找回密码
 注册

QQ登录

只需一步,快速开始

查看: 16891|回复: 7

HG8245 变砖,请高人指导,看能否修复

[复制链接]
发表于 2014-1-9 12:13:15 | 显示全部楼层 |阅读模式
由于修改了HW_boradinfo.xml文件,可能修改的不对,导致192.168.1.1,telnet都进不去了,现在com口能连上,但出现以下状况,不知如何是好,请高人指导,非常感谢!
/*..............
System start ...
.............*/
U-Boot 1.1.4 (Jul 31 2013 - 16:25:21)
U-Boot code: 90500000 -> 9051FC94  BSS: -> 9054658C
RAM Configuration:
Bank #0: 90000000 64 MB
Flash: 16 MB
*** Warning - bad CRC, using default environment
In:    serial
Out:   serial
Err:   serial
Extend LSW IS AR8316
Initialize broadcast table ... ok
CPURTx Driver For Pilot <Board-A>!
### JFFS2 loading 'fsok' to 0x904bfe84
Scanning JFFS2 FS: . done.
### JFFS2 load complete: 2 bytes loaded to 0x904bfe84
No board type file!
ui_board_id = 1
[main.c__3719]::Magic1:0x40034620, magic2 0xa5081c2a, count 1218121249, flag 550015366, MainAreaOK 1248198801, slaveAreaOK 1010992988
[main.c_3784]Start from normal system!
Magic1:0x5a5a5a5a, magic2 0xa5a5a5a5, count 0, flag 0
Addr[0]:0x0,Addr[1]:0x40000,Addr[2]:0x41000,Addr[3]:0x60000,Addr[4]:0x1e0000,Addr[5]:0xae0000,Addr[6]:0xe60000
Start copy data from 0x201e0054 to 0x91000000 with sizeof 0x0086d040 ....................Done!
Start system with ram disk and set bootcmd to
BootArgs:noalign mem=50M console=ttyAMA0,115200 root=/dev/ram0 rootfstype=squashfs mtdparts=hisilicon:0x40000(boot)ro,0x1000(flashcfg)ro,0x1f000(syspara)ro,0x180000(krnl)ro,0x8fffac@0x1e0054(rootfs)ro,0x248fe0@0xc17020(minisystem)ro,0x180000(jffs2cfg),-(reserved) user_debug=0x1f panic=1
U-boot Start from NORMAL Mode !
## Booting image at 20060054 ...
   Image Name:   Linux-2.6.21.7-hrt1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1483004 Bytes =  1.4 MB
   Load Address: 90008000
   Entry Point:  90008000
   Loading Kernel Image ... OK
## Loading Ramdisk Image at 91000000 ...
   Image Name:   squashfs
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    8835072 Bytes =  8.4 MB
   Load Address: 00000000
   Entry Point:  00000000
Starting kernel ...
Uncompressing Linux............................................................................................. done, booting the kernel.
Kernel Early-Debug on Level 0
iotable information:
virtual: 4093640704physical: 262144  length: 4096    type: 0
virtual: 4145283072physical: 90432  length: 4096    type: 0
virtual: 4145295360physical: 90435  length: 4096    type: 0
virtual: 4145340416physical: 90446  length: 4096    type: 0
virtual: 4145344512physical: 90447  length: 4096    type: 0
virtual: 4093706240physical: 262160  length: 4096    type: 0
virtual: 4093771776physical: 262176  length: 4096    type: 0
virtual: 4145307648physical: 90438  length: 32768    type: 0
virtual: 4145287168physical: 90433  length: 4096    type: 0
virtual: 4145348608physical: 90448  length: 4096    type: 0
virtual: 4076863488physical: 196608  length: 4096    type: 0
virtual: 4145291264physical: 90434  length: 4096    type: 0
virtual: 4145299456physical: 90436  length: 4096    type: 0
virtual: 4145303552physical: 90437  length: 4096    type: 0
hisilicon_map_io        281     [arch/arm/mach-sd5113_v100_p01/core.c]
hisilicon_init_irq      108     [arch/arm/mach-sd5113_v100_p01/core.c]
hisilicon_timer_init    228     [arch/arm/mach-sd5113_v100_p01/systimer.c]
hi_kernel_wdt_init      216     [arch/arm/mach-sd5113_v100_p01/hi_drv_wdt.c]
hisilicon_init_machine  175     [arch/arm/mach-sd5113_v100_p01/core.c]
hi_kernel_pci_preinit   390     [arch/arm/mach-sd5113_v100_p01/hi_pci.c]
pci clock is on!
hi_kernel_pci_postinit  481     [arch/arm/mach-sd5113_v100_p01/hi_pci.c]
hi_kernel_pci_map_irq   367     [arch/arm/mach-sd5113_v100_p01/hi_pci.c]
Linux version 2.6.21.7-hrt1 (xiongyao@server28) (gcc version 4.1.2 (Wind River Linux Sourcery G++ 4.1-84)) #2 Fri Jun 24 13:57:01 CST 2011
CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv6TEJ), cr=00c5387f
Machine: SD5113-V100-PILOT-B01
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIPT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists.  Total pages: 12700
Kernel command line: noalign mem=50M console=ttyAMA0,115200 root=/dev/ram0 rootfstype=squashfs mtdparts=hisilicon:0x40000(boot)ro,0x1000(flashcfg)ro,0x1f000(syspara)ro,0x180000(krnl)ro,0x8fffac@0x1e0054(rootfs)ro,0x248fe0@0xc17020(minisystem)ro,0x180000(jffs2cfg),-(reserved) user_debug=0x1f panic=1
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 50MB = 50MB total
Memory: 38972KB available (2676K code, 233K data, 108K init)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Hisilicon clock system V0.01
[clk_register, 244]     AHBCLK
[clk_register, 244]     ARMCORECLK
[clk_register, 244]     UARTCLK
PCI: device 0000:00:03.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:04.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:05.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:06.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:07.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:08.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:09.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:0a.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:0b.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:0c.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:0d.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:0e.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:0f.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:10.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:11.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:12.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:13.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:14.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:15.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:16.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:17.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:18.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:19.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:1a.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:1b.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:1c.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:1d.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:1e.0 has unknown header type 1c, ignoring.
PCI: device 0000:00:1f.0 has unknown header type 1c, ignoring.
PCI: bus0: Fast back to back transfers enabled
istatus and imask 16777216
istatus and imask 0
map irq: slot 0, pin 1, devslot 2, irq: 21
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 8628K
Registering GDB sysrq handler
squashfs: version 3.4 (2008/08/26) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: dw  uart driver
dev:f2: ttyAMA0 at MMIO map 0x1614f000 mem 0xf714f000 (irq = 17) is a AMBA/DW
dev:f1: ttyAMA1 at MMIO map 0x1614e000 mem 0xf714e000 (irq = 16) is a AMBA/DW
RAMDISK driver initialized: 4 RAM disks of 23000K size 1024 blocksize
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
CSLIP: code copyright 1989 Regents of the University of California.
SLIP linefill/keepalive option.
netconsole: not configured, aborting
Start to set chip MaxBufWriteSize.
Not find New chip.
hisilicon: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
hisilicon: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Hisilicon flash: registering whole flash at once as master MTD
8 cmdlinepart partitions found on MTD device hisilicon
Creating 8 MTD partitions on "hisilicon":
0x00000000-0x00040000 : "boot"
0x00040000-0x00041000 : "flashcfg"
0x00041000-0x00060000 : "syspara"
0x00060000-0x001e0000 : "krnl"
0x001e0054-0x00ae0000 : "rootfs"
0x00c17020-0x00e60000 : "minisystem"
0x00e60000-0x00fe0000 : "jffs2cfg"
0x00fe0000-0x01000000 : "reserved"
usb clock is on!
h2v100-ehci h2v100-ehci.0: h2v100-ehci
h2v100-ehci h2v100-ehci.0: new USB bus registered, assigned bus number 1
h2v100-ehci h2v100-ehci.0: irq 23, io mem 0x40010000
h2v100-ehci h2v100-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
h2v100-ohci h2v100-ohci.0: h2v100-ohci
h2v100-ohci h2v100-ohci.0: new USB bus registered, assigned bus number 2
h2v100-ohci h2v100-ohci.0: irq 24, io mem 0x40020000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Netfilter messages via NETLINK v0.30.
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
RAMDISK: squashfs filesystem found at block 0, block number 8626
RAMDISK: Loading 8626KiB [1 disk] into ram disk... done.
VFS: Mounted root (squashfs filesystem) readonly.
Freeing init memory: 108K
                        -=#  DOPRA LINUX 1.0  #=-
                        -=#  EchoLife WAP 0.1  #=-
                        -=#  Huawei Technologies Co., Ltd #=-
mount file system
Loading the kernel modules:
Loading module: nf_conntrack
nf_conntrack version 0.5.0 (400 buckets, 3200 max)
Loading module: nf_conntrack_ftp
Loading module: nf_conntrack_tftp
Loading module: nf_nat
Loading module: nf_nat_ftp
Loading module: nf_nat_tftp
Making device instances:
Setting console log message level:
Setting hostname:
Settingup the sysctl configurations:
Setting up interface lo:
Running local startup scripts.
*************************************
--==   Welcome To EchoLife WAP   ==--
*************************************
WAP Ver:V100R002C04SPC101B115
WAP Timestamp:2011/08/10 10:50:33
*************************************
Rootfs time stamp:2011-08-10_10:56:55
Mount the JFFS2 file system:
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
fuse init (API version 7.8)
User init start......
Loading the SD5113V100 modules:
ETH install success!
SD511X  DP  V1.0 is installed !
SD511x IOCTL_DP  V1.0 is installed
SD511x MDIO ID V1.0 is installed
SD511x GPIO VERSION 1.0 is installed
SD511x GPIO_INT ID 1.0 is installed
SD511x I2C ID V1.0 is installed
SD511x TIMER ID V1.0 is installed
SD511X SPI ID v1.0 is installed
SD511X  SYSCTL  V1.0 is installed
SD511x UART ID V1.0 is installed
SD5113 DMA ID V1.0 is installed
<6>
SD511X HW  ID v1.0 is installed
SD511x EXT_INT ID 1.0 is installed
SD511x IOCTL_SYSCTL  V1.0 is installed
ifconfig eth0 hw ether 08:19:A6:C4:48:30
Loading the EchoLife WAP modules: LDSP
SSP For LDSP Install Successfully...
HLP For LDSP Install Successfully...
CHIPADP-PHY For LDSP Install Successfully...
CHIPADP-SD5113 For LDSP Install Successfully...
GPIO For LDSP Install Successfully...
HIGHWAY For LDSP Install Successfully...
I2C For LDSP Install Successfully...
MDIO For LDSP Install Successfully...
CHIPADP-AR8316 LSW For LDSP Install Successfully...
SPI For LDSP Install Successfully...
UART For LDSP Install Successfully...
BATTERY For LDSP Install Successfully...
PLOAM For LDSP Install Successfully...
GMAC For LDSP Install Successfully...
KEY For LDSP Install Successfully...
LSW For LDSP Install Successfully...
LED For LDSP Install Successfully...
OPTIC For LDSP Install Successfully...
RF For LDSP Install Successfully...
DEV For LDSP Install Successfully...
USB For LDSP Install Successfully...
HW_KER_BBSP_COMMON_HLE_SET_DEBUG_E:13Common HLP For BBSP Install Successfully...
FLOW For BBSP Install Successfully...
VETH For LDSP Install Successfully...
WIFI For BBSP Install Successfully...
PDLV For BBSP Install Successfully...
Dosflt For BBSP Install Successfully...
EMAC For LDSP Install Successfully...
MPCP For LDSP Install Successfully...
Loading DSP temporary modules:
linux kernel dopra is installed!
dsp sdk  insmod success!
DSP For LDSP Install Successfully...
Loading the EchoLife WAP modules: BBSP
hw_pkt_tunnel Install Successfully...
hw_acl init success
hw_dhcp Install Successfully...
NAPT For BBSP Install Successfully...
hw_igmp_kernel Install Successfully...
CODEC For LDSP Install Successfully...
hw_ringchk_kernel Install Successfully...
hw_ethoam_kernel Install Successfully...
hw_pppoe Install Successfully...
Portal For BBSP Install Successfully...
install success
ssmp bbsp vspa igmp amp tran_console cwmp apm &
Start ldsp_user...0
Ldsp cfg start at 13, Line: 769  
<LDSP>Set uiUpMode=2.
Board id is 1 !
Pcb id is 2 !
SD5113 test self OK
Lsw test self OK
EPON opened success !
Ldsp cfg  end at 13, Line: 813  
<LDSP>Set uiUpMode=2.
<LDSP>[hw_ldsp_user.c_417]uiRet=0x0,par1=0x0,par2=0x0,par3=0x0,par4=0x0,
hw_ldsp_user HW_LdspUser_NetLink_Init ok !
<LDSP>[hw_ldsp_user.c_135]uiRet=0x0,par1=0x4,par2=0x4,par3=0x0,par4=0x0,
hw_quickcfg_resume.c <75>     uiRet=0x00000000 arg=0x00000000
system not enable the restore flag!
HW_DIA_InitHmem success;
HW_Shell_InitFuncReg.uiReturn=0x00000000;
Process 497 start into next state 0; MID=0;
Process 497 end set state;
HW_DIA_InitHmem success;
HW_Shell_InitFuncReg.uiReturn=0x00000000;
Process 498 start into next state 0; MID=0;
Process 498 end set state;
HW_DIA_InitHmem success;
HW_Shell_InitFuncReg.uiReturn=0x00000000;
[HMEM]Start Times uiStartNum = 0x0.
[HMEM]HMEM initial success.
HW_DIA_InitHmem success;
HW_Shell_InitFuncReg.uiReturn=0x00000000;
Process 505 start into next state 0; MID=0;
Process 505 end set state;
HW_DIA_InitHmem success;
HW_Shell_InitFuncReg.uiReturn=0x00000000;
Process 508 start into next state 0; MID=0;
Process 508 end set state;
  PID  Uid     VmSize Stat Command
WAP Loaded Custom Configuration <Msg>: 0x00000000;
ProcMax=30          ModuleMax=20      
GroupMax=2          TraceMax=8      
StatMax=16          MqLenMax=4096   
uiMqNumMax=1024            
Read line cwmp cwmp 1
HW_DIA_InitHmem success;
HW_Shell_InitFuncReg.uiReturn=0x00000000;
Process 496 start into next state 0; MID=0;
Process 496 end set state;
    1 root        608 S   init      
    2 root            SWN [ksoftirqd/0]
    3 root            SW  [watchdog/0]
    4 root            SW< [events/0]
    5 root            SW< [khelper]
    6 root            SW< [kthread]
   30 root            SW< [kblockd/0]
   33 root            SW< [khubd]
   47 root            SW  [pdflush]
   48 root            SW  [pdflush]
   49 root            SW< [kswapd0]
   50 root            SW< [aio/0]
   65 root            SW  [mtdblockd]
  113 root        256 S   init      
  114 root        572 S   /bin/sh /etc/rc.d/rc.sysinit
  192 root        600 S   /bin/sh /etc/rc.d/rc.start/1.sdk_init.sh start
  207 root            SWN [jffs2_gcd_mtd7]
  429 root            SW  [mpcp]
  435 root            SW< [kTimerTask]
  456 root            SW  [cpucar]
  476 root        544 S   start ssmp bbsp vspa igmp amp tran_console cwmp apm
  492 root        824 S   hw_ldsp_user
  495 root       1344 R   ssmp
  496 root       1220 R   bbsp
;
Load auto start conig:0 cwmp cwmp 1
Read line ethoam ethoam 1
;
Load auto start conig:1 ethoam ethoam 1
WAP Loaded Custom Configuration <Db>: 0x00000000;
uiEnable=1            MsgWaitTime=10000   
  497 root        936 S   amp
  498 root        892 S   igmp
  503 root        560 S   /bin/sh /bin/watchproc.sh vspa_sip
  505 root        948 S   cwmp
  506 root        828 S   smp_usb
  508 root        828 S   apm
  509 root        240 S   /bin/sh /etc/rc.d/rc.start/1.sdk_init.sh start
  510 root        380 S   sleep 30
  511 root        240 S   /bin/sh /etc/rc.d/rc.start/1.sdk_init.sh start
  512 root       1248 R N vspa_sip
  513 root        380 S   sleep 60
  514 root        380 S   sleep 30
  515 root        240 S   /bin/sh /etc/rc.d/rc.start/1.sdk_init.sh start
  516 root        380 S   sleep 40
  517 root        604 R   ps
HW_DIA_InitHmem success;
HW_Shell_InitFuncReg.uiReturn=0x00000000;
Process 531 start into next state 0; MID=0;
Process 531 end set state;
VSPA pri from 0 to 10
HW_DIA_InitHmem success;
HW_Shell_InitFuncReg.uiReturn=0x00000000;
Process 512 start into next state 0; MID=0;

BusyBox v1.4.1 (2011-05-06 16:50:30 HKT) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
Process 512 end set state;
WAP(Dopra Linux) # WAP Loaded Custom Configuration <Dev>: 0x00000000;
MaxProduct=3      
[DEV]HW_DM_InitLocalData failed.uiRet = 0xf7205405
[DEV]HW_DM_BoardInit failed.uiRet = 0xf7205405
Init Dev Error! Return=0xf7205405;
HW_Init_ModuleSsp, Line: 682  result : -148876283
Get signal:0 backtrace ...
/lib/libhw_ssp_os.so(HW_OS_SignalTrapUser1+0x58) [0x40062de0]
/lib/libhw_ssp_os.so(HW_Init_Frame+0x14c) [0x4006c1b4]
ssmp(main+0x54) [0x1cdc4]
/lib/libc.so.6(__libc_start_main+0x180) [0x402b18cc]
HW_Init_Frame error. uiReturn=-148876283;
Dropped the page cache.
HW_DIA_InitHmem success;
HW_Shell_InitFuncReg.uiReturn=0x00000000;
call HW_MSG_Init err:0xf7101012
call HW_MSG_RegisterMID 1 err:0xf7101005
call HW_MSG_RegisterMID 2 err:0xf7101005
<7>ethoam: unhandled page fault (11) at 0x00000028, code 0x017
pgd = c22e4000
[00000028] *pgd=923fd031, *pte=00000000, *ppte=00000000
Pid: 548, comm:               ethoam
CPU: 0
PC is at 0x400deb6c
LR is at 0x400e46e0
pc : [<400deb6c>]    lr : [<400e46e0>]    Tainted: P      
sp : 40c1bdb8  ip : 40c1bde8  fp : 40c1bde4
r10: 400f154c  r9 : 400297c8  r8 : 00800000
r7 : 00000152  r6 : 40c1c490  r5 : 00000001  r4 : 40c1c4d8
r3 : 00000000  r2 : 00000000  r1 : 00000000  r0 : 00000000
Flags: nZCv  IRQs on  FIQs on  Mode USER_32  Segment user
Control: C5387D
Table: 922E4008  DAC: 00000015
[<c002520c>] (show_regs+0x0/0x50) from [<c002bed4>] (__do_user_fault+0x5c/0xa4)
r4 = C18C8D60
[<c002be78>] (__do_user_fault+0x0/0xa4) from [<c002c094>] (do_page_fault+0xfc/0x240)
r7 = C18C8D60  r6 = C25E5574  r5 = C2273288  r4 = C25E5540
[<c002bf98>] (do_page_fault+0x0/0x240) from [<c002c344>] (do_DataAbort+0x3c/0xa0)
[<c002c308>] (do_DataAbort+0x0/0xa0) from [<c0023be0>] (ret_from_exception+0x0/0x10)
r8 = 00800000  r7 = 00000152  r6 = 40C1C490  r5 = 00000001
r4 = FFFFFFFF
Signal Trap:11
Get signal:11 backtrace ...
/lib/libhw_ssp_os.so(HW_OS_SignalTrapUser1+0x58) [0x40062de0]
/lib/libhw_ssp_dia.so(HW_DIA_SigActionTrapFunc+0x130) [0x4007f7e8]
/lib/libc.so.6(__default_rt_sa_restorer_v2+0) [0x4021d600]
/lib/libhw_ssp_msg.so(HW_MSG_GetAndDispatch+0x8c) [0x400e46e0]
ethoam(HW_ETHOAM_TASK+0x18) [0x13540]
/lib/libpthread.so.0 [0x400299a8]
ETHOAM Init Lsw lib Tbl Error! Return=2;
ETHOAM Init error. uiReturn=2;
HW_MU_FreeRes::Destroy GmemList!
Init MU Message Error! Return=0xf7101012;
vspa_sip Started by WatchProc!
Init Watchdog Message Error! uiRet=0xf7101012;
Init TimeOut, Line: 189   
Init TimeOut, Line: 189   
Init TimeOut, Line: 189   
Init TimeOut, Line: 189   
Init TimeOut, Line: 189   
Init TimeOut, Line: 189   
Init TimeOut, Line: 189   
Init TimeOut, Line: 189   
Init TimeOut, Line: 189   
Init TimeOut, Line: 189   
Init TimeOut, Line: 189   

发表于 2014-1-9 12:43:29 | 显示全部楼层
与我的情况一样的。而且无法通过按d中断autoboot.等高人出现
发表于 2014-1-9 20:10:09 | 显示全部楼层
为了猫猫·····
 楼主| 发表于 2014-1-10 12:00:01 | 显示全部楼层
怎么高人还没现身,快来帮忙看看,还有没有救。谢了
发表于 2014-1-14 13:27:14 | 显示全部楼层
尝试使用TTL线重新刷固件,或者可以尝试恢复HW_boradinfo.xml。应该有一个HW_boradinfo.xml.bak的文件在同一级目录下面的。
 楼主| 发表于 2014-1-14 15:27:05 | 显示全部楼层
谢谢楼上的解答,TTL线连上后,开电,代码就不停的涌,无法中断。TTL怎么重新刷固件,楼上的高人可不可以说的明白一些,telnet上不去,HW_boradinfo.xml怎么恢复过来,这个文件我事前有备分的,期待楼上的高手再次明示,非常感谢指导!!
发表于 2014-1-17 11:36:09 | 显示全部楼层
启动时候按   Ctrl + C看看能否中断,然后就是一些基本的Linux命令了.
我自己没试过.
https://www.chinadsl.net/forum.ph ... amp;_dsign=11acb8ce
参考这个看看.
发表于 2014-6-29 14:36:44 | 显示全部楼层
lawman 发表于 2014-1-14 13:27
尝试使用TTL线重新刷固件,或者可以尝试恢复HW_boradinfo.xml。应该有一个HW_boradinfo.xml.bak的文件在同 ...

进入wap> 不能开启shell
怎么恢复那个bak文件啊? 求教大侠
*滑块验证:
您需要登录后才可以回帖 登录 | 注册

本版积分规则

Archiver|小黑屋|宽带技术网 |网站地图 粤公网安备44152102000001号

GMT+8, 2025-7-12 16:22 , Processed in 0.027713 second(s), 4 queries , Redis On.

Powered by Discuz! X3.5 Licensed

Copyright © 2001-2020, Tencent Cloud.

快速回复 返回顶部 返回列表