华勤天地HGG420N v3 TTL启动信息，无法使用shell， 请教高人
以下贴如启动信息 （拆机使用TTL读取） 请教高人如何使用命令？BootROM 1.34
Booting from NAND flash
BootROM: Image checksum verification PASSED
Gpon System Boot
Copyright 2011 CIG Gpon ONT System.
CPU : GPON Soc
BOOT version: V8.1.18
PEX 1: Root Complex Interface, Detected Link X1
DRAM : 128 MB
NAND:1bit HM ECC, Size: 64 MiB
EEPROM version: 0x0003
USB 0: Host Mode
Modules Detected:
GPON module detected.
Ethernet Switch on MAC0.
3xFE PHY Module.
GE-PHY on Switch port #0.
Net: egiga0 , egiga1
**************************************
* *
*KEY -- Enter console terminal *
* *
**************************************
waiting for your select ...
Loading 'uImage' fromCRAMFS Partition 'imageb' to 0x2000000.
Root Filesystem crc check successfully!
### CRAMFS load complete: 2058620 bytes loaded to 0x2000000
Software version:1.22UYY.1H1
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linux-2.6.32.11
Created: 2013-06-0613:37:12 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2058556 Bytes =2 MB
Load Address: 00008000
Entry Point:00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux...................................................................................................................................... done, booting the kernel.
Linux version 2.6.32.11 (root@sw-server) (gcc version 4.2.4) #1 Thu Jun 6 21:37:06 CST 2013
CPU: Feroceon 88FR131 revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Feroceon-KW2
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.Total pages: 32512
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock3 mtdparts=nand_mtd:0x100000@0x0(Boot1),0x200000@0x200000(Config1),18M@0x600000(ImageA),18M@0x2100000(ImageB),4M@0x3c00000(MidWare),0x100000@0x100000(Boot2),0x200000@0x400000(Config2),9M@0x1800000(Imagec1),9M@0x3300000(Imagec2) rootfstype=cramfs mv_net_config=0 mv_phone_config=dev0:fxs,dev1:fxs mem=128M flash=nand 5srst=0 pwrLed=255 ethOpt=560
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 125296KB available (3840K code, 525K data, 104K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:192
Console: colour dummy device 80x30
Calibrating delay loop... 1191.93 BogoMIPS (lpj=595968)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Feroceon L2: Cache support initialised.
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB
SDRAM_CS1 ....no such
SDRAM_CS2 ....no such
SDRAM_CS3 ....no such
DEVICE_CS0 ....no such
DEVICE_CS1 ....no such
DEVICE_CS2 ....no such
DEVICE_CS3 ....no such
PEX0_MEM ....base f3000000, size16MB
PEX0_IO ....base f2000000, size 1MB
PEX1_MEM ....base f4000000, size16MB
PEX1_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
NAND_NOR_CS ....base f8000000, size 2MB
SPI_CS0 ....base f0000000, size16MB
SPI_CS1 ....no such
SPI_CS2 ....no such
SPI_CS3 ....no such
SPI_CS4 ....no such
SPI_CS5 ....no such
SPI_CS6 ....no such
SPI_CS7 ....no such
SPI_B_CS0 ....no such
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT1_ENG ....base f2200000, size 2MB
CRYPT2_ENG ....no such
PNC_BM ....base f5000000, size 1MB
ETH_CTRL ....base f5100000, size 1MB
PON_CTRL ....base f5200000, size 1MB
NFC_CTRL ....no such
Marvell Development Board (LSP Version KW2_LSP_2.0.5_p14_NQ)-- RD-88F6560-GWSoc: MV88F6560 Rev 2 LE
Detected Tclk 200000000 and SysClk 0
Marvell USB EHCI Host controller #0: c783e800
PEX0 interface detected no Link.
PEX1 interface detected Link X1
PCI: bus0: Fast back to back transfers enabled
pci 0000:01:01.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:01:01.0: PME# disabled
PCI: bus1: Fast back to back transfers disabled
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource kw_clocksource
Switched to NOHz mode on CPU #0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
RTC has been updated!!!
rtc mv_rtc: rtc core: registered kw-rtc as rtc0
RTC registered
cpufreq: Init kirkwood cpufreq driver
NFP (fib) init 16384 entries, 65536 bytes
NFP (pnc) init 471 entries, 13188 bytes
cesadev_init(c000cad0)
mvCesaInit: channels=1, session=640, queue=64
JFFS2 version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc.
fuse init (API version 7.13)
msgmni has been set to 245
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console enabled
loop: module loaded
NAND device: Manufacturer ID: 0x98, Chip ID: 0x76 (Toshiba NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
9 cmdlinepart partitions found on MTD device nand_mtd
Using command line partition definition
Creating 9 MTD partitions on "nand_mtd":
0x000000000000-0x000000100000 : "Boot1"
0x000000200000-0x000000400000 : "Config1"
0x000000600000-0x000001800000 : "ImageA"
0x000002100000-0x000003300000 : "ImageB"
0x000003c00000-0x000004000000 : "MidWare"
0x000000100000-0x000000200000 : "Boot2"
0x000000400000-0x000000600000 : "Config2"
0x000001800000-0x000002100000 : "Imagec1"
0x000003300000-0x000003c00000 : "Imagec2"
0 - Base 0x00000000 , Size = 0x08000000.
8 - Base 0xf3000000 , Size = 0x01000000.
9 - Base 0xf2000000 , Size = 0x00100000.
10 - Base 0xf4000000 , Size = 0x01000000.
11 - Base 0xf2100000 , Size = 0x00100000.
12 - Base 0xf1000000 , Size = 0x00100000.
13 - Base 0xf8000000 , Size = 0x00200000.
14 - Base 0xf0000000 , Size = 0x01000000.
25 - Base 0xf2200000 , Size = 0x00200000.
27 - Base 0xf5000000 , Size = 0x00100000.
28 - Base 0xf5100000 , Size = 0x00100000.
29 - Base 0xf5200000 , Size = 0x00100000.
mvPncVirtBase = 0xc8c00000
o 3 Giga ports supported
o Giga PON port is #2: - 8 TCONTs supported
o SKB recycle supported (Enabled)
o NETA acceleration mode 4
o BM supported: short buffer size is 256 bytes
o PnC supported
o HWF supported
o PMT supported
o RX Queue support: 8 Queues * 128 Descriptors
o TX Queue support: 8 Queues * 256 Descriptors
o GSO supported
o GRO supported
o Receive checksum offload supported
o Transmit checksum offload supported
o Network Fast Processing (Routing) supported
o Driver ERROR statistics enabled
o Driver INFO statistics enabled
o Driver DEBUG statistics enabled
o Proc tool API enabled
o Switch support enabled
o IGMP special processing support
o Loading Switch QuarterDeck driver
o Internal GE PHY Connected to Switch Port 0 Detected
o Setting Switch CPU port (port #4) for 1000 Full with FC
o Setting Switch CPU port (port #5) for 1000 Full with FC
o Disable disconnected switch port (port #6) and force link down
o Loading 3 network interface(s)
o Port 0 is connected to Linux netdevice
o Using UBoot netconfig string
net_config_str: 0
o Working in External Switch mode
giga p=0: mtu=2000, mac=c7819f6a
eth0: Dropping NETIF_F_SG since no checksum feature.
o eth0, ifindex = 2, GbE port = 0
o Port 1 is connected to Linux netdevice
o Using UBoot netconfig string
net_config_str: 0
o Working in External Switch mode
giga p=1: mtu=2000, mac=c7819f6a
eth1: Dropping NETIF_F_SG since no checksum feature.
o eth1, ifindex = 3, GbE port = 1
o Port 2 is connected to Linux netdevice
pon p=2: mtu=2000, mac=c7819f6a
eth2: Dropping NETIF_F_SG since no checksum feature.
o eth2, ifindex = 4, GbE port = 2
PPP generic driver version 2.4.2
PPP BSD Compression module registered
NET: Registered protocol family 24
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
Linux telephony interface: v1.00
Loading Marvell vpapi device
Loading Marvell tdm device
cpuidle: using governor ladder
cpuidle: using governor menu
nf_conntrack version 0.5.0 (1960 buckets, 7840 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
TCP cubic registered
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Marvell Kirkwood2 Power Management Initializing
rtc mv_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
VFS: Mounted root (cramfs filesystem) readonly on device 31:3.
Freeing init memory: 104K
Populating /dev using udev: done
Initializing random number generator... read-only file system detected...done
Starting system message bus: done
Starting network...
RTNETLINK answers: File exists
:Extract Board Configuration
:Load kernel modules
mv_eth_ports_num = 3
mv_eth_rx_special_proc_func register
mv_eth_rx_special_proc_func register
mv_eth_rx_special_proc_func register
mv_eth_tx_special_check_func register
mv_eth_tx_special_check_func register
mv_eth_tx_special_check_func register
= SW Module SYS FS Init ended successfully =
= TPM Module Init ended successfully =
: Start XPON
pon interface is eth2
: Start Data Configuration
: Start Network
pool #0: pkt_size=2048, buf_size=2144 - 2048 of 2048 buffers added
pool #3: pkt_size=256, buf_size=352 - 2048 of 2048 buffers added
eth0: link up
eth0: started
pool #1: pkt_size=2048, buf_size=2144 - 2048 of 2048 buffers added
pool #3: pkt_size=256, buf_size=352 - 2048 of 2048 buffers added
eth1: link up
eth1: started
pool #2: pkt_size=2048, buf_size=2144 - 2048 of 2048 buffers added
pool #3: pkt_size=256, buf_size=352 - 2048 of 2048 buffers added
pon0: link up
pon0: started
Empty flash at 0x0016e33c ends at 0x0016e400
# num is 10,nothing need to do
ONT>
Update timer: curTime=6acfb7f3, gTmrTimerMsCounter=00000000
Starting Application: 0x00002000, /bin/TimerMgr................Done. elapsed time:(1005)ms
Starting Application: 0x00001000, /bin/LogMgr................Done. elapsed time:(1004)ms
Starting Application: 0x00007000, /bin/MiscMgr................Done. elapsed time:(1004)ms
Check base image file CRC ... cal_crc (87f378cb) ori_crc (87f378cb) Success.
Mount Backup as cramfs...Success.
major ID minor ID
VOS_XML_Init():
Load XML OK from file /mnt/rwdir/runtime_rg.xmlVOS_XML_Init():
Load XML OK from file /tmp/default_rg.xmlVOS_XML_Init():
Load XML OK from file /tmp/runtime_rg.xmlVOS_XML_Init():
Load XML OK from file /tmp/runtime_rg.xmlVOS_XML_Init():
Load XML OK from file Starting Application: 0x00003000, /bin/MecMgr................Done. elapsed time:(1083)ms
Starting Application: 0x00004000, /bin/PonMgr................Done. elapsed time:(1005)ms
Starting Application: 0x00009000, /bin/NetMgr................Done. elapsed time:(1008)ms
Starting Application: 0x00006000, /bin/VmrMgr................Done. elapsed time:(1009)ms
Starting Application: 0x00005000, /bin/EthMgr................Done. elapsed time:(1009)ms
CfgDIR = /etc/tr069cfg
cd /tmp/cpe3
dir = data
dir = filetrans
dir = options
dir = parameter
cdir = /tmp/cpe3
add call back OK
add call back OK
Starting Application: 0x0000d000, /bin/tr069Mgr................Done. elapsed time:(3151)ms
ln: /tmp/web/web: Read-only file system
Starting Application: 0x0000c000, /bin/WebMgr................Done. elapsed time:(1019)ms
3cae0270:Exit SSP -->ssp, msg 0x50000,elapsed time:21570 ms
cb78f387 cb78f387 cb78f387
3cc70c2e:Exit MEC -->pmr, msg 0xc0002,elapsed time:716 ms
Sync 0xc0002, msg no reply, dest NET, VOS_SendSyncMsg:2031
/tmp/default_rg.xmlVOS_SendSyncMsg:2040 Recv sync response failed
slic profile checksum 0x7AC5 ok!
VOS_XML_Init():
Load XML OK from file 3cf35512:Exit MEC -->net, msg 0xc0002,elapsed time:2898 ms
set Sip LCFO = 03d0297eb:Exit TMR -->tr069Mgr, msg 0x10001(timeid:0xd),elapsed time:517 ms
3d242928:Exit MEC -->vmr, msg 0xc0002,elapsed time:4246 ms
Sync 0xc0002, msg no reply, dest TR069, VOS_SendSyncMsg:2031
/mnt/rwdir/voicecfg.xmlVOS_SendSyncMsg:2040 Recv sync response failed
Sync 0xc0004, msg no reply, dest EMR, VOS_SendSyncMsg:2031
VOS_SendSyncMsg:2040 Recv sync response failed
Sync 0x60003f, msg no reply, dest MEC, VOS_SendSyncMsg:2031
VOS_SendSyncMsg:2040 Recv sync response failed
3d761d98:Exit TMR -->tr069Mgr, msg 0x10001(timeid:0xd),elapsed time:1047 ms
3d7ebae3:Exit MEC -->emr, msg 0xc0004,elapsed time:4403 ms
3d7ed714:Exit MEC -->pmr, msg 0x8001c,elapsed time:2871 ms
INFO: ALL APPs are ready.
3d7ef2d4:Exit TR069 -->mec, msg 0xc0000,elapsed time:12770 ms
APPL 3000, Warning: do not reply sync message 0x600070
set http_redirect from 0 to 0
3dbf31e8:Exit TMR -->mec, msg 0x10001(timeid:0x11),elapsed time:686 ms
ifconfig: SIOCSIFFLAGS: Cannot assign requested address
set firstdial record from 0 to 0
Configuration file: /tmp/hostapd.conf
ioctl: Network is down
Using interface wlan0 with hwaddr 60:bb:0c:3f:d1:2a and ssid 'ChinaNet-Workstation'
3df39143:Exit TMR -->tr069Mgr, msg 0x10001(timeid:0xd),elapsed time:630 ms
423ff516:Exit MEC -->mmr, msg 0xc000c,elapsed time:1008 ms
42426777:Exit PMR -->mec, msg 0x60000,elapsed time:831 ms
42815af3:Exit TMR -->mec, msg 0x10001(timeid:0x1b),elapsed time:656 ms
>>>>>> recv sync timer at Sat Jan1 00:02:03 2000
<<<<<<
429065e7:Exit TMR -->net, msg 0x10001(timeid:0x12),elapsed time:533 ms
Using interface ppp1
Connect: ppp1 <--> /dev/pts/0
429bd162:Exit TMR -->net, msg 0x10001(timeid:0x13),elapsed time:748 ms
Warning - secret file /etc/ppp/pap-secrets has world and/or group access
have_chap_secret: g_am_server 0, /etc/ppp/chap-secrets
Warning - secret file /etc/ppp/pap-secrets has world and/or group access
upap_authwithpeer PPPOE_ACCOUNT_NAME 02367648351
Remote message: Authentication success,Welcome!
PAP authentication succeeded
session id 0x0646
my eth 60:bb:0c:3f:d1:2d:
peer eth e0:24:7f:94:11:a5:
localIP address 14.105.99.116
remote IP address 14.105.64.1
primary DNS address 61.128.128.68
secondary DNS address 61.128.192.68
udhcpc (v1.18.4) started:dhcp_type is 0
Sending discover...
Sending select for 10.6.43.166...
42a40016:Exit TMR -->net, msg 0x10001(timeid:0x15),elapsed time:530 ms
Jan1 00:02:05 upnpd: Initializing UPnP SDK ...
42ac1ab9:Exit UNKNOWN -->net, msg 0xd0026,elapsed time:514 ms
Lease of 10.6.43.166 obtained, lease time 259200
Lookup: devacs.edatahome.com from 10.6.43.166 by priDns: 192.168.8.2 secDns: 192.168.8.3 in ansy mode
Lookup return ipAddr: 0.0.0.0
Lookup send msg ipAddr: 1e00a8c0 to id: 53248
----------------Media gateway 0 config-------------------
Media gatewy idx : 0
State : Used
OMCI ME id : 0
MEGACO version : 1
Encoding Method: text long
Transport Type : UDP
Max Retry Time : 20
max retry attemps: 20
SC delay : 0
primary mgc : 172.31.252.130:2944
secondary mgc : :0
num of term : 2
Term List : 0 1
Local Address : 172.39.210.214:2944
TOS : 0
Phy Termid base : AG58900
RTP Termid base : RTP/
First Term idx : 0
First Rtp idx : 0
Heartbeat : 16500
Message Id : LG2070565194 (DOMAIN)
Interface index : 3
42e33c5c:Exit TR069 -->tr069Mgr, msg 0x200001,elapsed time:1000 ms
Save Event: 4 VALUE CHANGECommandKey:
Save Event: 1 BOOTCommandKey:
Freeing: 0 4 VALUE CHANGE
Freeing: 0 1 BOOT
ONT>ls
ONT>pwd
good.......................................................
页:
[1]