上海贝曼ha910-n刷坏了，连接ttl 信息看不懂
ha910-n刷坏了，没有jtag接口，只好连接ttl试一下，得到的信息如下，不知道cfe有没有刷坏，如果没有坏下一步该怎么刷，现在192.168.1.1访问不了了，ping的时候有时会出出现数据丢失的情况， qq119864844LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN
CFE version 1.0.37-106.17-1 for BCM96328 (32bit,SP,BE)
Build Date: 2010-06-28 15:35:56 (wander@broadcom-eu)
Copyright (C) 2000-2009 Broadcom Corporation.
HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
*** Board is not initialized properly ***
Press:<enter> to use current value
'-' to go previous parameter
'.' to clear the current value
'x' to exit this command
96328A-1241N ------- 0
96328A-134 ------- 1
96328A-1341N ------- 2
96328A-1341N1 ------- 3
96328avng ------- 4
96328avngrP1 ------- 5
96328avngr ------- 6
963281TAN ------- 7
Board Id (0-7) :96328Tavng cfe参数需要重新设置，你看看按照这个的选择是否能正常：
Board Id (0-1) : 96328Tavng
Number of MAC Addresses (1-32) : 11
Base MAC Address : 02:10:18:01:00:01
PSI Size (1-64) KBytes : 48
Enable Backup PSI : 1
System Log Size (0-256) KBytes : 48
Flash Block Size (1-256) in KBytes: 64
Auxillary File System Size Percent: 0
Main Thread Number : 0
ProductClass : V1.0
WlSsid : SSID-1234
WlKey : 12345678
UserPass : 1234
DeviceId : 0123456789
StartFlag : 0 YES东 发表于 2012-8-15 15:34 static/image/common/back.gif
cfe参数需要重新设置，你看看按照这个的选择是否能正常：
Board Id (0-1) : 96328Tavn ...
第一次刷路由猫，弱弱地问一下cfe怎么设置的 可以qq吗 YES东 发表于 2012-8-15 15:34 static/image/common/back.gif
cfe参数需要重新设置，你看看按照这个的选择是否能正常：
Board Id (0-1) : 96328Tavn ...
该了一下可以ping通路由，可以打开192.168.1.1 但是没有登录密码 ttl信息如下
HELOaps
CPUIles
L1CIur k
DRAM nee
---- be
PHYSded.
ZQDN
PHYE
DINT
LSYN
USYN
e
MSYNcd
LMBEe wl
PASSt pr
----uous
ZBSSCI 1
CODE
DATA
L12F
MAIN: po
CFE version 1.0.37-106.17-1 for BCM96328 (32bit,SP,BE) choice
Build Date: 2010-06-28 15:35:56 (wander@broadcom-eu)
hub 1-0:1.0: 1 port detected
Copyright (C) 2000-2009 Broadcom Corporation. (OHCI) Driver
HS Serial flash device: name MX25L128, id 0xc218 size 16384KB -> 0002)
PCI
Total Flash size: 16384K with 4096 sectors9.0 to 64
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHztroller
ohci_hc
Main Thread: TP0ew USB bus regis
Memory Test Passed number 2
Total Memory: 67108864 bytes (64MB)
ohci_hcd 00
Boot Address: 0xb8000000m 0x1
Boot delay (0-9 seconds) : 1
Serial:
Board Id (0-7) : 96328A-134
ttyS0 at MMIO 0xb000
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:1f:8f:1e:58:a2
bcmxtmrt:
PSI Size (1-64) KBytes : 48ce v0.3 Jun 20 2
Enable Backup PSI [0|
*** Press any key to stop auto run (1 seconds) ***
Initializing XFRM netlink socket
Auto run second count down: 0
NET: Registered protocol fam
Booting from only image (0xb8010000) ...NET: Registered protocol family 15
Code Address: 0x80010000, Entry Address: 0x80014230e
Ebtables v2.0 registered
Decompression OK!
ebt_time re
Entry at 0x80014230
ebt_ftos re
Closing network.
ebt_w
Disabling Switch ports.
802.1
Flushing Receive Buffers...ar <greearb@candelatech.com
0 buffers found.
Closing DMA Channels.
All bugs adde
Starting program at 0x80014230hat.com>
Linux version 2.6.30 (lijf@KZ-RDDVM-UBUNTU) (gcc vquashfs filesys
DMA 0x00000000 -> 0x00001000ding drivers and kernel modules...
Normal 0x00001000 -> 0x00003f00
CT_HOTPLUG_MONITOR
Movable zone start PFN for each nodeary' taints kernel.
early_node_map active PFN rangesDisabling lock debugging due to ker
0: 0x00000000 -> 0x00003f00
Broadcom
On node 0 totalpages: 16128er v2.1 Jun 11 2010 15:27:4
free_area_init_node: node 0, pgdat 803811c0, node_mem_map 810000
>
NBUFF v1.0 Ini
Built 1 zonelists in Zone order, mobility grouping on.Total pages: 16002ry
adsl: adsl_init entry
Kernel command line: root=31:0 ro noinitrd console=ttyS0,1152007:12:45
wait instruction: enabled tx BDs at 0xa3960000
Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.0
ETH Init: 400 rx BDs at 0xa
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes####### switch_port_phyid=1
RCU-based detection of stalled CP
######## ethsw_init_table:95 ####### switch_port_phyid[
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
/proc/buffer16 created
dgasp: kerSy
Memory: 59980k/64512k available (2725k kernel code, 4512k reserved, 803k data, 1
===== Found Interface name mapping : 96328A-134 =====
24k init, 0k highmem)
Calibrating delay loop... 319.48 BogoMIPS (lpj=159744)
eth1: MAC Address: 00:1F:8F:1E:58:
Mount-cache hash table entries: 512
eth2: MAC Address: 00:1F:8F:1E:5
net_namespace: 816 bytes
eth3: MA
NET: Registered protocol family 16
eth0
Total Flash size: 16384K with 4096 sectors
wl0:
pci 0000:00:09.0: reg 10 32bit mmio: 6L02.0
pci 0000:00:0a.0: reg 10 32bit mmio: registered
pci 0000:01:00.0: PME# supported from D0 D3hot
Broadcom 802.1Q VLAN Interface, v
pci 0000:01:00.0: PME# disabled
usbcore: registered new
pci 0000:01:00.0: MEM window: 0x10f00000-0x10ffffffoption
pci 0000:01:00.0: PREFETCH window: disabled
===== Co
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
######## bcm63xx_enet_open:10
BLOG v2.1 Initializedddr=0 phyport:0 0
NET: Registered protocol family 8
br
NET: Registered protocol family 20 state
NET: Registered protocol family 2d promiscuous
TCP reno registered
NET: Registered protocol family 1
device wl0 entered promiscuo
squashfs: version 4.0 (2009/01/31) Phillip Lougheraemon is running
optarg=0
squashfs: version 4.0 with LZMA457 ported by BRCMpback socket 4
fuse init (API version 7.11) entering forwarding state
msgmni has been set to 117
s rea
io scheduler noop registered
BcmAdsl_Initializ
io scheduler deadline registered (de
Driver 'sr' needs updating - please use bus_type methodss at 0xa2fdf000
XTM In
PPP generic driver version 2.4.2
mo
PPP Deflate Compression module registered
CT_ATCPOLL:e
PPP BSD Compression module registered134:Can't open proc file /var/
NET: Registered protocol family 24
bcm963xx_mtd driver v1.0
iptables v1.4.0: can't
File system address: 0xb8010100r': iptables who? (do you
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
need to insmod?)
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
wl0.1
usb usb1: configuration #1 chosen from 1 choice
wl0.2 (): not using net_
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detectede_ops yet
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Drled state
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 0x2b01
wlctl: Unsupported
d
ohci_hcd 0000:00:09.0: irq 49, io mem 0x10002600
br0: port 5(wl0) entering disable
usb usb2: configuration #1 chosen from 1 choicedevice wl0 entered promiscuous mode
hub 2-0:1.0: USB hub found: port 5(wl0) entering for
hub 2-0:1.0: 1 port detected
R
usbcore: registered new interface driver usblp
ssk:error:23.174:c
Initializing USB Mass Storage driver...om up->down, send even
usbcore: registered new interface driver usb-storage
t msg
USYN
ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
DATA
L12F
MAIN
CFE version 1.
ttyS1 at MMIO 0xb0000120 (irq = 47) is a BCM63XX
Bu
bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Jun 20 2011 19:08:37
Copyright (C) 2000-2009 Broadcom Corporation.
Broadcom Logger v0.1 Sep 28 2010 17:12:39 Serial flash device: name MX25L128, id 0
Mirror/redirect action on
u32 classifier
input device check onith 4096 sectors
Actions configured
Chip ID: BC
TCP cubic registered, DDR: 320MHz, Bus:
Initializing XFRM netlink socket
NET: Registered protocol family 17mory Test Passed
Loading drivers and kernel modules...
Main Thread Number
CT_HOTPLUG_MONITOR
pktflow: module license 'Proprietary' taints kernel.
*** Press any k
Disabling lock debugging due to kernel taint
Aut
Broadcom Packet Flow CacheChar Driver v2.1 Jun 11 2010 15:27:43 Registered<2420xb8010000) ...
Code Address: 0x80010000
>E
NBUFF v1.0 Initialized0
Broadcom Packet Flow Cache learning via BLOG enabled.
Entry at 0x80014230
Cl
Created Proc FS /procfs/fcacheDisabling Switch ports.
Broadcom Packet Flow Cache registered with netdev chain
0 buffers found.
Closin
/proc/buffer16 createdx00003f00
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
free_area_init_node: node 0, pgdat 80
===== Found Interface name mapping : 96328A-134 =====
DMA zone:
eth0: MAC Address: 00:1F:8F:1E:58:A3
DMA zone:
eth1: MAC Address: 00:1F:8F:1E:58:A2
DMA zone: 4064 pages, LIF
eth2: MAC Address: 00:1F:8F:1E:58:A4
Normal zone: 94 pages use
eth3: MAC Address: 00:1F:8F:1E:58:A5
Normal zone: 11938
eth0 Link UP 100 mbps full duplex
Built 1
message received before monitor task is initialized kerSysSendtoMonitorTask
Kernel co
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)15200
PCI: Setting latency timer of device 0000:02:00.0 to 64
Primary instruction cache 32kB, VIPT, 4
usbcore: registered new interface driver usbserial_generic)
Calibrating delay loop... 319.48 Bo
usbserial: USB Serial Driver core
USB Serial support registered fories
option: v0.7.2:USB Driver for GSM modems 16384K with 4096 sectors
===== Comtrend Release Version A731-406CTL-C01_R04 =====h io_map_base unset
device eth0 entered promiscuous moder with io_map_base unset
######## bcm63xx_enet_open:1011 ####### dev->base_addr=0 phyport:0 0
SCSI subsystem initialized
br0: port 1(eth0) entering forwarding statece driver usbfs
device eth1 entered promiscuous moded new interface driver hub
######## bcm63xx_enet_open:1011 ####### dev->base_addr=1 phyport:0 1ver usb
pci 0000:00:09.0: r
device eth2 entered promiscuous mode6ff]
######## bcm63xx_enet_open:1011 ####### dev->base_addr=2 phyport:1 210002500-0x100025ff]
device wl0 entered promiscuous mode
pci 0000:02
WLmngr Daemon is running
optarg=0 shmId=000.0: PCI bridge
wlevt_init@107: opened loopback socket 4
pci 00
wlevt ibr0: port 5(wl0) entering forwarding state
pci 0000:01:00.0: MEM wi
s ready for new msg...ffff
BcmAdsl_Initialize=0xC019F108, g_pFnNotifyCallback=0xC01D0854CH window: disabled
pSdramPHY=0xA3FFFFF8, 0x0 0x001:00.0 (0000 -> 0002)
AdslCoreSharedMemInit: shareMemAvailable=491424etting latency timer of device 0000:01:00.0 to
AdslCoreHwReset:AdslOemDataAddr = 0xA3F69564
BLOG v2.1 Initialized
Version Number of EOC:406CTL-C01_amil
CT_ATCPOLL:error:18.517:getAvailableUsbDongleList:134:Can't open proc file /var/ash table entries: 2048 (order: 1, 8192 bytes)
donglemap2
iptables v1.4.0: can't initialize iptables table `filter': iptables who? (do you
TCP reno registered
NET: Re
need to insmod?)family 1
Perhaps iptables or your kernel needs to be upgraded.1/31) Phillip Lougher
iptables v1.4.0: can't initialize iptables table `mangle': iptables who? (do you
fuse init (API version 7.11)
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
wl0.1 (): not using net_device_ops yet
wl0.2 (): not using net_device_ops yet
wl0.3 (): not using net_device_ops yet
br0: port 5(wl0) entering disabled state
There is no Predefined DevicePin in CFE
WPS Device PIN = 62327145
Setting SSID: "Comtrend_58A2"
Setting SSID: "wl0_Guest1"
Setting SSID: "wl0_Guest2"
Setting SSID: "wl0_Guest3"
Chanspec set to 0x2b01
wlctl: Unsupported
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
Reaped 792
UPnP daemon is ready to run
ssk:error:23.203:checkDongleState:190:Wan link(3G) went from up->down, send even
t msg
ssk:error:23.204:checkDongleState:220:3G WAN not configured 人都说猫有九条命，不假我的ha910-n猫起死回生了，感谢二楼的朋友，连接ttl该一下cfe参数就好了，不过我的部分参数是从猫后面的标签上找到的，当时刷的是论坛上AR-5382u_CTL_cfe_fs_kernel.rar，改好fce后正常，不过这个固件是e文的，设置有一点小麻烦%…… 我的到现在TTL都无法显示啊，都试过了。 极地枫 发表于 2012-10-5 16:32 static/image/common/back.gif
我的到现在TTL都无法显示啊，都试过了。
刷不带cfe的固件一般不会刷坏的，你刷的是什么固件
用超级终端，com口要设置正确 不行，我现在用编程器刷都不行，我是黑色的那种机型。 估计坏了，我ttl修复了，选第4像 我的跟楼主一样了，我的RG100A-BA
页:
[1]
2