 WINDOW=16384 RES=0x00 SYN URGP=0
Intrusion -> IN=nas_0_0_35 OUT= MAC=00:74:04:e4:15:92:00:18:82:1c:c6:95:08:00 SRC=203.171.237.237 DST=219.159.102.16 LEN=40 TOS=0x00 PREC=0x00 TTL=111 ID=256 PROTO=TCP SPT=6000 DPT=1433 WINDOW=16384 RES=0x00 SYN URGP=0
Intrusion -> IN=nas_0_0_35 OUT= MAC=00:74:04:e4:15:92:00:18:82:1c:c6:95:08:00 SRC=121.35.0.83 D覶=219.159.102.16 LEN=48 TOS=0x00 PREC=0x00 TTL=119 ID=22661 DF PROTO=TCP SPT=1105 DPT=4782 WINDOW=65535 RES=0x00 SYN URGP=0
Intrusion -> IN=nas_0_0_35 OUT= MAC=00:74:04:e4:15:92:00:18:82:1c:c6:95:08:00 SRC=121.35.0.83 DS?219.159.102.16 LEN=48 TOS=0x00 PREC=0x00 TTL=119 ID=23448 DF PROTO=TCP SPT=1105 DPT=4782 WINDOW=65535 RES=0x00 SYN URGP=0
Intrusion -> IN=nas_0_0_35 OUT= MAC=00:74:04:e4:15:92:00:18:82:1c:c6:95:08:00 SRC=121.35.0.83 DST=219.159.102.16 LEN=48 TOS=0x00 PREC=0x00 TTL=119 ID=24689 DF PROTO=TCP SPT=1105 DPT=4782 WINDOW=v5535 RES=0xp0 SYN URGP=0
界面如下图