yuanshichang 发表于 2012-10-27 22:29:49

求大神~~~~RG100AA 联通版 刷机挂彩 修复遇到困难！


Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot Kern
            AuxFS Misc PSI
Flash RootFS Partition Length: 12058624
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x80529860 (1214560)
Initialized Data:          0x8041E740 - 0x80421060 (10528)
Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.100
Gateway IP address                :   
Run from flash/host (f/h)         : f
Default host run file name      : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Board Id (0-8)                  : 96358VW2
Number of MAC Addresses (1-32)    : 11
Base MAC Address                  : 00:1f:a3:49:c0:93
PSI Size (1-64) KBytes            : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number           : 0
udp_send finished
No answer .auto boot ...
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Code Address: 0xFFFFFFFF, Entry Address: 0xffffffff
Failed on decompression.Corrupted image?
web error: HTTP POST start bound field not found.
web error: HTTP POST start bound field not found.
web error: HTTP POST start bound field not found.
web error: HTTP POST start bound field not found.
web error: HTTP POST start bound field not found.
web error: HTTP POST start bound field not found.
web error: HTTP POST start bound field not found.
web error: HTTP POST start bound field not found.
web error: HTTP POST start bound field not found.
web error: HTTP POST start bound field not found.
web error: HTTP POST start bound field not found.
web error: HTTP POST start bound field not found.
web error: HTTP POST start bound field not found.
web error: HTTP POST start bound field not found.
web info: Upload 8126468 bytes, Broadcom image format.
CFE>
Flashing root file system and kernel at 0xbe020000: ...............................................................
.
*** Image flash done *** !
Resetting board
求大神帮忙解决，试了好几天了，都这样，用JTAG 重刷CFE 后能看到TTL 信息，刷入固件后就这样了....谢谢了！实在没辙了！

YES东 发表于 2012-10-27 22:34:34

你是刷什么文件？

yuanshichang 发表于 2012-11-4 23:38:40

我用JTAG 第一步 输入 brjtag -probeonly /erasechip 全片擦除flash芯片数据
         第二部 刷cfe的命令    ：brjtag -flash:cfe
https://www.chinadsl.net/thread-46737-1-2.html 这是CFE
完成后 TTL 有反应了，然后
Boot Address 0xbe000000 Initializing Arena.Initializing Devices.Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB *** Board is not initialized properly *** Press:<enter> to use current value      '-' to go previous parameter      '.' to clear the current value      'x' to exit this command96358VW2         ------- 0 96358VW          ------- 1 96358GWVG      ------- 2 96358MV2G      ------- 3 96358M         ------- 4 96358B         ------- 5 96358BGWE_OEM1   ------- 6 96359PONG      ------- 7 96358SV          ------- 8 Board Id (0-8)                  :0Number of MAC Addresses (1-32)    :012Base MAC Address                  :00:00:00:00:00:00001fa36534adPSI Size (1-64) KBytes            :2464Flash Block Size (1-128) in KBytes:0128Auxillary File System Size Percent:024Main Thread Number           :00Flash layout changed. Need to erase all flash except bootromInvalid command: "e"Available commands: Flash Layout: Boot Kern            AuxFS Misc PSIFlash RootFS Partition Length: 12320768CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHzCPU running TP0Total memory: 33554432 bytes (32MB) Total memory used by CFE:0x80401000 - 0x80529860 (1214560)Initialized Data:          0x8041E740 - 0x80421060 (10528) ** Flash image not found. ** Board IP address                  : 192.168.1.1:ffffff00Host IP address                   : 192.168.1.100Gateway IP address                :   Run from flash/host (f/h)         : fDefault host run file name      : vmlinuxDefault host flash file name      : bcm963xx_fs_kernelBoot delay (0-9 seconds)          : 1Board Id (0-8)                  : 96358VW2Number of MAC Addresses (1-32)    : 12Base MAC Address                  : 00:1f:a3:65:34:adPSI Size (1-64) KBytes            : 64Flash Block Size (1-128) in KBytes: 128Auxillary File System Size Percent: 24Main Thread Number           : 0 udp_send finishedNo answer .auto boot ...CFE>
我下载论坛的联通的固件
https://www.chinadsl.net/thread-73516-1-1.html
进入192.168.1.1 输入密码telecomadmin/telecomadmin
开始刷机
web info: Upload 6864342 bytes, Broadcom image format.CFE> Flashing CFE: . Flashing root file system and kernel at 0xbe020000: ....................................................*** Image flash done *** ! Resetting board...就这样了.... 怎么都不行
我刷过论坛很多固件，都不行都上面这样

请教大神是不是我用过清 kernel命令 ，导致内核被清了？

飞

YES东 发表于 2012-11-5 11:26:07

你直接写入带cfe的固件试试。
页: [1]
查看完整版本: 求大神~~~~RG100AA 联通版 刷机挂彩 修复遇到困难！