|
|
楼主 |
发表于 2013-9-26 22:19:19
|
显示全部楼层
0 {4 u+ I$ D1 T" R+ wwan 设置之前,要新建一个 atm , 勾选另一个path1 (0和1,之前的拨号默认是path0) 其他设置一样,之后就可以在wan 中添加一个桥接了( a5 p0 Q% ^) W& g" z
; J# X, t" v4 g% L5 I8 cATM PVC Configuration9 t9 t( V% \; m u% ^
This screen allows you to configure an ATM PVC identifier (VPI and VCI), select DSL latency, select a service category.
9 G' O* d& J4 c% U d
1 V+ b. T7 h" W* u: i" x$ \| VPI: [0-255] | | | VCI: [32-65535] | |
1 }5 q3 u5 w9 h$ o; N' o1 L( y/ x| Select DSL Latency | | Path0 | | Path1 |
8 ]2 O6 p- u. d( d% n
| Select DSL Link Type (EoA is for PPPoE, IPoE, and Bridge.) | | EoA | | PPPoA | | IPoA |
, N, X7 T; m% b( V3 u" H: L% c
| Select Connection Mode | | Default Mode - Single service over one connection | | VLAN MUX Mode - Multiple Vlan service over one connection |
5 w$ G5 ^4 _6 o* {
) y! F- B2 w) H9 n! _. A* f
' D2 V6 M& } k% n! ~1 W& m, l$ K) i7 ?: b' z
) c7 B: b6 ~# M# M, X, k- U" ?; v" L K& [
7 _7 {8 w$ x# _. k
x) {; U! [3 |. n2 j2 \& ]DSL ATM Interface Configuration$ B8 k; @5 \0 m3 k; M# F8 a
6 L4 d' |' f2 pChoose Add, or Remove to configure DSL ATM interfaces.
' p3 O# b D- }$ l% L- ]% T* w, I; m
; y2 u, a$ [; Q! N| Interface | Vpi | Vci | DSL Latency | Category | Link Type | Connection Mode | IP QoS | Scheduler Alg | Queue Weight | Group Precedence | Remove | | atm0 | 0 | 35 | Path0 | UBR | EoA | DefaultMode | Enabled | SP | | | | | atm1 | 0 | 35 | Path1 | UBR | EoA | DefaultMode | Enabled | SP | | | |
( n* z6 F' E+ n0 m 7 D4 V0 {/ C; Z2 e% J* A" S
6 I) m& q. B \! }* V8 ~$ e
9 E+ ~3 A7 V$ {3 u& M8 J- U( j1 I7 [6 P; G) k' a
2 a& T) I$ P ~; ?! c
WAN Service Interface Configuration' ?& M: J2 K& i/ C
0 `6 |' T( t4 _/ n6 g8 w
Select a layer 2 interface for this service Note: For ATM interface, the descriptor string is (portId_vpi_vci)
$ D% u4 q; a+ ?+ x0 `Where portId=0 --> DSL Latency PATH0
+ I9 Y4 O; ~/ h' @portId=1 --> DSL Latency PATH19 y7 R, V8 M( J/ _* Z7 \
portId=4 --> DSL Latency PATH0&1
4 w+ B9 p/ D4 _/ a
' N8 A4 s" {- y3 H( p4 A3 N) [# M3 N% q! Y. q+ R
3 D3 N7 A3 L! I2 h, A
& j: P+ H+ |% m# X1 }* S
4 ~9 h* v% E" S5 J) M- e. t
+ t8 ~- D& ^1 ~4 SWAN Service Configuration- G% X/ J. j! s% ^# W, t) V* L
4 ]2 [* n, o- s `% p( j+ U2 Z' P7 E, j
| Select WAN service type: | | PPP over Ethernet (PPPoE) | | IP over Ethernet | | Bridging |
4 n& t1 X- q I
& Z) X S8 Q7 O| Enter Service Description: |
# A+ u& ?0 c& n0 e
) S( c) j+ F3 p C |
- [3 o8 J; k! @$ _
* _" U" t8 L$ O' W然后在组设置里边添加iptv的 group 和绑定的端口0 Q/ g% F, m v; m5 Y: {% a; I
% l5 n6 E# h& b$ g, F/ [* Q4 T
# m; B, }! i9 v8 j5 \0 ]0 f
Interface Grouping -- A maximum 16 entries can be configured" r$ x5 j7 s; m
9 N3 y# ]3 u' ]0 e# eInterface Grouping supports multiple ports to PVC and bridging groups. Each group will perform as an independent network. To support this feature, you must create mapping groups with appropriate LAN and WAN interfaces using the Add button. The Remove button will remove the grouping and add the ungrouped interfaces to the Default group. Only the default group has IP interface.
7 }' g2 v8 z- R8 T( I8 v) h* X D! ^4 _% o
6 Q2 i" @3 h& h6 c9 d7 u( G
U' } S. K) M, O6 _: L& k3 H
| Group Name | Remove | WAN Interface | LAN Interfaces | DHCP Vendor IDs | | Default | | ppp0 | LAN4 | | | LAN3 | | | LAN1 | | | wlan0 | | | IPTV | | atm1 | LAN2 | |
4 E. a9 i: G. g3 Y
7 `: B. _/ d3 a! ?7 F# @: a
0 D* Q" ^8 O4 ]. x9 O, v$ U, p: \- g; ^0 J$ @, ~8 [
, g( c% _1 G2 r* y: z, e. w [- f- u- ] S p
|
|
粤公网安备44152102000001号 
发表于 2013-9-5 21:14:52
