创维 D847N-------ttl跑码后这样
输入用户名密码的时候一闪而过，来不及输入，按Ctrl+c或者D都不能中断SPI NAND
start read bootloader
non secure boot
Jump
enter bootloader...
pll init, cpu freq=1000 MHz
crpm init ok
DDR3 16bit 1600 Mbps
DDR3 size 0x20000000=512MiB
ddr init ok
U-Boot 2021.01-svn308776 (Oct 25 2024 - 18:28:46 +0800)
CPU: ZX279133@A53x2,1000MHZ
Model: ZTE 133
DRAM:512 MiB
Relocation Offset is: 17f3c000, fdt_blob: 0x9f6efd40
clk_register: failed to get sd_wclk_mux device (parent of sd_wclk_div), idx = 0
clk_register: failed to get nand_xclk device (parent of nand_wclk), idx = 1
clk_register: failed to get clk1376m_div device (parent of pon_core_clk_mux), id x = 2
clk_register: failed to get clk40m device (parent of pcie_25m_mux), idx = 3
clk_register: failed to get pon_tm_aclk device (parent of tzc400_pon_aclk), idx = 4
vid is
leds DTS probe by vid, successed
Disable watchdog.
el=3
NAND:zs->cs_regmap 0000000000000000
zx_sfc_probe: enter
zx_sfc_probe: done
spi_nand spi-flash@0: READ ID data: ef-aa-22, Winbond SPI NAND was found.
spi_nand spi-flash@0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 1 28
spinand name:spi-nand0
Creating 15 MTD partitions on "spi-nand0":
0 MiB
Loading Environment from NAND... OK
In: serial
Out: serial
Err: serial
clk_pll env is not setted, core clk won't change
read partition others
Size not on a page boundary (0x800), rounding to 0x800
Reading 2048 byte(s) (1 page(s)) at offset 0x00580000
SOFT VID(0x13300002) set failed, please set it again!
vid is
enter outerphy info init!
get board_info_id by fdt,the phy_id is 0x2
Net: rx data disable
The initial value of mdio_8226_id is 1.
innerGeLedPolarSet 1
innerGeLedPolarSet 1
innerGeLedPolarSet 1
innerGeLedPolarSet 1
mdio_miiphy_initialize ok
enter gpon pon pll cfg
mode_xgpon_nsyn_cfg_133
com_pll_lock_ready
rx los =0 rx data in
cdr_lock_ready
pon serdes init succeed
bosa_and_switch_ponmode_info=0x5200040.
switch_ponmode=0x40,multi_bosa_en=0x0,bosa_type=0x2.
read partition others
Reading 4096 byte(s) (2 page(s)) at offset 0x00000000
pKeyName=skyregioncode value=307 tmp=0x00000133
regioncode = 307
read partition others
Reading 4096 byte(s) (2 page(s)) at offset 0x00000000
pKeyName=factoryrestore value=0 tmp=0x00000000
read partition others
Reading 4096 byte(s) (2 page(s)) at offset 0x00000000
pKeyName=UpModeInfo value=64 tmp=0x00000040
UpModeInfo=0x40 ponmode_auto_en=0 upmode=0x40 lan_up_port=0 wlan_u p_port=0
upmode=0x40 ponmode_auto_en=0 lan_up_port=0 wlan_up_port= 0
read partition others
Reading 4096 byte(s) (2 page(s)) at offset 0x00000000
pKeyName=UpModeInfo value=64 tmp=0x00000040
UpModeInfo_str=UpModeInfo=0x00000040
eth0
Hit any key to stop autoboot:0
read partition others
Reading 4096 byte(s) (2 page(s)) at offset 0x00000000
do_mcupg function enter..
val =0xffffffff, reg = 0x192c0004
reset val =0xfffffffe
restore val = 0xffffffff
read SOPC_CLR_OVER_READY_SMAC = 0x1, mac = 0x0
write SOPC_SEND_EN_CFG_SMAC,mac = 0x0
val =0xffffffff, reg = 0x192c0004
reset val =0xfffffffd
restore val = 0xffffffff
read SOPC_CLR_OVER_READY_SMAC = 0x1, mac = 0x1
write SOPC_SEND_EN_CFG_SMAC,mac = 0x1
val =0xffffffff, reg = 0x192c0004
reset val =0xfffffffb
restore val = 0xffffffff
read SOPC_CLR_OVER_READY_SMAC = 0x1, mac = 0x2
write SOPC_SEND_EN_CFG_SMAC,mac = 0x2
val =0xffffffff, reg = 0x192c0004
reset val =0xfffffff7
restore val = 0xffffffff
read SOPC_CLR_OVER_READY_SMAC = 0x1, mac = 0x3
write SOPC_SEND_EN_CFG_SMAC,mac = 0x3
enter outerphy info init!
get board_info_id by fdt,the phy_id is 0x2
Warning: No outerphy on this port<6>
enter outerphy info init!
get board_info_id by fdt,the phy_id is 0x2
--->phy identifier is
5 serdes option is 0
xmac0 is used.
enter outerphy info init!
get board_info_id by fdt,the phy_id is 0x2
can't find this index!
Warning: No outerphy on this port<5>
idm_ddr_base is 0x00000000b0000000
enter gpon pon pll cfg
mode_xgpon_nsyn_cfg_133
com_pll_lock_ready
rx los =0 rx data in
cdr_lock_ready
pon serdes init succeed
np init ok
mac 0 link down
mac 1 link down
mac 2 link down
mac 3 link down
mac 4 link down
multi upgrade check timeout.
Receive multicast packet failed (>.<)
read partition others
Reading 4096 byte(s) (2 page(s)) at offset 0x00000000
BootImageNum=0x00000000,0
name is kernel0,offset is 0x200000
read partition kernel0
Size not on a page boundary (0x800), rounding to 0x14ae000
Reading 21684224 byte(s) (10588 page(s)) at offset 0x00000000
find kernel0 flash entry is 0x200000
read partition boot
Reading 1572864 byte(s) (768 page(s)) at offset 0x00000000
set bootargs,str is console=ttyAMA0,115200n8 rdinit=/sbin/init U-Boot 2.0.0 2024 1025183308 0x200000 0x0 0x83 0x83UpModeInfo=0x00000040
set bootargs,str is console=ttyAMA0,115200n8 rdinit=/sbin/init U-Boot 2.0.0 2024 1025183308 0x200000 0x0 0x83 0x83UpModeInfo=0x00000040regioncode=0x133
Saving Environment to NAND... Erasing NAND...
Erasing at 0x1c0000 -- 100% complete.
Writing to NAND... OK
OK
config string: #conf@133
## Loading kernel from FIT Image at 88000000 ...
Using 'conf@133' configuration
Trying 'kernel@133' kernel subimage
Description:Linux kernel for 133
Type: Kernel Image
Compression:gzip compressed
Data Start: 0x880000f4
Data Size: 4815863 Bytes = 4.6 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x80080000
Entry Point:0x80080000
Verifying Hash Integrity ... OK
## Loading ramdisk from FIT Image at 88000000 ...
Using 'conf@133' configuration
Trying 'initramfs@133' ramdisk subimage
Description:initramfs for 133
Type: RAMDisk Image
Compression:lzma compressed
Data Start: 0x884a3f24
Data Size: 16815245 Bytes = 16 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x00000000
Entry Point:0x00000000
Verifying Hash Integrity ... OK
WARNING: 'compression' nodes for ramdisks are deprecated, please fix your .its f ile!
## Loading fdt from FIT Image at 88000000 ...
Using 'conf@133' configuration
Trying 'fdt@133' fdt subimage
Description:Flattened Device Tree blob for 133
Type: Flat Device Tree
Compression:uncompressed
Data Start: 0x88497dc8
Data Size: 49307 Bytes = 48.2 KiB
Architecture: AArch64
Load Address: 0x82000000
Verifying Hash Integrity ... OK
Loading fdt from 0x88497dc8 to 0x82000000
Booting using the fdt blob at 0x82000000
Uncompressing Kernel Image
Loading Ramdisk to 9dff2000, end 9effb48d ... OK
Loading Device Tree to 000000009f6de000, end 000000009f6ed09a ... OK
ft_board_setup
ft_fixup_flash spi-nand0
ft_fixup_flash-spinand
Starting kernel ...
CPU0: Set slave cpu addr = 0x00211A8C
SLAVECPU: Cpu = 00000001 online successfully in psci!
init psci ok!!
CPU ON: Target cpu = 00000001 entry = 0x8072B1E0
CPU1: Jump to linux kernel entry = 0x8072B1E0
Booting Linux on physical CPU 0x0000000000
Linux version 4.19.136+ (chenmengxue@skyworth) (gcc version 5.3.1 20160412 (Buil droot 2017.05)) #4 SMP Fri Oct 25 18:33:08 CST 2024
Machine model: ZTE 133
zx_resv_mem: base 0x0000000080b23000 vbase 0xffffffc000b23000 size 0x3245000
OF: reserved mem: initialized node pon_rsvmem, compatible id zxic,resv-memory
psci: probing for conduit method from DT.
psci: PSCIv1.0 detected in firmware.
psci: Using standard PSCI v0.2 function IDs
psci: Trusted OS migration not required
psci: SMC Calling Convention v1.0
random: get_random_bytes called from start_kernel+0xb0/0x414 with crng_init=0
percpu: Embedded 48 pages/cpu s157016 r8192 d31400 u196608
Detected VIPT I-cache on CPU0
CPU features: enabling workaround for ARM erratum 845719
Built 1 zonelists, mobility grouping on.Total pages: 129024
Kernel command line: console=ttyAMA0,115200n8 rdinit=/sbin/init U-Boot 2.0.0 202 41025183308 0x200000 0x0 0x83 0x83UpModeInfo=0x00000040regioncode=0x133
zxic : zxic_cmdline_console : ttyAMA0
g_UpModeInfo=0x40
g_regioncode=307
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Memory: 403064K/524288K available (6846K kernel code, 506K rwdata, 2380K rodata, 640K init, 441K bss, 121224K reserved, 0K cma-reserved)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
rcu: Hierarchical RCU implementation.
rcu: RCU event tracing is enabled.
rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
GICv3: Distributor has no Range Selector support
GICv3: no VLPI support, no direct LPI support
GICv3: CPU0: found redistributor 0 region 0:0x0000000000540000
clk_common: pll_2000m_clk:register pll
clk_common: func of_zx_clk_parse_pll nr rate is 11
clk_common: pll_2000m_clk:no paticular pll-enable-register, use default cfg reg
clk_common: pll_lsp_2000m_clk:register pll
clk_common: pll_lsp_2000m_clk:failed to find property zx-clock,pll-en-bit
clk_common: pll_1376m_clk:register pll
clk_common: pll_1376m_clk:failed to find property zx-clock,pll-en-bit
clk_common: pll_fpp_2500m_clk:register pll
clk_common: pll_fpp_2500m_clk:failed to find property zx-clock,pll-en-bit
arch_timer: cp15 timer(s) running at 25.00MHz (virt).
clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, m ax_idle_ns: 440795202646 ns
sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
Console: colour dummy device 80x25
Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes)
ASID allocator initialised with 32768 entries
rcu: Hierarchical SRCU implementation.
common ,zxic_early_init
smp: Bringing up secondary CPUs ...
Detected VIPT I-cache on CPU1
GICv3: CPU1: found redistributor 1 region 0:0x0000000000560000
CPU1: Booted secondary processor 0x0000000001
smp: Brought up 1 node, 2 CPUs
SMP: Total of 2 processors activated.
CPU features: detected: GIC system register CPU interface
CPU features: detected: 32-bit EL0 Support
CPU: All CPU(s) started at EL1
alternatives: patching kernel code
devtmpfs: initialized
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911 2604462750000 ns
futex hash table entries: 512 (order: 3, 32768 bytes)
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
cpuidle: using governor ladder
hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
DMA: preallocated 256 KiB pool for atomic allocations
Serial: AMBA PL011 UART driver
zx reset init
zx2967-reset 10e10060.toprst: reset controller cnt:32
zx2967-reset 10e10070.localrst: reset controller cnt:64
zxic-pinctrl 10e20000.pinctrl: invalid pin list in gpio-range node
zxic-pinctrl 10e20000.pinctrl: invalid pin list in bank-range node
10d0d000.serial: ttyAMA0 at MMIO 0x10d0d000 (irq = 16, base_baud = 0) is a PL011 rev1
console enabled
zte-msi 1f400000.msi: zx pcie msi probe enter!!!!!!
zte-msi 1f400000.msi: parent_node->name : interrupt-controller
zte-msi 1f400000.msi: parent->name : :interrupt-controller@00500000-1
zte-msi 1f400000.msi: zx pcie msi 1 initail!!
zte-msi 1f400000.msi: dbi_base : 0xffffff8009400000
zte-msi 1f400000.msi: vector_phy : 0x10e00004
zte-msi 1f400000.msi: num-vectors : 0x20
zte-msi 1f400000.msi: status-of-woe : 0x0
zx-efuse 14f11000.efuse: efuse init ok, clock rate = 25000000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
clocksource: Switched to clocksource arch_sys_counter
VFS: Disk quotas dquot_6.6.0
VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
zx_gpio 10d10000.gpio: ZX GPIO chip registered
vid is
zx_gpio 10d10040.gpio: ZX GPIO chip registered
vid is
zx_gpio 10d10080.gpio: ZX GPIO chip registered
vid is
zx_gpio 10d100c0.gpio: ZX GPIO chip registered
vid is
zx_gpio 10d10100.gpio: ZX GPIO chip registered
vid is
NET: Registered protocol family 2
tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 16420K
Initialise system trusted keyrings
workingset: timestamp_bits=46 max_order=17 bucket_order=0
exFAT: Version 1.2.9
Key type asymmetric registered
Asymmetric key parser 'x509' registered
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
io scheduler mq-deadline registered
io scheduler kyber registered
interval tree insert/remove
-> 884 cycles
interval tree search
-> 5278 cycles (2692 results)
zx_spi_probe: enter
zx_spi 14f06000.ssp: Failed to request TX DMA channel
zx_spi 14f06000.ssp: Failed to request RX DMA channel
spi spi0.0: zx_spi_setup: mode 0, 8 bpw, 500000 hz
zx_spi 14f06000.ssp: set rate to 961539
zx_sfc_probe: enter
zx-spifc 10d0f000.spifc: spifc rate is set to 125000000
zx_mdio 14f01000.mdio: mdio not set pins
zx_mdio 14f01000.mdio: Cannot found phy-power property in mdio
zx_mdio 14f01000.mdio: MDIO id = 0, clock = 2500000
zx_mdio 14f01000.mdio: MDIO probe success!
zx_mdio 14f02000.mdio: MDIO id = 1, clock = 2500000
zx_mdio 14f02000.mdio: MDIO probe success!
zx_i2c 14f03000.i2c: zx_i2c_probe
<drivers/soc/../../../../../component/linux/common/i2c/i2c_zx.c> before i2c_add_ numbered_adapter i2c->adap.nr is -1
<drivers/soc/../../../../../component/linux/common/i2c/i2c_zx.c> adapter_id is 0
<drivers/soc/../../../../../component/linux/common/i2c/i2c_zx.c> after i2c_add_n umbered_adapter i2c->adap.nr is 0
zx_i2c 14f03000.i2c: clock rate is 25000000
zx_i2c 14f03000.i2c: zx i2c0 probe succeed.
tdm registered!
zx_tdm2.0_probe!
g_tdm_buf =(____ptrval____),9f138000
tdm irq=28
tdm binding cpu1....
tdm softirq
zx_axi_tdm_setup
zx-pwm 14f10000.pwm: zx_pwm_probe done.
zte,zx27913x-pcie 15200000.pcie: zx pcie probe enter!!!!!!
zte,zx27913x-pcie 15200000.pcie: Link down work initialization completed
pcie@15200000:Initialize pcie's phy!!!
pcie@15202000:Initialize pcie's phy!!!
random: fast init done
zte,zx27913x-pcie 15200000.pcie: host bridge /soc/pcie@15200000 ranges:
zte,zx27913x-pcie 15200000.pcie: IO 0x2f000000..0x2f0fffff -> 0x2f000000
zte,zx27913x-pcie 15200000.pcie: MEM 0x20000000..0x2effffff -> 0x20000000
zte,zx27913x-pcie 15200000.pcie:dbi_base = 0xffffff8008e25108 link up val = 0x 51
zte,zx27913x-pcie 15200000.pcie: Link up, speed reg = 0xb0120000
zte,zx27913x-pcie 15200000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource
pci_bus 0000:00: root bus resource (bus address )
pci_bus 0000:00: root bus resource
zte,zx27913x-pcie 15200000.pcie: enable MSI ok
pci 0000:00:00.0: BAR 0: assigned
pci 0000:00:00.0: BAR 8: assigned
pci 0000:00:00.0: BAR 9: assigned
pci 0000:01:00.0: BAR 0: assigned
pci 0000:01:00.0: BAR 2: assigned
pci 0000:01:00.0: BAR 4: assigned
pci 0000:00:00.0: PCI bridge to
pci 0000:00:00.0: bridge window
pci 0000:00:00.0: bridge window
pcieport 0000:00:00.0: Signaling PME with IRQ 32
pcieport 0000:00:00.0: AER enabled with IRQ 32
zte,zx27913x-pcie 15200000.pcie: Request pcie link down irq ok
zte,zx27913x-pcie 15202000.pcie: zx pcie probe enter!!!!!!
zte,zx27913x-pcie 15202000.pcie: Link down work initialization completed
pcie phy has been initialized !!!!!!
zte,zx27913x-pcie 15202000.pcie: host bridge /soc/pcie@15202000 ranges:
zte,zx27913x-pcie 15202000.pcie: IO 0x3f000000..0x3f0fffff -> 0x3f000000
zte,zx27913x-pcie 15202000.pcie: MEM 0x30000000..0x3effffff -> 0x30000000
zte,zx27913x-pcie 15202000.pcie:dbi_base = 0xffffff8008f33108 link up val = 0x 51
zte,zx27913x-pcie 15202000.pcie: Link up, speed reg = 0xb0120000
zte,zx27913x-pcie 15202000.pcie: PCI host bridge to bus 0001:00
pci_bus 0001:00: root bus resource
pci_bus 0001:00: root bus resource (bus address )
pci_bus 0001:00: root bus resource
pci 0001:01:00.0: 4.000 Gb/s available PCIe bandwidth, limited by 5 GT/s x1 link at 0001:00:00.0 (capable of 8.000 Gb/s with 5 GT/s x2 link)
zte,zx27913x-pcie 15202000.pcie: enable MSI ok
pci 0001:00:00.0: BAR 0: assigned
pci 0001:00:00.0: BAR 8: assigned
pci 0001:00:00.0: BAR 9: assigned
pci 0001:01:00.0: BAR 0: assigned
pci 0001:01:00.0: BAR 2: assigned
pci 0001:01:00.0: BAR 4: assigned
pci 0001:00:00.0: PCI bridge to
pci 0001:00:00.0: bridge window
pci 0001:00:00.0: bridge window
pcieport 0001:00:00.0: Signaling PME with IRQ 34
pcieport 0001:00:00.0: AER enabled with IRQ 34
zte,zx27913x-pcie 15202000.pcie: Request pcie link down irq ok
zx_pvt_sensor_cln22ulp 10e70000.pvt: Enabled with temp 0x11e
zx_thermal_init end
zx_pvt_sensor_cln22ulp 10e70000.pvt: probe ok, clock rate: 1190477
<pdt_wdt_init>(485):create proc files for watchdog!!!
<pdt_wdt_init>(490):Starting Watchdog Timer...
wdt debug: nr_cpu_ids= 2
zx_wdt 14f09000.wdt: zxwdt: heartbeat 8 sec, clock 2048
<pdt_wdt_init>(490):Starting Watchdog Timer...
wdt debug: nr_cpu_ids= 2
zx_wdt 14f0a000.wdt: zxwdt: heartbeat 8 sec, clock 2048
<pdt_wdt_init>(490):Starting Watchdog Timer...
wdt debug: nr_cpu_ids= 2
zx_wdt 14f0b000.wdt: zxwdt: heartbeat 8 sec, clock 2048
<pdt_wdt_init>(490):Starting Watchdog Timer...
wdt debug: nr_cpu_ids= 2
zx_wdt 14f0c000.wdt: zxwdt: heartbeat 8 sec, clock 2048
success to get board info
success to get cpu info
success to get port info
success to get enet info
success to get optical info
zx_board soc:bdinfo@0: Property 'pots_info' cannot be read, ret: -22.
success to get pots info
success to get ge info
the count of outerphy_desc is 3!
the outerphy_mode of outerphy_desc: 0!
phy_name:[]_
the outerphy_mode of outerphy_desc: 0!
phy_name:_
the outerphy_mode of outerphy_desc: 0!
phy_name:[]_
success to get outerphy desc info
zx_board soc:bdinfo@0: vid: 2, name: TDY09, zx board probe ok.
success to get board info
success to get cpu info
success to get port info
zx_board soc:tdy0a_4@0: Property 'vid_list' cannot be read, ret: -22.
success to get enet info
success to get optical info
zx_board soc:tdy0a_4@0: Property 'pots_info' cannot be read, ret: -22.
success to get pots info
success to get ge info
the count of outerphy_desc is 3!
the outerphy_mode of outerphy_desc: 0!
phy_name:[]_
the outerphy_mode of outerphy_desc: 0!
phy_name:[]_
the outerphy_mode of outerphy_desc: 0!
phy_name:[]_
success to get outerphy desc info
vid unmatch! try next DTS
success to get board info
success to get cpu info
success to get port info
zx_board soc:tdy0a_5@0: Property 'vid_list' cannot be read, ret: -22.
success to get enet info
success to get optical info
zx_board soc:tdy0a_5@0: Property 'pots_info' cannot be read, ret: -22.
success to get pots info
success to get ge info
the count of outerphy_desc is 3!
the outerphy_mode of outerphy_desc: 0!
phy_name:[]_
the outerphy_mode of outerphy_desc: 0!
phy_name:_
the outerphy_mode of outerphy_desc: 0!
phy_name:[]_
success to get outerphy desc info
vid unmatch! try next DTS
success to get board info
success to get cpu info
success to get port info
zx_board soc:tdy09_0@0: Property 'vid_list' cannot be read, ret: -22.
success to get enet info
success to get optical info
zx_board soc:tdy09_0@0: Property 'pots_info' cannot be read, ret: -22.
success to get pots info
success to get ge info
the count of outerphy_desc is 3!
the outerphy_mode of outerphy_desc: 0!
phy_name:[]_
the outerphy_mode of outerphy_desc: 0!
phy_name:[]_
the outerphy_mode of outerphy_desc: 0!
phy_name:[]_
success to get outerphy desc info
vid unmatch! try next DTS
success to get board info
success to get cpu info
success to get port info
zx_board soc:tdy09_1@0: Property 'vid_list' cannot be read, ret: -22.
success to get enet info
success to get optical info
zx_board soc:tdy09_1@0: Property 'pots_info' cannot be read, ret: -22.
success to get pots info
success to get ge info
the count of outerphy_desc is 3!
the outerphy_mode of outerphy_desc: 0!
phy_name:[]_
the outerphy_mode of outerphy_desc: 0!
phy_name:[]_
the outerphy_mode of outerphy_desc: 0!
phy_name:[]_
success to get outerphy desc info
vid unmatch! try next DTS
zx_board soc:tfy01_7@0: Property 'board_info' cannot be read, ret: -22.
zx_board soc:tfy01_7@0: failed to get board info
cpufreq_zx: zx_cpufreq_driver_init
leds DTS probe by vid, successed
zx-leds-gpio soc:leds_2: 4 led has mux ctrl
zx-leds-gpio soc:leds_2: alloc devid 101711872
pon_plat_probe begin...
temp_pon_plat_need_rsv_mem= 0x3245000
get g_red_cw_in_share_max error! default val is - 1
total_pon_plat_need_rsv_mem=0x3245000
Failed to get optical rxsd signal
Failed to get rtl8367s reset gpio signal
g_tm_max_fast_num=0, g_tm_max_fast_num_v6=0, g_tm_max_fas t_num_l3=0
g_tm_max_opc_flow_num=0
g_zxic_e8_en is set to 0
g_zxic_e8_en is 0
g_epon_open_high=1 use default!
g_epon_open_high=1
bosa_and_switch_ponmode_info=0x5200040,g_switch_ponmode=0x 40,g_kernel_switch_en=0x0,g_multi_bosa_en=0x0,g_bosa_type=0x2,g_switch_time=60
g_UpModeInfo=0x40 g_up_mode=0x40 g_is_auto_ponmode=0 g_lanu p_port=0 g_wlanup_port=0 g_wan_port=0
switch_chip_type is set to 0
mdio_8226_id is set to 1
mdio_8367s_id is set to 0
current_wlan_map is TYPE_133_8SSID.
pon_plat_probe end...
cacheinfo: Unable to detect cache hierarchy for CPU 0
brd: module loaded
loop: module loaded
SCSI Media Changer driver v0.25
spi-nand spi1.0: ID efaa2200, Winbond SPI NAND was found.
spi-nand spi1.0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
dynamic partitions parse
Found 256MiB: 256MiB
15 dynamic-partitions partitions found on MTD device spi1.0
Creating 15 MTD partitions on "spi1.0":
0x000000000000-0x000010000000 : "whole"
random: crng init done
0x000000000000-0x000000200000 : "boot"
0x000004800000-0x000004c00000 : "parameter tags"
0x000000200000-0x000002200000 : "kernel0"
0x000005400000-0x000005800000 : "middleware"
0x000004c00000-0x000005400000 : "usercfg"
0x000002200000-0x000004200000 : "kernel1"
0x000004200000-0x000004800000 : "others"
0x000005800000-0x000005c00000 : "wlan"
0x000005c00000-0x000005e00000 : "phoneapp0"
0x000006000000-0x000007e00000 : "osgi0"
0x000009c00000-0x00000fc00000 : "plugin_data"
0x000007e00000-0x000009c00000 : "osgi1"
0x000005e00000-0x000006000000 : "phoneapp1"
0x00000fc00000-0x000010000000 : "awifi"
libphy: Fixed MDIO Bus: probed
tun: Universal TUN/TAP device driver, 1.6
thunder_xcv, ver 1.0
thunder_bgx, ver 1.0
nicpf, ver 1.0
PPP MPPE Compression module registered
NET: Registered protocol family 24
xhci-hcd 15008000.usb3: xHCI Host Controller
xhci-hcd 15008000.usb3: new USB bus registered, assigned bus number 1
xhci-hcd 15008000.usb3: irq 22, io mem 0x15008000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: xHCI Host Controller
usb usb1: Manufacturer: Linux 4.19.136+ xhci-hcd
usb usb1: SerialNumber: 15008000.usb3
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
xhci-hcd 15008000.usb3: xHCI Host Controller
xhci-hcd 15008000.usb3: new USB bus registered, assigned bus number 2
xhci-hcd 15008000.usb3: Host supports USB 3.1 Enhanced SuperSpeed
usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.19
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: xHCI Host Controller
usb usb2: Manufacturer: Linux 4.19.136+ xhci-hcd
usb usb2: SerialNumber: 15008000.usb3
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
xhci-hcd 15010000.usb3: xHCI Host Controller
xhci-hcd 15010000.usb3: new USB bus registered, assigned bus number 3
xhci-hcd 15010000.usb3: irq 23, io mem 0x15010000
usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: xHCI Host Controller
usb usb3: Manufacturer: Linux 4.19.136+ xhci-hcd
usb usb3: SerialNumber: 15010000.usb3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
xhci-hcd 15010000.usb3: xHCI Host Controller
xhci-hcd 15010000.usb3: new USB bus registered, assigned bus number 4
xhci-hcd 15010000.usb3: Host supports USB 3.1 Enhanced SuperSpeed
usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.19
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: xHCI Host Controller
usb usb4: Manufacturer: Linux 4.19.136+ xhci-hcd
usb usb4: SerialNumber: 15010000.usb3
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
usbcore: registered new interface driver usb-storage
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial support registered for generic
usbcore: registered new interface driver cp210x
usbserial: USB Serial support registered for cp210x
usbcore: registered new interface driver pl2303
usbserial: USB Serial support registered for pl2303
i2c /dev entries driver
u32 classifier
xt_time: kernel timezone is -0000
zte--oss cpu usage module init
:comdev init enter
:comdev init sucess
11930:23:06 [(886)LogStdioProcInit] LogStdioProcInit
LogUdpWatchProcInit
detail_process_init start
Initializing XFRM netlink socket
NET: Registered protocol family 10
Segment Routing with IPv6
sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
Bridge firewalling registered
l2tp_core: L2TP core driver, V2.0
l2tp_ppp: PPPoL2TP kernel driver, V2.0
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
Loading compiled-in X.509 certificates
Loaded X.509 cert 'Build time autogenerated kernel key: bd6a5cb9563a2184cd950e56 662eabd273edf53e'
Key type encrypted registered
zx_gpio_keys: zx gpio keys probe
keys DTS probe by vid, successed
input: soc:keys as /devices/platform/soc/soc:keys/input/input0
br_uc_ffe_init registered melon @
QOSBw module init
==========zxic_notifier_init success=================
multivlan cache ini
br_multivlan_init registered melon @
br_vlantci_init registered melon @
Freeing unused kernel memory: 640K
Run /sbin/init as init process
dmounting /dev/mtdblock2 to /tagparam, wait ...
jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x003437c8: Read 0xfffffff f, calculated 0xf3a43fef
jffs2: Empty flash at 0x0034383c ends at 0x00344000
jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x003447c8: Read 0xfffffff f, calculated 0x58b84118
jffs2: Empty flash at 0x0034483c ends at 0x00345000
jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x003487c8: Read 0xfffffff f, calculated 0xbec1c4c6
jffs2: Empty flash at 0x0034883c ends at 0x00349000
jffs2: Empty flash at 0x00349928 ends at 0x0034a000
djffs2: Empty flash at 0x003c0830 ends at 0x003c1000
jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x003c17c8: Read 0xfffffff f, calculated 0x84bace03
Mounting ramdisk at /var and /usr/cpkTmp
mounting /dev/mtdblock4 middleware to /important_bak, wait ...
jffs2: Empty flash at 0x00008948 ends at 0x00009000
jffs2: Empty flash at 0x0000a344 ends at 0x0000a800
dMounting /dev/mtdblock5 to /userconfig
jffs2: Empty flash at 0x0011b360 ends at 0x0011b800
jffs2: Empty flash at 0x0011d240 ends at 0x0011d800
jffs2: Empty flash at 0x007795f4 ends at 0x00779800
Mount ok!
d--------------- otarget is 0 ---------------
************************** mout mtdblock10 *********************
ddddjffs2: notice: (924) check_node_data: wrong data CRC in data node at 0x0011e fac: read 0x43c5ce84, calculated 0xbbb11b8d.
d
jffs2: notice: (924) check_node_data: wrong data CRC in data node at 0x0011cd98: read 0xeb8464b5, calculated 0x4221e37b.
ddd
d
11930:23:10 start pKeyName= factoryrestore, value=ffffff01!
11930:23:10 end value=0!
djffs2: Empty flash at 0x02b4ff34 ends at 0x02b50000
jffs2: Empty flash at 0x02b52f18 ends at 0x02b53000
dddjffs2: Empty flash at 0x04b28960 ends at 0x04b29000
ddMount ok!
--------------- ptarget is 0 ---------------
************************** mout mtdblock9 *********************
sismac region_code 307
sismac region code euqal 307
11930:23:11 start pKeyName= skyregioncode, value=ffffff01!
11930:23:11 end value=133!
region code euqal 307
11930:23:11 start pKeyName= factoryrestore, value=ffffff01!
11930:23:11 end value=0!
Mounting /dev/mtdblock14 at /usr/local/awifi
mount: mounting /dev/mtdblock14 on /usr/local/awifi failed: No such file or dire ctory
idx_bak is not empty
USR_CFG_TYPE_FILE_BAK flag is ok
mounting /dev/mtdblock8 to /wlan, wait ...
djffs2: Empty flash at 0x00143014 ends at 0x00143800
Configuring MAC interfaces
ls: /etc/sysconfig/network-scripts/ifcfg-mii*: No such file or directory
Bringing up interface lo
*****************set bindv6only********************
init_module: umod=0000000048a13e52, len=262712, uargs=000000007b29053c
bspdriver: loading out-of-tree module taints kernel.
bspdriver: module verification failed: signature and/or required key missing - t ainting kernel
qupengchao : symname is init_module
zx_sec_init
storage_wakeup_proc_create success!
uboot cmd_line: U-Boot 2.0.0 20241025183308 0x200000 0x0 0x83 0x83 UpModeInfo=0x00000040regioncode=0x133
bootversion: 2.0.0, bootbuildtime: 2024-10-25 18:33:08
kernel offset: 0x200000, active partion: 0
no sec mode, read mtd.
s8HardVersion is V2.0
s32Description is ZXIC 133 UNI V2.0.0 286632 CM O
s8VendorInfo is ZXIC
ds8InnerVersion is CMDV1.0.011
phoneapp is 2.0.0
zx_vsinfo_init done
zx_vsinfo_probe ret is 0
zxic_vid_init
start i2c_1 setup.
can't get i2c adapter 1
start i2c_0 setup.
init chip, g_up_mode=0x40
GN28L95 read table 0xFF chipname-register success,chipname=0xFF.
UX3360 read table 0x86 register(0x80~0x85) success,chipname=.
UX3361 read table 0x87 register(0x80~0x85) success,chipname=UX33631.
dbsp_mcu_eeprom_mode_select read table register success.
judge chip select mcu(0x*0) or eeprom(0x*1) mode ! count=0, judge_reg=0xFF.
bsp_chip_probe count=0, r_data=0x00.
UX3361 found.
bspdriver select mode is MCU.
zxic_slic_adapter_init init success.
sky: slic_spi_bus_id is , fpga_spi_bus_id is
bsp_spi_init can not :spi0.1
bsp_spi_init can not :spi0.2
bsp_spi_init can not :spi0.3
bsp_spi_init can not :spi1.1
bsp_spi_init can not :spi1.2
bsp_spi_init can not :spi1.3
=== verify slic info ===
try mode: 1
slic mode pcm
0x00000008,0x00000008
zx_axi_tdm_setup
zx_axi_tdm_reset,TDM reset ok
found a port:0 cs:0 ch:0
Lantiq chip dxs found!
slic_rst_gpio 6 pull down
dslic_rst_gpio 6 pull down
kylin630 chip id error! 0x0
slic_rst_gpio 6 pull down
Siliconlab chip id error! 0x0
slic_rst_gpio 6 pull down
rcn:0x0 pcn:0x0
can't found id.
try mode: 2
slic mode isi
0x00000009,0x00000009
zx_axi_tdm_setup
zx_axi_tdm_reset,TDM reset ok
dfound a port:0 cs:0 ch:0
Lantiq chip dxs found!
slic_rst_gpio 6 pull down
slic_rst_gpio 6 pull down
kylin630 chip id error! 0x0
slic_rst_gpio 6 pull down
Siliconlab chip id error! 0x0
dslic_rst_gpio 6 pull down
rcn:0x0 pcn:0x0
can't found id.
try mode: 3
slic mode zsi
0x00000009,0x00000009
zx_axi_tdm_setup
zx_axi_tdm_reset,TDM reset ok
found a port:0 cs:0 ch:0
Lantiq chip dxs found!
slic_rst_gpio 6 pull down
slic_rst_gpio 6 pull down
dkylin630 chip id error! 0xff
slic_rst_gpio 6 pull down
Siliconlab chip id error! 0xff
<3000000008>11930:23:12 [(1102)CheckLogConfFile] CheckLogConfF ile%CheckRestartCntConfFile
slic_rst_gpio 6 pull down
rcn:0xff pcn:0xff
can't found id.
verify_slicinfo ERROR
siliconlab_line_num: 0, zarlink_line_num: 0, kylin_line_num: 0, total_line_num: 0
kernel_frw
read: kernel_frw
read: kernel_frw
xmac0 phy is phy_RTL8226
init_module: umod=000000006c23bced, len=67864, uargs=000000007b29053c
dqupengchao : symname is init_module
Start insmod R8226b_init!
r8226b_phy_probe: 576: rtl8226b Phy Driver Probe Done
result = 1
R8226b init success!
xmac1 phy is
xmac1 no use
init_module: umod=000000007b00a603, len=5208864, uargs=000000007b29053c
np_133: magic '4.19.136 SMP mod_unload aarch64' should be '4.19.136+ SMP mod_unl oad aarch64'
dddqupengchao : symname is init_module
init plat module
zx_timer0_probe: ==========zx_timer0_probe>g_timer0_irq=0
zx_timer0_irq_base_of_init: ==========1>g_timer0_irq=0
get timer0 irq succeed,g_timer0_irq:14
zx_timer0_irq_base_of_init: ==========>g_timer0_irq=14,timer0_base=0xffffff8008c 8d000
get timer2 irq succeed,g_timer2_irq:15
pon init
sys_ctrl_base is 0xffffff8008c9d000
top_crm_base is 0xffffff80093d0000
pin_mux_base is 0xffffff8008ca5000
efuse_base is 0xffffff8008cad000
pon_base is 0xffffff800d000000
g_pon_irq:29
pps_base is 0xffffff800f000000
nppt_base is 0xffffff8011000000
rgmii_base is 0xffffff8009900000
pon_serdes_base is 0xffffff8009810000
pon_serdes_pll_base is 0xffffff8009830000
uni_serdes_base is 0xffffff800a100000
pcu_base is 0xffffff8009850000
gephy_apb_base is 0xffffff800e800000
idm-intr0 is 40
idm-intr1 is 41
idm-intr2 is 42
idm-intr3 is 43
zx_pon_irq_base_of_init: idm_ddr_phy_start 0x80b23000, idm_ddr_size 0xee5000
xmac0_pcs_base is 0xffffff8014000000
hol not enable
enter gpon pon pll cfg
mode_xgpon_nsyn_cfg
com_pll_lock_ready
rx los =0 rx data in
cdr_lock_ready
pon serdes init succeed
pon mode is xg
idm cci enable
CLK_MUX_3 is 0x06713277,CLK_EN_6 is 0x00001fd7.
val =0xffffffff, reg = 0x000000002c1966ab
reset val =0xffffffef
val =0xffffffef, reg = 0x000000002c1966ab
reset val =0x7fffffef
restore val = 0xffffffef
nppt init done ok. cnt = 0
val =0xffffffef, reg = 0x000000002c1966ab
restore val = 0xffffffff
pon int
nppt int
pon probe init ok
nppt init start
init gephy apb base
val =0xffffffff, reg = 0x000000002c1966ab
reset val =0xfffffffe
restore val = 0xffffffff
enter smac_init
smac_init: smac_pkt_filter = 0x80000001, mac = 0x0
write smac an ctrl ,mac = 0x0
read SOPC_CLR_OVER_READY_SMAC = 0x1, mac = 0x0
write SOPC_SEND_EN_CFG_SMAC,mac = 0x0
sopc send enable ,mac = 0x0
exit smac_init:mac=0x0
val =0xffffffff, reg = 0x000000002c1966ab
reset val =0xfffffffd
restore val = 0xffffffff
enter smac_init
smac_init: smac_pkt_filter = 0x80000001, mac = 0x1
write smac an ctrl ,mac = 0x1
read SOPC_CLR_OVER_READY_SMAC = 0x1, mac = 0x1
write SOPC_SEND_EN_CFG_SMAC,mac = 0x1
sopc send enable ,mac = 0x1
exit smac_init:mac=0x1
val =0xffffffff, reg = 0x000000002c1966ab
reset val =0xfffffffb
restore val = 0xffffffff
enter smac_init
smac_init: smac_pkt_filter = 0x80000001, mac = 0x2
write smac an ctrl ,mac = 0x2
read SOPC_CLR_OVER_READY_SMAC = 0x1, mac = 0x2
write SOPC_SEND_EN_CFG_SMAC,mac = 0x2
sopc send enable ,mac = 0x2
exit smac_init:mac=0x2
val =0xffffffff, reg = 0x000000002c1966ab
reset val =0xfffffff7
restore val = 0xffffffff
enter smac_init
smac_init: smac_pkt_filter = 0x80000001, mac = 0x3
write smac an ctrl ,mac = 0x3
read SOPC_CLR_OVER_READY_SMAC = 0x1, mac = 0x3
write SOPC_SEND_EN_CFG_SMAC,mac = 0x3
sopc send enable ,mac = 0x3
exit smac_init:mac=0x3
ERROR:param-><index:1><outerphy->outerphy_name:0x8af56d9>
<outerphy_attr_array.outerphy_name:realtek fephy>
ERROR:param-><index:2><outerphy->outerphy_name:0x8af56d9>
<outerphy_attr_array.outerphy_name:phy_88E1322>
ERROR:param-><index:3><outerphy->outerphy_name:0x8af56d9>
<outerphy_attr_array.outerphy_name:phy_zx5201>
ERROR:param-><index:4><outerphy->outerphy_name:0x8af56d9>
<outerphy_attr_array.outerphy_name:phy_YT8821>
ddd
ddERROR:param-><index:5><outerphy->outerphy_name:0x8af56d9>
<outerphy_attr_array.outerphy_name:phy_RTL8226>
0 serdes option is 0
xmac0 is used
ERROR: Can't get outerphy_desc! Plz check about it!
ERROR: Can't get outerphy_desc! Plz check about it!
mac 0 link down
mac 1 link down
mac 2 link down
mac 3 link down
mac 4 link down
1 idm_ddr_base is 00000000b5d0cd85, phy addr is 0x80b23000
ddr size(0xee5000), idm used(0xee5000)
irqsg_idm_irq_mask_conf(0x71ffbfb)
111000111111111101111111011
irqsg_idm_irq_mask_conf(0x200000)
000001000000000000000000000
irqsg_idm_irq_mask_conf(0x400000)
000010000000000000000000000
irqsg_idm_irq_mask_conf(0x800404)
000100000000000010000000100
idm net init ok
nppt init end. ret = 0
init np_reg module
init np start
creat ddr space for bmu.
:ddr space(start:0x81a08000, size:0x1f60000) for bmu
pp_bppe_pool_init:BPPE_PA_BASE = 0x81a08000
pp_bppe_pool_init: bppe_va_addr =0x00000000a5818b11, BPPE_PA_BASE = 0x81a08000
tcont mode is 0
ddr space(start:0x83968000, size:0x400000) for hash table
version: 0x0001.0x0108.0x31ba6a03
tm acl init, ret = 0
mul_ip_table_busy_lock!
real_port: 15 real_queue_id:419
real_port: 15 real_queue_id:419
real_port: 15 real_queue_id:419
real_port: 15 real_queue_id:419
real_port: 15 real_queue_id:419
real_port: 15 real_queue_id:419
real_port: 15 real_queue_id:419
real_port: 15 real_queue_id:419
user table init success.
Low power buf start phy addr:virtual addr:00000000ed718e3c
create xemac_task_thread ok!
init low power success
init np success
NP Module SYS FS Init ended successfully =
init np_reg module success
success!
success!
ipsec init enter
ipsec hardware driver will not init because the devicetree of ipsec is unavailab le.
pon_sta_filter_oam_omci_cfg_set enter
pon_sta_filter_oam_omci_cfg_set end
current chip is ZX279133
############################# 133
init_module: umod=000000006c23bced, len=8792, uargs=000000007b29053c
zx_ponreg_133: magic '4.19.136 SMP mod_unload aarch64' should be '4.19.136+ SMP mod_unload aarch64'
jffs2: notice: (945) check_node_data: wrong data CRC in data node at 0x02b4eef0: read 0xee37cbcd, calculated 0xd068f8d.
qupengchao : symname is init_module
register fpga driver success, major=222
jffs2: notice: (945) check_node_data: wrong data CRC in data node at 0x02b54bf8: read 0x68c47d75, calculated 0x8cb69dd4.
init_module: umod=000000006c23bced, len=92416, uargs=000000007b29053c
qupengchao : symname is init_module
init_module: umod=000000006c23bced, len=5736, uargs=000000007b29053c
qupengchao : symname is init_module
region_code_init region_code:307, ret:0
init_module: umod=000000006c23bced, len=84992, uargs=000000007b29053c
qupengchao : symname is init_module
qupengchao : pon0 create success
11930:23:16 SIOCGIFFLAGS
init_module: umod=000000006c23bced, len=42384, uargs=000000007b29053c
qupengchao : symname is init_module
iprt_data_init success!
init_module: umod=0000000067964c36, len=169288, uargs=000000007b29053c
qupengchao : symname is init_module
init_module: umod=000000006c23bced, len=48552, uargs=000000007b29053c
dqupengchao : symname is init_module
ethdriver_init....
g_mii_dev_namesw
g_mii_dev_namepon
init_module: umod=00000000669be306, len=284952, uargs=000000007b29053c
qupengchao : symname is init_module
init_module: umod=0000000098178684, len=853280, uargs=000000007b29053c
qupengchao : symname is init_module
Init switch module
d cur_bit_offset(8192) is out of range
para error
cur_bit_offset(8192) is out of range
para error
port(64) set table ▒▒#_attr_name▒▒(0) fail
set fail
init port route mode fail
sw_cap.SW_ETH_UNI = 4.
sw_cap.SW_ETH_UNI = 1.
sw_cap.SW_ETH_UNI = 2.
sw_cap.SW_ETH_UNI = 3.
zy uni num:4
zy switch all port count:7
switch config 9132 GPONmode!
set cpu queue rate limit to 4000pps
reg hff
reg ipsec up hff
enter woe_reg_register!
success!
create stati1_turn_thread success.
Init switch module Success
input:upModeInfo is 0x40,new_upmode is 0x40,new_lanup_po rt is 0 new_wlanup_port is 0
done
init_module: umod=0000000033815f7d, len=308856, uargs=000000007b29053c
zte_xgpon: magic '4.19.136 SMP mod_unload aarch64' should be '4.19.136+ SMP mod_ unload aarch64'
dqupengchao : symname is init_module
insmod gponsdk_dev
XGMAC: VirAddr:0x0000000019906458
pon mode is xg
init_module: umod=000000006c23bced, len=66504, uargs=000000007b29053c
qupengchao : symname is init_module
gpon_Init ok
No need to load RTL switch chip driver
init_module: umod=000000006c23bced, len=47496, uargs=000000007b29053c
qupengchao : symname is init_module
GN28L95 read table 0xFF chipname-register success,chipname=0xFF.
UX3360 read table 0x86 register(0x80~0x85) success,chipname=.
UX3361 read table 0x87 register(0x80~0x85) success,chipname=UX33631.
bsp_mcu_eeprom_mode_select read table register success.
judge chip select mcu(0x*0) or eeprom(0x*1) mode ! count=0, judge_reg=0xFF.
bsp_chip_probe count=0, r_data=0x00.
UX3361 found.
bsp_UX3361_probe 0x51 success!
Optical select UX3361 mode is MCU.
vendor name = ZTE_XGPON1ASY
temp_PN = ▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒
optical PN(0x60) = ▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒
optical PN(0x28) = GN28L95
dinit_module: umod=000000006c23bced, len=34880, uargs=000000007b29053c
qupengchao : symname is init_module
udpwatchd inited!
kudpinited!
init_module: umod=00000000e819560c, len=332416, uargs=000000007b29053c
dsp_dev: magic '4.19.136 SMP preempt mod_unload ARMv7 p2v8 ' should be '4.19.136 + SMP mod_unload aarch64'
voip_codec: module PLT section(s) missing
qupengchao : symname is init_module
Init codec v2.5(2019-09-18)!
init_module: umod=00000000ed2969d6, len=161840, uargs=000000007b29053c
qupengchao : symname is init_module
P_2833: Setup 0
DSP device setup OK!
dsp binding cpu:1
dsp softirq
init_module: umod=000000006c23bced, len=24536, uargs=000000007b29053c
qupengchao : symname is init_module
G_XGSPON_MODE is 0(XGPON)
init_module: umod=000000006c23bced, len=27960, uargs=000000007b29053c
qupengchao : symname is init_module
dGN28L95 read table 0xFF chipname-register success,chipname=0xFF.
UX3360 read table 0x86 register(0x80~0x85) success,chipname=.
UX3361 read table 0x87 register(0x80~0x85) success,chipname=UX33631.
bob chip select is UX3361.
bsp_mcu_eeprom_mode_select read table register success.
judge chip select mcu(0x*0) or eeprom(0x*1) mode ! count=0, judge_reg=0xFF.
dbsp_chip_probe count=0, r_data=0x00.
UX3361 found.
bob select UX3361 mode is MCU.
Kmodule GN28L95.ko insmod successfully !
bobtest create /userconfig/GN28L95_datas_backup/BOB_CHIP_SELECT
Bob chip_type: UX3361
bobtest GET_BOB_CHIP_SELECT OK
bobtest create /tmp/UX3361_MCU_MODE
Bob chip_type: UX3361
bobtest GET_UX3361_MCU_MODE OK
WLAN_TMP_MD5SUM_VALUE=717e1cd37329309ec465387e99e04245
USERCONFIG_TMP_MD5SUM_VALUE=717e1cd37329309ec465387e99e04245
dWLAN_NOW_MD5SUM_VALUE=717e1cd37329309ec465387e99e04245
USERCONFIG_NOW_MD5SUM_VALUE=717e1cd37329309ec465387e99e04245
WLAN_TMP_MD5SUM_VALUE == USERCONFIG_TMP_MD5SUM_VALUE
WLAN_NOW_MD5SUM_VALUE == USERCONFIG_NOW_MD5SUM_VALUE, everything is OK, leave!
Bob chip_type: UX3361
bobtest write_all_datas_to_UX3361,load data from flash to UX3361!
bobtest table_select_UX3361 128 OK
bobtest reply_read_reg 162 183 0
dbobtest table_select_UX3361 128 OK
bobtest write_data_to_UX3361 162 0 123
dbobtest table_select_UX3361 129 OK
bobtest write_data_to_UX3361 162 128 107
dbobtest table_select_UX3361 130 OK
bobtest write_data_to_UX3361 162 128 107
bobtest table_select_UX3361 131 OK
bobtest write_data_to_UX3361 162 128 107
dbobtest table_select_UX3361 132 OK
bobtest write_data_to_UX3361 162 128 128
dbobtest table_select_UX3361 133 OK
bobtest write_data_to_UX3361 162 128 128
ddbobtest table_select_UX3361 134 OK
bobtest write_data_to_UX3361 162 128 43
bobtest table_select_UX3361 128 OK
bobtest write_data_to_UX3361 162 128 128
dbobtest table_select_UX3361 128 OK
bobtest write_all_datas_to_UX3361 duration: 1.237986
write_all_datas_to_UX3361 finish!!!
exit factory mode!
init_module: umod=000000006c23bced, len=33528, uargs=000000007b29053c
dqupengchao : symname is init_module
success : download_init 1343
init_module: umod=000000006c23bced, len=38288, uargs=000000007b29053c
qupengchao : symname is init_module
:upload init enter
:upload init sucess
IPv6: ADDRCONF(NETDEV_UP): tunTX: link is not ready
IPv6: ADDRCONF(NETDEV_UP): tapTX: link is not ready
Memory mapped at address 0xf7b2f000.
Value at address 0x19140240 (0xf7b2f240): 0x0
Written 0x1; readback 0x1
sky:loop check_and_reinit phy
region code:307
region name:Beijing
dsky: lan:, pots, wifi
sky: could not found config xml
sky: try
sky: found config xml
USER_CFG is same as ETC_CFG, donot need copy
===================================================================
Database default setting is
chown: /webpages: No such file or directory
dFailed to set capabilities on file '/bin/ipsec/starter': No such file or direct ory
Failed to set capabilities on file '/bin/ipsec/charon': No such file or director y
dmodel:
SK-D847N
dsoftversion:
V2.0.0
dhardversion:
V2.0
dfull_version:
SK-D847N_V2.0.0_SVN317966_VID002_DQ307
*****************pc start********************
*****************echo 5000 > /proc/sys/vm/min_free_kbytes********************
11930:23:20 clib_scan_wlan_chi p cChipNum=2
OSS: start cspd
dchmod: /usr/local/osgi: Read-only file system
/wlan/age.txt exist
11930:23:21 reg_fwsfs_mgr_pdt _cb melon
11930:23:21 The Dss' lpMsg is nu ll.
11930:23:21 ====>Mtk_I nit_7916!
11930:23:21 wlan_chip[ 3].Init790a_7906!
11930:23:21 rlk_wlan _adapter_main, g_Wlan_Card_Max=2
11930:23:21 OSGI_PROXY_PI D tUsbDevInfoListShmid sinit_module: umod=000000006c23bced, len=9768, uargs=0000 00007b29053c
hmget init ok!
dbg: runing cmd[cat /proqupengchao : symname is init_module
c/capability/boardtype | sed -n 1p | awk -F ": " '{print $2}']
start.
11930:23:21 mx_de bug schedule_reboot_init
dbg: runing cmd
obj_str=MT7916_EEPROM_tdy09.bin
11930:23:21 zxicDbXMLCreateTb lLoad tblname(EASYMESHCONFIG) ptViewParamFun is NULL error.
11930:23:21 zxicDbXMLCreateTb lLoad tblname(UpgFirReboot) ptViewParamFun is NULL error.
11930:23:21 zxicDbXMLCreateTb lLoad tblname(LedTime) ptViewParamFun is NULL error.
11930:23:21 both /wl an/MT7916_EEPROM.bin and /tagparam/MT7916_EEPROM_bak.bin exist
11930:23:21 ENTER ch eckAndSetEepromFileMd5_7916(133)
11930:23:21 Get_Wifi_Type:e_wifi _type=0x20
SKY_MODEL_NAME has setted, leave!
11930:23:21 pon not found.
11930:23:21 Get pon port faile d!
11930:23:21 ups not found.
11930:23:21 GetUpsDevNum failed !
11930:23:21 sky:init telnetcfg, regi on is default
11930:23:22 MobileAppInfo.BooTy pe set to 1
11930:23:22 macbin d init option60 msg queue success
11930:23:22 reg_fwlevel_mg r_pdt_cb melon
11930:23:23 ************ ENTER md5_sum_cmp(6592) **************
11930:23:23 md5_sum_cmp
11930:23:23 open /tagpar am/MT7916_EEPROM_MD5.txt fail!
11930:23:23 *<3000000005 >11930:23:23 dev_get_by _name error !
***********ENTER md5_sum_cmp(6592) *ethdrv_dev_ioctl,brdev_set.port_id 0 ,brde v_set.name eth0 ,brdev_set.flag 0
*************
11930:23:23 md5_sum_cmp
11930:23:23 open /tagpar am/MT7916_EEPROM_bak_MD5.txt fail!
11930:23:23 md5_maste r_flag=-1, md5_backup_flag=-1
11930:23:23 /wlan/MT7 916_EEPROM.bin and /tagparam/MT7916_EEPROM_bak.bin md5 are not verify ok.
11930:23:23 RunProcess process Event dwUsedTicks
get regioncode 33010000
11930:23:23 now i n func si_get_province_map
11930:23:23 Provi nce:BEJ
11930:23:23 The Dss' lpMsg is nu ll.
11930:23:23 si_db_qry_defa ult_rt: no default RT
11930:23:23 si_db_qry_defau lt_rt6: no default RT
UpMod close uart!
页:
[1]