这个只能在网页里边看， 网上邻居里边看不到， 2760u的可以
我连网页里面都看不到....根本不显示usb-modem和u盘
松鼠派 发表于 2013-3-31 17:16 static/image/common/back.gif
我连网页里面都看不到....根本不显示usb-modem和u盘
你刷的那个2750u ？
zhjook 发表于 2013-3-31 17:31 static/image/common/back.gif
你刷的那个2750u ？
在高级设置。 storege 里边
没有啊..刷个就是【DLINK】dsl-2750U_NRU_C(_BA_C1A)v1.0.11『 各类ADSL设备升级固件下载区 』 DSL_2750_v1.0.11_cfe_fs_kernel ,web管理那里的usb modem和Information about USB storage那里没任何新加入的modem或u盘的信息,只有ttl显示插入的时候是有一些反应,但最终还是没任何东西...
松鼠派 发表于 2013-3-31 18:51 static/image/common/back.gif
没有啊..刷个就是【DLINK】dsl-2750U_NRU_C(_BA_C1A)v1.0.11『 各类ADSL设备升级固件下载区 』 DSL_2750_v1 ...
看信息,加qq 吧
本帖最后由 松鼠派 于 2013-4-1 01:48 编辑
刷了 2760u不带cfe的固件后无限自动重启.刷回2640 2750的没事
另 usb接口果然如我所料 电源不足...接个100ma不到的u盘电压掉到3.5v,我加个带电源的hub就认出u盘了
CFE version 1.0.37-106.24 for BCM96328 (32bit,SP,BE)
Build Date: 袩褌薪 袗锌褉1 11:57:08 UTC 2011 (builder@cel366)
Copyright (C) 2000-2009 Broadcom Corporation.
HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
Total Flash size: 16384K with 4096 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-5) : 96328avng
Number of MAC Addresses (1-32) : 10
Base MAC Address : 00:10:18:00:00:00
PSI Size (1-64) KBytes : 24
Enable Backup PSI : 0
System Log Size (0-256) KBytes : 0
Main Thread Number : 0
Voice Board Configuration (0-11): AVNG_SI32267
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from latest image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x80014230
Decompression OK!
Entry at 0x80014230
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80014230
Linux version 2.6.30 (arriy@localhost.localdomain) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Mon Dec 6 10:59:20 CST 2010
HS Serial flash device: name , id 0xc218 size 0KB
96328avng prom init
CPU revision is: 0002a075 (Broadcom4350)
Determined physical RAM map:
memory: 03f00000 @ 00000000 (usable)
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00003f00
Movable zone start PFN for each node
early_node_map active PFN ranges
0: 0x00000000 -> 0x00003f00
On node 0 totalpages: 16128
free_area_init_node: node 0, pgdat 8034df10, node_mem_map 81000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 94 pages used for memmap
Normal zone: 11938 pages, LIFO batch:1
Built 1 zonelists in Zone order, mobility grouping on.Total pages: 16002
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
wait instruction: enabled
Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:128
PID hash table entries: 256 (order: 8, 1024 bytes)
console enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60252k/64512k available (2663k kernel code, 4240k reserved, 662k data, 120k init, 0k highmem)
Calibrating delay loop... 319.48 BogoMIPS (lpj=159744)
Mount-cache hash table entries: 512
net_namespace: 812 bytes
NET: Registered protocol family 16
Total Flash size: 0K with 0 sectors
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:09.0: reg 10 32bit mmio:
pci 0000:00:0a.0: reg 10 32bit mmio:
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:02:00.0: reg 10 64bit mmio:
pci 0000:02:00.0: supports D1 D2
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0: IO window: disabled
pci 0000:01:00.0: MEM window: 0x10f00000-0x10ffffff
pci 0000:01:00.0: PREFETCH window: disabled
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
BLOG v2.1 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
squashfs: version 4.0 with LZMA457 ported by BRCM
NTFS driver 2.1.29 .
fuse init (API version 7.11)
msgmni has been set to 117
io scheduler noop registered (default)
pcieport-driver 0000:01:00.0: device has invalid IRQ; check vendor BIOS
PCI: Setting latency timer of device 0000:01:00.0 to 64
Driver 'sd' needs updating - please use bus_type methods
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
bcm963xx_mtd driver v1.0
Address is too big.
Address is too big.
Failed to read image tag from flash
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
ehci_hcd 0000:00:0a.0: irq 50, io mem 0x10002500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 49, io mem 0x10002600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
ERROR - Invalid number of MAC addresses (1919251311) is configured.
SES: Button Interrupt 0x1 is enabled
SES: LED GPIO 0x8009 is enabled
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 36) is a BCM63XX
bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Dec6 2010 10:57:12
Broadcom Logger v0.1 Dec6 2010 10:56:47
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Cannot open root device "31:0" or unknown-block(31,0)
Please append a correct "root=" boot option; here are the available partitions:
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,0)
Rebooting in 1 seconds..
CFE version 1.0.37-106.24 for BCM96328 (32bit,SP,BE)
Build Date: ?????? ?????? 21 08:38:40 UTC 2012 (legath@desk)
Copyright (C) 2000-2009 Broadcom Corporation.
HS Serial flash device: name S25FL128, id 0x0118 size 16384KB
Total Flash size: 16384K with 256 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name: vmlinux
Default host flash file name: bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-6) : 96328avng
Number of MAC Addresses (1-32): 12
Base MAC Address : 00:10:18:00:00:00
PSI Size (1-64) KBytes : 24
Enable Backup PSI : 0
System Log Size (0-256) KBytes: 0
Main Thread Number : 0
Voice Board Configuration (0-11): AVNG_SI32267
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 110
Booting from latest image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x80014230
Decompression OK!
Entry at 0x80014230
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80014230
Linux version 2.6.30 (builder@rd) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Tue Apr 17 16:16:23 MSK 2012
HS Serial flash device: name S25FL128, id 0x0118 size 16384KB
96328avng prom init
CPU revision is: 0002a075 (Broadcom4350)
Determined physical RAM map:
memory: 03f00000 @ 00000000 (usable)
Zone PFN ranges:
DMA 砀 -> 0x00001000
一漀爀洀愀氀 砀 1000 -> 0x00003f00
Movable zone start PFN for each node
early_node_map active PFN ranges
0: 0x00000000 -> 0x00003f00
On node 0 totalpages: 16128
free_area_init_node: node 0, pgdat 80338810, node_mem_map 81000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
一漀爀洀愀氀 zone: 94 pages used for memmap
一漀爀洀愀氀 zone: 11938 pages, LIFO batch:1
Built 1 zonelists in Zone order, mobility grouping on.吀漀琀愀氀 pages: 16002
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
wait instruction: enabled
Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:128
PID hash table entries: 256 (order: 8, 1024 bytes)
console enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60276k/64512k available (2546k kernel code, 4216k reserved, 695k data, 120k init, 0k highmem)
Calibrating delay loop... 319.48 BogoMIPS (lpj=159744)
Mount-cache hash table entries: 512
net_namespace: 820 bytes
NET: Registered protocol family 16
Total Flash size: 16384K with 256 sectors
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:09.0: reg 10 32bit mmio:
pci 0000:00:0a.0: reg 10 32bit mmio:
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:02:00.0: reg 10 64bit mmio:
pci 0000:02:00.0: supports D1 D2
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0: IO window: disabled
pci 0000:01:00.0: MEM window: 0x10f00000-0x10ffffff
pci 0000:01:00.0: 倀刀EFETCH window: disabled
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
BLOG v3.0 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
squashfs: version 4.0 with LZMA457 ported by BRCM
fuse init (API version 7.11)
msgmni has been set to 117
io scheduler noop registered (default)
pcieport-driver 0000:01:00.0: device has invalid IRQ; check vendor BIOS
PCI: Setting latency timer of device 0000:01:00.0 to 64
Driver 'sd' needs updating - please use bus_type methods
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
bcm963xx_mtd driver v1.0
File system address: 0xb8010100
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd: block sizes: qh 128 qtd 96 itd 160 sitd 96
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: reset hcs_params 0x1111 dbg=0 cc=1 pcc=1 ordered ports=1
ehci_hcd 0000:00:0a.0: reset hcc_params 0016 thresh 1 uframes 256/512/1024 park
ehci_hcd 0000:00:0a.0: park 0
ehci_hcd 0000:00:0a.0: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
ehci_hcd 0000:00:0a.0: ...powerup ports...
ehci_hcd 0000:00:0a.0: MWI active
ehci_hcd 0000:00:0a.0: irq 50, io mem 0x10002500
ehci_hcd 0000:00:0a.0: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:0a.0: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
usb usb1: default language 0x0409
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.30 ehci_hcd
usb usb1: SerialNumber: 0000:00:0a.0
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: individual port power switching
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all ports
drivers/usb/core/inode.c: creating file '001'
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
drivers/usb/core/inode.c: creating file '002'
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: created debug files
ohci_hcd 0000:00:09.0: irq 49, io mem 0x10002600
ohci_hcd 0000:00:09.0: OHCI controller state
ohci_hcd 0000:00:09.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:09.0: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:09.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:09.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:09.0: intrenable 0x8000001a MIE UE RD WDH
ohci_hcd 0000:00:09.0: hcca frame #0022
ohci_hcd 0000:00:09.0: roothub.a 02000201 POTPGT=2 NPS NDP=1(1)
ohci_hcd 0000:00:09.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:09.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:09.0: roothub.portstatus 0x00000100 PPS
usb usb2: default language 0x0409
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.30 ohci_hcd
usb usb2: SerialNumber: 0000:00:09.0
usb usb2: uevent
hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: power on to power good time: 4ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: trying to enable port power on non-switchable hub
drivers/usb/core/inode.c: creating file '001'
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x1 is enabled
SES: LED GPIO 0x8009 is enabled
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
hub 2-0:1.0: state 7 ports 1 chg 0000 evt 0000
ttyS1 at MMIO 0xb0000120 (irq = 47) is a BCM63XX
bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Apr 17 2012 16:16:10
Broadcom Logger v0.1 Apr 17 2012 16:16:00
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
Freeing unused kernel memory: 120k freed
init started:BusyBox v1.00 (2012.04.17-12:16+0000) multi-call binary
making /var/log..
making /var/run..
making /var/state/dhcp..
making /var/ppp..
making /var/ppp/peers..
making /var/udhcpd..
making /var/zebra..
making /var/siproxd..
making /var/tmp..
mount: Mounting usbfs on /proc/bus/usb failed: Device or resource busy
gpio: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
start /etc/init.d/S*...
/etc/init.d/S*: not found
96328avng
BusyBox v1.00 (2012.04.17-12:16+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
Initialized fcache state
Broadcom Packet Flow CacheChar Driver v2.2 Sep 24 2010 18:42:19 Registered<242>
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Broadcom Packet Flow Cache learning via BLOG enabled.
Constructed Broadcom Packet Flow Cache v2.2 Sep 24 2010 18:42:19
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCM6328B0 Ethernet Network Device v0.1 Apr 17 2012 16:16:03
ETH Init: 180 tx BDs at 0xa3953000
ETH Init: 400 rx BDs at 0xa39f1000
ETH Init: 400 rx BDs at 0xa39f0000
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
eth0: MAC Address: 00:10:18:00:00:00
eth1: MAC Address: 00:10:18:00:00:00
eth2: MAC Address: 00:10:18:00:00:00
eth3: MAC Address: 00:10:18:00:00:00
eth4: MAC Address: 00:10:18:00:00:00
eth0 Link UP 100 mbps full duplex
message received before monitor task is initialized kerSysSendtoMonitorTask
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:02:00.0 to 64
otp_read_pci: bad crc
wl:not strapped or invalid data
wl:srom not detected,using main memory mapped srom info(wombo board)
wl:loading /etc/wlan/bcm4313_map.bin
wl0: Broadcom BCM4313 802.11 Wireless Controller 5.60.120.11.cpe4.06L03.8
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
p8021ag: p8021ag_init entry
Broadcom 802.1Q VLAN Interface, v0.1
===== Release Version 4.06L.03 (build timestamp 120417_1616) =====
flash 不同, 你的是mx25 ,我的是s25
我这个64 和128 的都没问题,给你的是64k的
先刷回dsl-2640NRU 1.0.20的用着.当ap用....