[MINE出品] 中兴ZXDSL W300 V1版启动全过程及TTL接线示意图
Minimal POST completed... Success.Last reset cause: Hardware reset (Power-on reset)
ZXV10 W300 BOOT 1.0 rev: 1.2.5.10
(c) Copyright 2004-2005 ZTE CORPORATION. All Rights Reserved.
Press ESC for monitor... 1
ZXV10 W300>
Booting...
Launching kernel decompressor.
Starting LZMA Uncompression Algorithm.
Copyright (C) 2005 ZTE Corporation.
Compressed file is LZMA format.
Kernel decompressor was successful ... launching kernel.
LINUX started...
Config serial console: ttyS0,9600
CPU revision is: 00018448
Primary instruction cache 16kb, linesize 16 bytes (4 ways)
Primary data cache 16kb, linesize 16 bytes (4 ways)
Number of TLB entries 16.
Linux version 2.4.17_mvl21-malta-mips_fp_le (root@XLVersion) (gcc version 2.96 20000731 (Red Hat Linux 7.3 2.96-113.2) neon) #2 Wed Oct 25 16:48:17 CST 2006
Determined physical RAM map:
memory: 14000000 @ 00000000 (reserved)
memory: 00020000 @ 14000000 (ROM data)
memory: 00fe0000 @ 14020000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line:
calculating r4koff... 000b71b0(750000)
CPU frequency 150.00 MHz
Calibrating delay loop... 149.91 BogoMIPS
Freeing Adam2 reserved memory
Memory: 14380k/16384k available (1487k kernel code, 2004k reserved, 75k data, 60k init)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction...unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
TI Optimizations: Allocating TI-Cached Memory Pool.
Warning: Number of buffers is not configured.Setting default to 512
Using 576 Buffers for TI-Cached Memory Pool.
DEBUG: Using Hybrid Mode.
NSP Optimizations: Succesfully allocated TI-Cached Memory Pool.
Initializing RT netlink socket
Starting kswapd
Disabling the Out Of Memory Killer
devfs: v1.7 (20011216) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
pty: 32 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0xa8610e00 (irq = 15) is a 16550A
ttyS01 at 0xa8610f00 (irq = 16) is a 16550A
oyyz_vlynq init
Vlynq CONFIG_MIPS_AVALANCHE_VLYNQ_PORTS=2
Vlynq Device vlynq0 registered with minor no 63 as misc device. Result=0
Vlynq instance:0 Link UP
Vlynq Device vlynq1 registered with minor no 62 as misc device. Result=0
VLYNQ 1 : init failed
switch_connect ok
switchadd ok
switch start
--oyyz config the watch dog
--oyyz enable the watch dog
oyyz_wlan_005
oyyz_wlan_006
block: 64 slots per queue, batch=16
oyyz_ports=1
Cpmac driver is allocating buffer memory at init time.
Cpmac driver Disable TX complete interrupt setting threshold to 20.
Default Asymmetric MTU for eth0 1500
PPP generic driver version 2.4.1
avalanche flash device: 0x400000 at 0x10000000.
Found: Fujitsu S29GL032R3
Physically mapped flash:0: Found 1 x16 devices at 0x0 in 16-bit mode
number of JEDEC chips: 1
Looking for mtd device :mtd0:
Found a mtd0 image (0xa0000), with size (0x360000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x000a0000-0x00400000 : "mtd0"
Looking for mtd device :mtd1:
Found a mtd1 image (0x20000), with size (0x80000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00020000-0x000a0000 : "mtd1"
Looking for mtd device :mtd2:
Found a mtd2 image (0x0), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00000000-0x00010000 : "mtd2"
Looking for mtd device :mtd3:
Found a mtd3 image (0x10000), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00010000-0x00020000 : "mtd3"
Looking for mtd device :mtd4:
Found a mtd4 image (0x20000), with size (0x3e0000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00020000-0x00400000 : "mtd4"
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 1024)
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.0 (128 buckets, 1024 max) - 364 bytes per conntrack
ip_tables: (c)2000 Netfilter core team
netfilter PSD loaded - (c) astaro AG
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
Initializing the WAN Bridge.
Please set the MAC Address for the WAN Bridge.
Set the Environment variable 'wan_br_mac'.
MAC Address should be in the following format: xx.xx.xx.xx.xx.xx
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k freed
serial console detected.Disabling virtual terminals.
console=/dev/tts/0
init started:BusyBox v0.61.pre (2006.10.25-08:57+0000) multi-call binary
Starting pid 9, console /dev/tts/0: '/etc/init.d/rcS'
Algorithmics/MIPS FPU Emulator v1.5
Reading Standard Configuration File /etc/led.conf
Configured 19 states
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/net/avalanche_usb/avalanche_usb.o
USB: Entering USB_init_module.
USB Driver built for RNDIS-CDC protocols.
Error getting protocol configuration from bootloader environment.
Defaulting to "RNDIS-CDC" mode.
USB: Error getting mac from bootloader enviroment for usb0
USB: Using default mac address: 00.E0.A6.66.41.EB
USB: Error getting mac from bootloader enviroment for usb0
USB: Using default mac address: 00.E0.A6.66.41.E1
VID = 0x451
PID = 0x6060
No Serial Number String present.
Manufacturer = Texas Instruments
Product description = Texas Instruments CDC Ethernet/RNDIS Adapter
USB: Entering USB_Init.
USB: Leaving USB_Init.
Default Asymmetric MTU for usb0 1500
USB: Leaving USB_init_module.
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/atm/tiatm.o
registered device TI Avalanche SAR
Sangam detected
DBG----: autopvc_enable=1(1: autoPVC ok, 2: unK=1 and 54chg, 3: unK=0 Greg's suggestion) chInfo.FwdUnkVc set to 1.
DSP binary filesize = 356930 bytes
tn7dsl_set_modulation : Setting mode to 0x1
Texas Instruments ATM driver: version:
Waiting for enter to start '/bin/sh' (pid 30, terminal /dev/tts/0)
Please press Enter to activate this console. hello_busybox
hello_busybox
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
Doing BRCTL ...
addbr br0
Dtn7dsl_set_modulation : Setting mode to 0x1
oing BRCTL ...
addbr br1
Doing BRCTL ...
addbr br2
$$$$start server flag can not find
$$$$start server flag can not find
$$$$start server flag can not find
Sep8 12:00:18 cfgmgr(snmpcm): snmpd starts (1)
Sep8 12:00:18 cfgmgr(sntp): NTP Polling Timer for DHCP Started succesfully.
Sep8 12:00:18 cfgmgr(sar): DSL Polling Timer Started succesfully.
Sep8 12:00:18 cfgmgr(sar): doing modulation_set.
Sep8 12:00:18 cfgmgr(fdb): Firewall NAT service started
Sep8 12:00:18 : Error getting protocol configuration from bootloader environment.
Sep8 12:00:18 : Defaulting to "RNDIS-CDC" mode.
Sep8 12:00:18 USB: Error getting mac from bootloader enviroment for usb0
Sep8 12:00:18 USB: Using default mac address: 00.E0.A6.66.41.EB
Sep8 12:00:18 USB: Error getting mac from bootloader enviroment for usb0
Sep8 12:00:18 USB: Using default mac address: 00.E0.A6.66.41.E1
Sep8 12:00:18 : VID = 0x451
Sep8 12:00:18 : PID = 0x6060
Sep8 12:00:18 : No Serial Number String present.
Sep8 12:00:18 : Manufacturer = Texas Instruments
Sep8 12:00:18 : Product description = Texas Instruments CDC Ethernet/RNDIS Adapter
Sep8 12:00:18 USB: Entering USB_Init.
Sep8 12:00:18 USB: Leaving USB_Init.
Sep8 12:00:18 : Default Asymmetric MTU for usb0 1500
Sep8 12:00:18 USB: Leaving USB_init_module.
Sep8 12:00:18 : registered device TI Avalanche SAR
Sep8 12:00:18 : Sangam detected
Sep8 12:00:18 DBG----: autopvc_enable=1(1: autoPVC ok, 2: unK=1 and 54chg, 3: unK=0 Greg's suggestion) chInfo.FwdUnkVc set to 1.
Sep8 12:00:18 : DSP binary filesize = 356930 bytes
Sep8 12:00:18 tn7dsl_set_modulation : Setting mode to 0x1
Sep8 12:00:18 Texas Instruments ATM driver: version:
Sep8 12:00:18 tn7dsl_set_modulation : Setting mode to 0x1
Sep8 12:00:18 : Default Asymmetric MTU for br0 1500
Sep8 12:00:18 cfgmgr(lanbridge0): Bridge Created: br0
Sep8 12:00:18 : Default Asymmetric MTU for br1 1500
Doing BRCTL ...
setfilter br0 0
Doing BRCTL ...
addif br0 eth0
Sep8 12:00:19 cfgmgr(lanbridge1): Bridge Created: br1
Doing BRCTL ...
setfilter br1 0
Sep8 12:00:19 cfgmgr(lanbridge2): Bridge Created: br2
Doing BRCTL ...
setfilter br2 0
Doing BRCTL ...
stp br0 off
Doing BRCTL ...
stp br1 off
Sep8 12:00:20 cfgmgr(lanbridge0): Bridge Interface Added: eth0
$$$$start server flag can not find
Doing BRCTL ...
setfilter br0 0
Doing BRCTL ...
stp br2 off
Sep8 12:00:21 : Default Asymmetric MTU for br2 1500
Sep8 12:00:24 : Default Asymmetric MTU for wlan0 1500
Sep8 12:00:24 cfgmgr(ap): AP Driver configuration successful
Sep8 12:00:27 cfgmgr(ap): AP IS UP
Sep8 12:00:27 :
Doing BRCTL ...
addif br0 wlan0
Sep8 12:00:27 : !!!!!!tiap_param_set_max_user_num val=30
Sep8 12:00:27 : dda_ioctl_priv_go call wdrv_init
Sep8 12:00:27 244:
Sep8 12:00:27 802.11d is 244: ** Enabled **
Sep8 12:00:27 244: 802.11h is 244: disabled.
Sep8 12:00:27 244: Country String is: 'CN '
Sep8 12:00:27 244: Configuration succeeded !!!
Sep8 12:00:27 244: WLAN driver database is up
Sep8 12:00:27 : Resetting the remote device.
Sep8 12:00:27 : Un-resetting the remote device.
Sep8 12:00:27 : About to re-init the VLYNQ.
Sep8 12:00:27 : Re-initialized the VLYNQ.
Sep8 12:00:27 245: AcxRegAddr = 0xA4040000, AcxMemAddr = 0xA4000000
Sep8 12:00:27 245: whal_acxProcInitiate: found DEVICE_VENDOR ID = 0x9066104c
Sep8 12:00:27 245: whal_acxProcInitiate: Cpu halt -} download code
Sep8 12:00:27 245: whal_acxProcLoadFwImage: 0xa4000000, 0x0
Sep8 12:00:27 245: whal_acxProcLoadFwImage() -- Loading FW image245: Compiled for RADIA (bg) radio
Sep8 12:00:27 245: whal_acxProcLoadFwImage: 1, pBuf=0xc00af9d0, len=0x15564. Extra pBuf=0x0, len=0x94cfbd09
Sep8 12:00:27 cfgmgr(lanbridge0): Bridge Interface Added: wlan0
Sep8 12:00:27 245: whal_acxProcLoadFwImage: 2, pBuf=0xc00af9d0, len=0x15564. Extra pBuf=0x0, len=0x94cfbd09
$$$$start server flag can not find
Doing BRCTL ...
setfilter br0 0
Sep8 12:00:28 245: whal_acxProcLoadFwImage: 3, pBuf=0xc00af9d0, len=0x15564, DataLen=0x1555c
Sep8 12:00:28 245: whal_acxProcLoadFwImage: 4, pBuf=0xc00af9d0, len=0x15564
Sep8 12:00:28 245: whal_acxProcLoadFwImage: Checksum, calc=0x71e76f, file=0x71e76f
Sep8 12:00:28 255: Tx is up
Sep8 12:00:28 : wdrv_init call wlan_memMngrInit
Sep8 12:00:28 : firstFreeMSDU reset!!!!
Sep8 12:00:28 255: MemMngr is up
Sep8 12:00:28 255: main state machine is up
Sep8 12:00:28 276: WDRV_MAINSM: WLAN Driver initialized successfully
Sep8 12:00:28 :
Sep8 12:00:28 276: WDRV_4X: 4x Disabled
Sep8 12:00:28 276: WDRV_4X: Concatenation Disabled
Sep8 12:00:28 276: WDRV_4X: Ack Emulation Disabled
Sep8 12:00:28 276: whal_apiStartBss: Enable Tx, Rx and Start the Bss
Sep8 12:00:28 276: ----------------------------------------------------------------
Sep8 12:00:28 276: ----------------------------------------------------------------
Sep8 12:00:28 276: START BSS, SSID=BAVO, BSSID=00-D0-D0-B8-56-89
Sep8 12:00:28 276: ----------------------------------------------------------------
Sep8 12:00:28 276: ----------------------------------------------------------------
Sep8 12:00:28 276:AP Power Level = 1
Sep8 12:00:28 276:Regulatory Domain = ETSI
Sep8 12:00:28 276: Net : Channel=11
Sep8 12:00:28 276: ----------------------------------------------------------------
Sep8 12:00:28 276: FW Watchdog is Enabled
Sep8 12:00:28 tiwlan_ddaDoIoctl : Unknown ioctl 35143
Sep8 12:00:28 dda: Both buf and buf_len must be valid.
Sep8 12:00:40 : DSL in Sync
Sep8 12:00:48 cfgmgr(sar): DSL Carrier is up
TTL接线图
printenv
ZXV10 W300> printenvbootloaderVersion 1.2.5.10
ProductID ZXV10 W300
HWRevision 1.0
SerialNumber 001
IPA 192.168.1.1
mtd0 0x900a0000,0x90400000
mtd1 0x90020000,0x900a0000
mtd2 0x90000000,0x90010000
mtd3 0x90010000,0x90020000
mtd4 0x90020000,0x90400000
BOOTCFG m:f:"mtd1"
MAC_PORT 1
MEMSZ 0x01000000
FLASHSZ 0x00400000
MODETTY0 9600,n,8,1,hw
MODETTY1 9600,n,8,1,hw
CPUFREQ 150000000
SYSFREQ 125000000
PROMPT ZXV10 W300>
vcc_encaps0 0.0
vcc_encaps1 0.0
vcc_encaps2 0.0
vcc_encaps3 0.0
vcc_encaps4 0.0
vcc_encaps5 0.0
vcc_encaps6 0.0
vcc_encaps7 0.0
modulation MMODE
SerialNumber1 C500040000000000000000D0D0B85689echo SerialNumber1
HWA_0 00:D0:D0:B8:56:89
HWA_1 00:D0:D0:B8:56:89
HWA_3 00:D0:D0:B8:56:89
mac_ap 00:D0:D0:B8:56:89 哈哈,JTAG也有座,可惜没有支持的JTAG软件. 原帖由 hotqj 于 2008-8-5 23:48 发表 http://www.chinaqos.com/images/common/back.gif
哈哈,JTAG也有座,可惜没有支持的JTAG软件.
我昨天去电脑城买接线端子了，可惜找了一圈都没有找到我想要的。 我来看一下.不过很多不太懂.呵呵 我估计楼主也看不太懂的。 原帖由 MINE 于 2008-8-6 00:01 发表 https://www.chinadsl.net/images/common/back.gif
我昨天去电脑城买接线端子了，可惜找了一圈都没有找到我想要的。
你到修家电的找旧的电视机板子上拆那种接头线，直接插在上面了 原帖由 ygf848 于 2008-8-6 22:04 发表 http://www.chinaqos.com/images/common/back.gif
你到修家电的找旧的电视机板子上拆那种接头线，直接插在上面了
我要各种各样的，电视机板子上没有那么多，那么全。
不过你到提醒了我，过几天去电子商场转转。