【BCM6358】DB120-B1(DSL-2650U_V2.05_CFE_128K)
（1）由“RU_DSL-2650U_2.05_07282010_cfe_fs_kernel”重新组合为128K固件所使用的命令为:brfwmod -comp -o newfile.bin /m:2 /128K /s1 /b0
（2）发布日期:2010年7月28日
（3）版本号V2.05，修改内容不详
（4）Device Info
Board ID: 96358VW2
Software Version: RU_2.05
Bootloader (CFE) Version: 1.0.37-10.1
Release Date: Jul. 28, 2010
Wireless Driver Version: 4.100.27.0.cpe2.1
（5）刷机后建议去CEF状态用e n命令清除nvram，所以最好有TTL线备用
（6）解压后MD5为:adf3596eac3a521379a984b06558df2f
（7）下载地址：
--------------------------------
世事漫随流水，算来一梦浮生
processor@163.comQQ16866027 我的DB120-B1 被朋友拿去用了！没有机会忙测试了！ 有设备的同学弄起！ 本帖最后由 zengcf 于 2010-8-7 10:01 编辑
【BCM6358】DB120-B1(DSL-2740B_V3.03b491_CFE_128K)
本帖最后由 zengcf 于 2010-8-7 10:01 编辑（1）DSL-2740B更新至v3.03B491(Firmware 2010.07.19发布)
（2）MD5:bf552452b5ab30b35f19dfbfc9f4f0e5
（3）下载地址:
https://www.chinadsl.net/attachments/month_1007/100721165045742324f29709fe.jpg
https://www.chinadsl.net/attachments/month_1007/1007211653dcb243146d270b77.jpg 好用么？？
2650刚更新2.05 本帖最后由 zengcf 于 2010-8-7 10:04 编辑
好用么？？
2650刚更新2.05
tq0c10o0 发表于 2010-8-7 09:37 https://www.chinadsl.net/images/common/back.gif
TD-W8960N v1的固件（w8960nv1_en_1_3_5_100510R50771.up）有问题，偶尔打开网页会跳转到路由器登陆界面，非DNS原因，并且静态路由和IPSEC VPN设置后需要重启才生效，所以制作了2650 V2.05的版本，在公司环境使用，目前未发现问题。
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2010.08.06 14:15:49 =~=~=~=~=~=~=~=~=~=~=~=
CFE version 1.0.37-10.1 for BCM96358 (32bit,SP,BE)
Build Date: Tue Apr 24 15:57:24 CST 2007 (gavin@FD5)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x80527C50 (1207376)
Initialized Data: 0x8041D580 - 0x8041F480 (7936)
BSS Area: 0x8041F480 - 0x80425C50 (26576)
Local Heap: 0x80425C50 - 0x80525C50 (1048576)
Stack Area: 0x80525C50 - 0x80527C50 (8192)
Text (code) segment: 0x80401000 - 0x8041D57C (116092)
Boot area (physical): 0x00528000 - 0x00568000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-8) : 96358VW2
Number of MAC Addresses (1-32) : 12
Base MAC Address : 00:e0:fc:00:e0:fc
PSI Size (1-64) KBytes : 24
Main Thread Number : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 110
Booting from only image (0xbe800000) ...
Code Address: 0x80010000, Entry Address: 0x80243018
Decompression OK!
Entry at 0x80243018
Closing network.
Starting program at 0x80243018
Linux version 2.6.8.1 (root@BB3) (gcc version 3.4.2) #1 Wed Jul 28 14:10:45 CST 2010
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 4000 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 29508k/32384k available (1926k kernel code, 2832k reserved, 321k data, 76k init, 0k highmem)
Calibrating delay loop... 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...unavailable.
NET: Registered protocol family 16
Total Flash size: 16384K with 128 sectors
File system address: 0xbe800100
Can't analyze prologue code at 801f0084
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NTFS driver 2.1.15 .
Initializing Cryptographic API
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v1.0
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0000300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0002400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
usbcore: registered new driver usbserial_generic
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x3 is enabled
======= GPIO CONFIG_BCM96358 init ========
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 76k freed
init started:BusyBox v1.00 (2010.07.28-06:13+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
BusyBox v1.00 (2010.07.28-06:13+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
fuse init (API version 7.8)
fuse distribution version: 2.7.3
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Jul 28 2010 14:09:13
Config Ethernet Switch Through MDIO Pseudo PHY Interface
dgasp: kerSysRegisterDyingGaspHandler: eth0 registered
eth0: MAC Address: 00:E0:FC:00:E0:FC
Broadcom BCM6358A1 USB Network Device v0.4 Jul 28 2010 14:09:15
usb0: MAC Address: 00 E0 FC 00 E0 FD
usb0: Host MAC Address: 00 E0 FC 00 E0 FE
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 00:E0:FC:00:E0:FF
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.100.27.0.cpe2.1
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
eth0 Link UP.
is not default cfg.
is not default cfg.
BcmAdsl_Initialize=0xC006B808, g_pFnNotifyCallback=0xC0084834
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
pSdramPHY=0xA1FFFFF8, 0xFFD3FFFF 0xFBFFFFFF
AdslCoreHwReset: AdslOemDataAddr = 0xA1FFD3D4
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
ATM proc init !!!
==> Bcm963xx Software Version: RU_2.05 <==
device usb0 entered promiscuous mode
br0: port 1(usb0) entering learning state
br0: topology change detected, propagating
br0: port 1(usb0) entering forwarding state
device eth0 entered promiscuous mode
br0: port 2(eth0) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0) entering forwarding state
Setting SSID "Dlink"
SIOCGIFFLAGS: No such device
Setting country code using abbreviation: "US"
wlctl: Not Found
wl0: current channel 11
device wl0 entered promiscuous mode
br0: port 3(wl0) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0) entering forwarding state
wlSesEnable=1 ,wlSesEvent=2, wlSesStates=01:01
ses: not found
echo wlSesClEnable=1 ,wlSesClEvent=0
ses_cl: not found
ioctl, p_name=diapd
I am open &async_queue = 0xc0055520wlButtonInit open success
<0> gpio_fasync
Pasync_queue->magic = 0x4601
*** diapwait system init 1 sec start
##############status LED blink now##################
no config file /etc/resolv.conf
*** diapwait system init 1 sec end
dft, wanIpAddress = , wanSubnetMask =
vpi = 0, vci = 0, conId = 0, portId = 0
nat = 0, firewall = 0
br0: port 1(usb0) entering disabled state
iStatus = 0, iDaemonStatus = 0
iStatus = 0, iDaemonStatus = 0 谢谢楼主，更新中。。。。。。。(jianxiao: 回复 1# zengcf
顶上啊，好东西，下载 回复 4# zengcf
又来一个，继续顶 下来试试，谢谢