xiaoxiong123 发表于 前天 00:30

电信g7615v2光猫编程器救砖无法启动求助大佬们

ttl输出为


SPI NAND
start read bootloader
secure boot
CBC decrypt OK!
CBC decrypt OK!
CBC decrypt OK!
verify OK!
Jump

enter bootloader...
pll init, cpu freq=1000 MHz

crpm init ok
product_vid=77
DDR3 size, 0x20000000=512MiB,HALF_MODE=0
DDR3 1333 Mbps

ddr init ok
SPI NAND
ncfg:1
0,40,b,800
secure uboot
verify OK!
backup header!!
Jump


U-Boot 2021.01 (Mar 03 2024 - 03:42:05 +0800)

CPU: ZX279133@A53x2,1000MHZ
Model: ZTE 133
DRAM:512 MiB
Relocation Offset is: 1d6a8000
clk_register: failed to get sd_wclk_mux device (parent of sd_wclk_div), idx = 0
clk_register: failed to get nand_xclk device (parent of nand_wclk), idx = 1
clk_register: failed to get clk1376m_div device (parent of pon_core_clk_mux), idx = 2
clk_register: failed to get clk40m device (parent of pcie_25m_mux), idx = 3
clk_register: failed to get pon_tm_aclk device (parent of tzc400_pon_aclk), idx = 4
product_vid = 77
vid=77-G7615V2
mtk reset,66
boot_ctrl value=====3
bootsel=3
Disable watchdog.
el=3
NAND:zs->cs_regmap 0000000000000000
zx_sfc_probe: enter
zx_sfc_probe: done
spi_nand spi-flash@0: READ ID data: 01-25-01, skyhigh SPI NAND was found.
spi_nand spi-flash@0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
spinand name:spi-nand0
Creating 14 MTD partitions on "spi-nand0":
0 MiB
Loading Environment from NAND... OK
In:    serial
Out:   serial
Err:   serial
clk_pll env is not setted, core clk won't change
Net:   rx data disable
innerGeLedPolarSet 1
innerGeLedPolarSet 1
innerGeLedPolarSet 1
innerGeLedPolarSet 1
mdio_miiphy_initialize ok
eth0
sec mode!

Hit 1 to upgrade software version
Hit any key to stop autoboot:0
=>


池州老_阮 发表于 前天 02:29

帮楼主顶贴！

Marken888 发表于 前天 17:37

不知道怎么解决，帮楼主顶贴！

xiaoxiong123 发表于 前天 23:12

池州老_阮 发表于 2026-5-30 02:29
帮楼主顶贴！

谢谢老哥

xiaoxiong123 发表于 前天 23:42

Marken888 发表于 2026-5-30 17:37
不知道怎么解决，帮楼主顶贴！

谢谢老哥

yuagonc 发表于 前天 23:50

有备份原机器的编程器固件的话，替换boot应该就行

xiaoxiong123 发表于 昨天 01:33

yuagonc 发表于 2026-5-30 23:50
有备份原机器的编程器固件的话，替换boot应该就行

原机的因为spi坏块所以彻底没了

why002 发表于 昨天 10:37

帮楼主顶贴！帮楼主顶贴！

xiaoxiong123 发表于 昨天 20:00

why002 发表于 2026-5-31 10:37
帮楼主顶贴！帮楼主顶贴！

谢谢老哥
页: [1]
查看完整版本: 电信g7615v2光猫编程器救砖无法启动求助大佬们