chenwu0625 发表于 2017-11-8 12:40:54

求助，怎么处理改错board了，一直循环求停止的方法

HW module is installed
ifconfig eth0 hw ether D4:B1:10:E7:EC:77
Loading the EchoLife WAP modules: LDSP
COMMON For LDSP Install Successfully...
GPIO For LDSP Install Successfully...
HIGHWAY For LDSP Install Successfully...
------ SOC is 5115 H PILOT ------
<ldsp>board version is 19
<ldsp>pcb version is 0
<ldsp>orig board version is 3
CHIPADP-SD5115 BASIC For LDSP Install Successfully...
CHIPADP-SD5115 EXT For LDSP Install Successfully...
I2C For LDSP Install Successfully...
LSW L2 For LDSP Install Successfully...
LSW L3 For LDSP Install Successfully...
DEV For LDSP Install Successfully...
:ae_chip=2,ae_chip=255,ae_chip=255,ae_chip=0
:board_ver=19,pcb_ver=0
:Can not find pd file in /etc/wap/dm.cfg/pd_relation.cfg.
Kernel panic - not syncing: Get product config file Error!
[<c0031da0>] (unwind_backtrace+0x0/0xfc) from [<c02d8810>] (panic+0x60/0xd8)
[<c02d8810>] (panic+0x60/0xd8) from [<bf1a2314>] (hw_dm_pd_static_attr_init+0xf0/0x124 )
[<bf1a2314>] (hw_dm_pd_static_attr_init+0xf0/0x124 ) from [<bf1a52a4>] (hw_dm_pd_attr_init+0x2c/0xe4 )
[<bf1a52a4>] (hw_dm_pd_attr_init+0x2c/0xe4 ) from [<bf19e08c>] (hw_dm_init_data+0x64/0x12c )
[<bf19e08c>] (hw_dm_init_data+0x64/0x12c ) from [<bf3d77b8>] (init_module+0xd0/0x2c0 )
[<bf3d77b8>] (init_module+0xd0/0x2c0 ) from [<c002b5b4>] (do_one_initcall+0x30/0x1c0)
[<c002b5b4>] (do_one_initcall+0x30/0x1c0) from [<c0073ba8>] (sys_init_module+0xc4/0x1f8)
[<c0073ba8>] (sys_init_module+0xc4/0x1f8) from [<c002c0e0>] (ret_fast_syscall+0x0/0x30)
Rebooting in 3 seconds..

irc163 发表于 2017-11-8 14:28:44

这个一般的无法停止，上编程器修吧

fnto 发表于 2017-11-8 14:40:50

什么猫？？///

irc163 发表于 2017-11-8 16:36:03

fnto 发表于 2017-11-8 14:40
什么猫？？///

------ SOC is 5115 H PILOT ------
<ldsp>board version is 19
<ldsp>pcb version is 0
<ldsp>orig board version is 3

这个看都看的出来

fnto 发表于 2017-11-8 17:59:12

19可能是他改错后的id呢。

fnto 发表于 2017-11-8 18:00:21

3对应啥型号？

chenwu0625 发表于 2017-11-8 23:46:33

irc163 发表于 2017-11-8 08:36
------ SOC is 5115 H PILOT ------
board version is 19
pcb version is 0


我问怎么修复 我也晓得错了

yhy809980 发表于 2017-11-13 22:07:46

我的和你的情况一样，我的是8245C2的光猫，修砖刷的8120C的包，也是无限重启，你搞定了吗？我已经买了相同的路由器准备上编程器了

chenwu0625 发表于 2017-11-15 11:13:53

yhy809980 发表于 2017-11-13 14:07
我的和你的情况一样，我的是8245C2的光猫，修砖刷的8120C的包，也是无限重启，你搞定了吗？我已经买了相同 ...

没有 你有编程器把固件 读出来 我给你改了 刷回去 就好我没编程器非要 nand flash 你可以加我微信chenwu150532648 备注 adsl论坛
页: [1]
查看完整版本: 求助，怎么处理改错board了，一直循环求停止的方法