天邑1006g..拆机ttl无法中断CFE
本帖最后由 12152 于 2023-1-14 16:10 编辑ttl接线没有问题，可以看到信息滚动，按ctrl+c无法中断进入CFE..大佬们可有啥办法进入
Default DTB file name :
Board Id : TY968560CTW6
Number of MAC Addresses (1-64) : 11
Base MAC Address : 44:43:d5:29:0b:d4
PSI Size (1-512) KBytes : 24
Enable Backup PSI : 1
System Log Size (0-256) KBytes : 0
Auxillary File System Size Percent: 0
GPON Serial Number : "SCTYB4AAFF50"
GPON Password : " "
RNR_TBLS memory allocation (8-13) (MB) : 8
FPM_POOL memory allocation (MB) : 32
DHD 0 memory allocation (MB) : 0
DHD 1 memory allocation (MB) : 0
DHD 2 memory allocation (MB) : 0
WLan Feature : 0x00
Voice Board Configuration (0-4) : NOSLIC
Partition 1 Size (MB) : 159M
Partition 2 Size (MB) : 0M
Partition 3 Size (MB) : 1M
Partition 4 Size (MB) (Data) : 4M
*** Press 'ty' to stop auto run (1 seconds) ***
Auto run second count down: 1
好吧按ty中断成功，GPON SN改吧。GPON password也改了，还是连不上，进系统发现LOID还在，咋把这个去掉呢。。 Available commands:
otpcfg Reading/fusing potp/sotp bits
unimac_stats Show UNIMAC port statistics
set_dump Dump all recieved packets on active port
net_stats Get network ports status
vrpd View Ring packet descriptor
sar Show available Runner to CPU rings
erase_misc_parti Erase misc partition
x Change extra partitions size
find Find string in NAND
comp Compare NAND blocks
bb Find NAND flipped bits by comparing a read with and without ECC
fb Find NAND bad blocks
rn Read NAND contents along with spare area with ECC off
dn Dump NAND contents along with spare area
phy Set memory or registers.
meminfo Display CFE System Memory
kernp Updates extra bootloader parameter for kernel. To end input enter // consecutively at any time then press <enter>
sm Set memory or registers.
swrp Enumeratepower supplies
swrd Dump SWREG
swrw Write SWREG
swrr Read SWREG
db Dump bytes.
dh Dump half-words.
dw Dump words.
ddw Dump dwords.
w Write the whole image start from beginning of the flash
e Erase NAND flash
wp Write pmc (previously loaded through JTAG to flash block 0.
ws Write whole image (priviously loaded by kermit or JTAG) to flash .
ba set linux kernel boot argument
ldt load device tree blob from tftp server.
go goto and execute from specefic address.
loadb load binary via network or kermit protocol.
r Run program from flash image or from host depending on flags
p Print boot line and board parameter info
c Change booline parameters
i Erase persistent storage data
ddr Change board DDR config
a Change board AFE ID
b Change board parameters
reset Reset the board
pmdio Pseudo MDIO access for external switches.
spi Legacy SPI access of external switch.
pmclog pmclog
pmc pmc cmd
closeavs pmc close avs cmd
force override chipid check for images.
help Obtain help for CFE commands
For more information about a command, enter 'help command-name'
*** command status = 0 b项里面没有修改loid的位置。。。。哪位大神给瞅瞅哪个可以改loid认证 12152 发表于 2023-1-15 12:23
好吧按ty中断成功，GPON SN改吧。GPON password也改了，还是连不上，进系统发现LOID还在，咋把这个去掉呢。 ...
清除nvram zhjook 发表于 2023-1-15 16:48
清除nvram
这个咋清除
为啥ttl,我帮你搞 dzxhyd 加V 大佬！求网络备份固件 uin 发表于 2023-1-17 11:18
大佬！求网络备份固件
等晚上我试试看能备份出来不
页:
[1]
2