wkp_5 发表于 2014-3-15 10:47
怎么救活的，给个详细操作过程。
HELO
CPUI
L1CI
DRAM
CFE version 1.0.37-104.4 for BCM96328 (32bit,SP,BE)
Build Date: 2011??? 12??? 16??? ????????? 17:51:47 CST (root@localhost)
Copyright (C) 2000-2009 Broadcom Corporation.
HS Serial flash device: name MX25L12845E, id 0xc218 size 16384KB
Total Flash size: 16384K with 256 sectors
Flash not used for Auxillary File System
Blk# BlkOff Blks MemLenPartition Name
0000 001408 0001 0001024 NVRAM
0254 000000 0001 0049152 Backup PSI
0253 000000 0001 0049152 Syslog
0253 049152 0001 0008192 Scratch PAD
0255 016384 0001 0049152 PSI
0000 000000 0000 0000000 JFFS_AUXFS
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-3) : 96328Tavng
Number of MAC Addresses (1-32) : 11
Base MAC Address : 70:b9:21:40:ba:78
PSI Size (1-64) KBytes : 48
Enable Backup PSI : 1
System Log Size (0-256) KBytes : 48
Flash Block Size (1-256) in KBytes: 64
Auxillary File System Size Percent: 0
Main Thread Number : 0
Enable Small IMAGE : 0
ProductClass : HG110
WlSsid : CU_KdH5
WlKey : spwfzofe
UserPass : spwfzofe
DeviceId : 01110000000101152570B92140BA7800000000000000000000000
StartFlag : 1
send udp message finished.
Not response, auto boot ...
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 111
PANIC: out of memory!
failed to allocate memory with size: 8388608
PANIC: out of memory!
failed to allocate memory with size: 8323072
CFE> web info: Waiting for connection on socket 0.[J
CFE>
Pleas longin:
user:telecomadmin
passwd:********
*
login success
CFE> b
Press:<enter> to use current value
'-' to go previous parameter
'.' to clear the current value
'x' to exit this command
96328avng ------- 0
96328Tavng ------- 1
96328avng2lan ------- 2
96328Tavng2lan ------- 3
Board Id (0-3) :1
Number of MAC Addresses (1-32) :11
Base MAC Address :70:b9:21:40:ba:78
PSI Size (1-64) KBytes :48
Enable Backup PSI :1
System Log Size (0-256) KBytes :48
Flash Block Size (1-256) in KBytes:64
Auxillary File System Size Percent:0
Main Thread Number :0
Enable Small IMAGE :0
*** command status = 0
CFE> r
Booting from only image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x80306000
Decompression OK!
Entry at 0x80306000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
22 buffers found.
ttl 更改cpu id 的方法
高手啊。学习中。。。。
好贴子，尤其是如何恢复的部分。