DB120WG openwrt PPPOE 连不上，没办法，请教各位了
网络是20M电信光纤，猫是光纤猫，网线接其他3口电脑都能正常拨号，然后拿一根网线连猫口跟 DB120 的4口
其他吗就按照教程配置 ETH0PPPOE 拨号，但总是拨不上，信息如下
Jan1 08:00:08 OpenWrt user.warn kernel: Please be patient, while OpenWrt loads ...
Jan1 08:00:08 OpenWrt user.info kernel: mini_fo: using base directory: /
Jan1 08:00:08 OpenWrt user.info kernel: mini_fo: using storage directory: /overlay
Jan1 08:00:10 OpenWrt user.info kernel: bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1
Jan1 08:00:10 OpenWrt user.info sysinit: udhcpc (v1.15.3) started
Jan1 08:00:11 OpenWrt user.info kernel: eth1: link forced UP - 100/full - flow control off/off
Jan1 08:00:11 OpenWrt user.info kernel: device eth1 entered promiscuous mode
Jan1 08:00:11 OpenWrt user.info kernel: br-lan: port 1(eth1) entering forwarding state
Jan1 08:00:13 OpenWrt user.info kernel: Compat-wireless backport release: compat-wireless-2010-06-04-4-gf135eab
Jan1 08:00:13 OpenWrt user.info kernel: Backport based on wireless-2.6.git v2.6.35-rc2-47270-ge46da0f
Jan1 08:00:14 OpenWrt user.info sysinit: 0.openwrt.pool.ntp.org: Unknown host
Jan1 08:00:14 OpenWrt user.info sysinit: 1.openwrt.pool.ntp.org: Unknown host
Jan1 08:00:14 OpenWrt user.info sysinit: 2.openwrt.pool.ntp.org: Unknown host
Jan1 08:00:14 OpenWrt user.info sysinit: 3.openwrt.pool.ntp.org: Unknown host
Jan1 08:00:14 OpenWrt user.info sysinit: Sending discover...
Jan1 08:00:14 OpenWrt user.info kernel: cfg80211: Calling CRDA to update world regulatory domain
Jan1 08:00:16 OpenWrt user.info kernel: cfg80211: World regulatory domain updated:
Jan1 08:00:16 OpenWrt user.info kernel: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jan1 08:00:16 OpenWrt user.info kernel: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jan1 08:00:16 OpenWrt user.info kernel: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Jan1 08:00:16 OpenWrt user.info kernel: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Jan1 08:00:16 OpenWrt user.info kernel: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jan1 08:00:16 OpenWrt user.info kernel: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jan1 08:00:16 OpenWrt user.notice kernel: SCSI subsystem initialized
Jan1 08:00:17 OpenWrt user.info kernel: roboswitch: Probing device eth0: Failed to enable switch
Jan1 08:00:17 OpenWrt user.info kernel: roboswitch: Probing device eth1: found a 5325! It's a 5350.
Jan1 08:00:17 OpenWrt user.info kernel: usbcore: registered new interface driver usbfs
Jan1 08:00:17 OpenWrt user.info kernel: usbcore: registered new interface driver hub
Jan1 08:00:17 OpenWrt user.info kernel: usbcore: registered new device driver usb
Jan1 08:00:17 OpenWrt user.info sysinit: Sending discover...
Jan1 08:00:18 OpenWrt user.info kernel: usbcore: registered new interface driver rtl8187
Jan1 08:00:18 OpenWrt user.info kernel: b43-phy0: Broadcom 4318 WLAN found (core revision 9)
Jan1 08:00:18 OpenWrt user.debug kernel: phy0: Selected rate control algorithm 'minstrel'
Jan1 08:00:18 OpenWrt user.info kernel: Registered led device: b43-phy0::tx
Jan1 08:00:18 OpenWrt user.info kernel: Registered led device: b43-phy0::rx
Jan1 08:00:18 OpenWrt user.info kernel: Registered led device: b43-phy0::radio
Jan1 08:00:18 OpenWrt user.info kernel: Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
Jan1 08:00:19 OpenWrt user.info kernel: NTFS driver 2.1.29 .
Jan1 08:00:19 OpenWrt user.info kernel: PPP generic driver version 2.4.2
Jan1 08:00:19 OpenWrt user.info kernel: tun: Universal TUN/TAP device driver, 1.6
Jan1 08:00:19 OpenWrt user.info kernel: tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Jan1 08:00:20 OpenWrt user.info kernel: usbcore: registered new interface driver p54usb
Jan1 08:00:20 OpenWrt user.info sysinit: Sending discover...
Jan1 08:00:21 OpenWrt user.info kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Jan1 08:00:21 OpenWrt user.info kernel: NET: Registered protocol family 24
Jan1 08:00:22 OpenWrt user.info kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan1 08:00:22 OpenWrt user.info kernel: bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
Jan1 08:00:22 OpenWrt user.info kernel: bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
Jan1 08:00:22 OpenWrt user.info kernel: bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
Jan1 08:00:22 OpenWrt user.info kernel: bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00
Jan1 08:00:22 OpenWrt user.info kernel: usb usb1: configuration #1 chosen from 1 choice
Jan1 08:00:22 OpenWrt user.info kernel: hub 1-0:1.0: USB hub found
Jan1 08:00:22 OpenWrt user.info kernel: hub 1-0:1.0: 2 ports detected
Jan1 08:00:22 OpenWrt user.warn kernel: nf_conntrack version 0.5.0 (464 buckets, 1856 max)
Jan1 08:00:22 OpenWrt user.warn kernel: CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
Jan1 08:00:22 OpenWrt user.warn kernel: nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
Jan1 08:00:22 OpenWrt user.warn kernel: sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
Jan1 08:00:24 OpenWrt user.info kernel: xt_time: kernel timezone is -0000
Jan1 08:00:24 OpenWrt user.info kernel: IMQ driver loaded successfully.
Jan1 08:00:24 OpenWrt user.info kernel: Hooking IMQ before NAT on PREROUTING.
Jan1 08:00:24 OpenWrt user.info kernel: Hooking IMQ after NAT on POSTROUTING.
Jan1 08:00:25 OpenWrt user.info kernel: ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Jan1 08:00:25 OpenWrt user.info kernel: bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
Jan1 08:00:25 OpenWrt user.info kernel: bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
Jan1 08:00:25 OpenWrt user.info kernel: bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
Jan1 08:00:25 OpenWrt user.info kernel: usb usb2: configuration #1 chosen from 1 choice
Jan1 08:00:25 OpenWrt user.info kernel: hub 2-0:1.0: USB hub found
Jan1 08:00:25 OpenWrt user.info kernel: hub 2-0:1.0: 1 port detected
Jan1 08:00:25 OpenWrt user.info kernel: uhci_hcd: USB Universal Host Controller Interface driver
Jan1 08:00:25 OpenWrt user.info kernel: usbcore: registered new interface driver usblp
Jan1 08:00:25 OpenWrt user.info kernel: usbcore: registered new interface driver usbserial
Jan1 08:00:25 OpenWrt user.info kernel: USB Serial support registered for generic
Jan1 08:00:25 OpenWrt user.info kernel: usbcore: registered new interface driver usbserial_generic
Jan1 08:00:25 OpenWrt user.info kernel: usbserial: USB Serial Driver core
Jan1 08:00:26 OpenWrt user.info kernel: Initializing USB Mass Storage driver...
Jan1 08:00:26 OpenWrt user.info kernel: usbcore: registered new interface driver usb-storage
Jan1 08:00:26 OpenWrt user.info kernel: USB Mass Storage support registered.
Jan1 08:00:26 OpenWrt user.info kernel: usbcore: registered new interface driver zd1211rw
Jan1 08:00:26 OpenWrt user.info sysinit: 'radio0' is disabled
Jan1 08:00:27 OpenWrt user.info sysinit: PHY for wifi device radio0 not found
Jan1 08:00:27 OpenWrt user.info sysinit: 'radio0' is disabled
Jan1 08:00:27 OpenWrt user.info sysinit: PHY for wifi device radio0 not found
Jan1 08:00:27 OpenWrt user.info sysinit: Loading defaults
Jan1 08:00:28 OpenWrt user.info sysinit: Loading synflood protection
Jan1 08:00:28 OpenWrt user.info sysinit: Adding custom chains
Jan1 08:00:29 OpenWrt user.info sysinit: Loading zones
Jan1 08:00:29 OpenWrt user.info sysinit: Loading forwarding
Jan1 08:00:29 OpenWrt user.info sysinit: Loading redirects
Jan1 08:00:29 OpenWrt user.info sysinit: Loading rules
Jan1 08:00:29 OpenWrt user.info sysinit: Loading includes
Jan1 08:00:29 OpenWrt user.info sysinit: Loading zone defaults
Jan1 08:00:30 OpenWrt user.notice root: adding lan (br-lan) to firewall zone lan
Jan1 08:00:31 OpenWrt cron.err crond: crond (busybox 1.15.3) started, log level 5
Jan1 08:00:31 OpenWrt authpriv.info dropbear: Running in background
Jan1 08:00:33 OpenWrt user.info sysinit: WARNING: the specified certificate and key files do not exist and the px5g generator is not available, skipping SSL setup.
Jan1 08:00:34 OpenWrt user.notice luci_dhcp_migrate: Migrating luci_ethers configuration ...
Jan1 08:00:34 OpenWrt user.notice luci_dhcp_migrate: Migrating luci_hosts configuration ...
Jan1 08:00:37 OpenWrt daemon.info dnsmasq: started, version 2.52 cachesize 150
Jan1 08:00:37 OpenWrt daemon.info dnsmasq: compile time options: IPv6 GNU-getopt no-DBus no-I18N DHCP TFTP
Jan1 08:00:37 OpenWrt daemon.info dnsmasq: using local addresses only for domain lan
Jan1 08:00:37 OpenWrt daemon.warn dnsmasq: no servers found in /tmp/resolv.conf.auto, will retry
Jan1 08:00:37 OpenWrt daemon.info dnsmasq: read /etc/hosts - 1 addresses
Jan1 08:00:37 OpenWrt user.info sysinit: enable=
Jan1 08:00:37 OpenWrt user.info sysinit: stop smb...
Jan1 08:00:37 OpenWrt user.info sysinit: killall: smbd: no process killed
Jan1 08:00:37 OpenWrt user.info sysinit: killall: nmbd: no process killed
Jan1 08:00:37 OpenWrt user.info sysinit: killall: vsftpd: no process killed
Jan1 08:00:37 OpenWrt user.info sysinit: remove file: smbpasswd
Jan1 08:00:37 OpenWrt user.info sysinit: ftp ftp
Jan1 08:00:37 OpenWrt user.info sysinit: config_user_list=ftp
Jan1 08:00:37 OpenWrt user.info sysinit: ftp:$1$b7zowEih$GXJAkwS496ikQG94m2JeA0:1400:2400:FTP users:/mnt:/bin/nologin
Jan1 08:00:37 OpenWrt user.info sysinit: /bin/smbpasswd ....
Jan1 08:00:38 OpenWrt user.info syslog: Password for 'ftp' changed
Jan1 08:00:38 OpenWrt user.info sysinit: Password for 'ftp' changed
Jan1 08:00:38 OpenWrt user.info sysinit: webuser_list= config_user_list=ftp
Jan1 08:02:19 OpenWrt user.info sysinit: killall: mlnet.byte.static: no process killed
Jan1 08:02:19 OpenWrt user.info sysinit: PID=
Jan1 08:02:19 OpenWrt user.info sysinit: sh: you need to specify whom to kill
Jan1 08:02:54 OpenWrt daemon.warn dnsmasq: failed to access /tmp/resolv.conf.auto: No such file or directory
Jan1 08:02:54 OpenWrt user.info kernel: br-lan: port 1(eth1) entering disabled state
Jan1 08:02:54 OpenWrt user.info kernel: device eth1 left promiscuous mode
Jan1 08:02:54 OpenWrt user.info kernel: br-lan: port 1(eth1) entering disabled state
Jan1 08:02:55 OpenWrt user.info sysinit: Read error: Network is down, reopening socket
Jan1 08:02:58 OpenWrt user.info kernel: eth1: link forced UP - 100/full - flow control off/off
Jan1 08:02:58 OpenWrt user.info sysinit: udhcpc: sendto: Network is down
Jan1 08:02:58 OpenWrt user.info sysinit: Read error: Network is down, reopening socket
Jan1 08:02:58 OpenWrt user.info kernel: eth1: link forced UP - 100/full - flow control off/off
Jan1 08:02:58 OpenWrt user.info kernel: device eth1 entered promiscuous mode
Jan1 08:02:58 OpenWrt user.info kernel: br-lan: port 1(eth1) entering forwarding state
Jan1 08:02:59 OpenWrt user.info kernel: bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1
Jan1 08:02:59 OpenWrt user.info kernel: bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1
Jan1 08:03:00 OpenWrt daemon.info pppd: Plugin rp-pppoe.so loaded.
Jan1 08:03:00 OpenWrt daemon.notice pppd: pppd 2.4.4 started by root, uid 0
Jan1 08:03:00 OpenWrt daemon.info dnsmasq: exiting on receipt of SIGTERM
Jan1 08:03:03 OpenWrt daemon.info dnsmasq: started, version 2.52 cachesize 150
Jan1 08:03:03 OpenWrt daemon.info dnsmasq: compile time options: IPv6 GNU-getopt no-DBus no-I18N DHCP TFTP
Jan1 08:03:03 OpenWrt daemon.info dnsmasq: using local addresses only for domain lan
Jan1 08:03:03 OpenWrt daemon.warn dnsmasq: failed to access /tmp/resolv.conf.auto: No such file or directory
Jan1 08:03:03 OpenWrt daemon.info dnsmasq: read /etc/hosts - 1 addresses
Jan1 08:03:15 OpenWrt daemon.warn pppd: Timeout waiting for PADO packets
Jan1 08:03:15 OpenWrt daemon.err pppd: Unable to complete PPPoE Discovery
Jan1 08:03:30 OpenWrt user.info kernel: br-lan: port 1(eth1) entering disabled state
Jan1 08:03:31 OpenWrt daemon.info pppd: Terminating on signal 15
Jan1 08:03:31 OpenWrt daemon.info pppd: Exit.
Jan1 08:03:31 OpenWrt user.info sysinit: Read error: Network is down, reopening socket
Jan1 08:03:34 OpenWrt user.info kernel: eth1: link forced UP - 100/full - flow control off/off
Jan1 08:03:34 OpenWrt user.info sysinit: udhcpc: sendto: Network is down
Jan1 08:03:34 OpenWrt user.info sysinit: Read error: Network is down, reopening socket
Jan1 08:03:34 OpenWrt user.info kernel: device eth1 left promiscuous mode
Jan1 08:03:34 OpenWrt user.info kernel: br-lan: port 1(eth1) entering disabled state
Jan1 08:03:34 OpenWrt user.info kernel: eth1: link forced UP - 100/full - flow control off/off
Jan1 08:03:34 OpenWrt user.info kernel: bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1
Jan1 08:03:35 OpenWrt user.info kernel: bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1
Jan1 08:03:35 OpenWrt daemon.info pppd: Plugin rp-pppoe.so loaded.
Jan1 08:03:35 OpenWrt daemon.notice pppd: pppd 2.4.4 started by root, uid 0
Jan1 08:03:36 OpenWrt daemon.info dnsmasq: exiting on receipt of SIGTERM
Jan1 08:03:39 OpenWrt daemon.info dnsmasq: started, version 2.52 cachesize 150
Jan1 08:03:39 OpenWrt daemon.info dnsmasq: compile time options: IPv6 GNU-getopt no-DBus no-I18N DHCP TFTP
Jan1 08:03:39 OpenWrt daemon.info dnsmasq: using local addresses only for domain lan
Jan1 08:03:39 OpenWrt daemon.warn dnsmasq: failed to access /tmp/resolv.conf.auto: No such file or directory
Jan1 08:03:39 OpenWrt daemon.info dnsmasq: read /etc/hosts - 1 addresses
Jan1 08:03:50 OpenWrt daemon.warn pppd: Timeout waiting for PADO packets
Jan1 08:03:50 OpenWrt daemon.err pppd: Unable to complete PPPoE Discovery
Jan1 08:04:36 OpenWrt daemon.warn pppd: Timeout waiting for PADO packets
Jan1 08:04:36 OpenWrt daemon.err pppd: Unable to complete PPPoE Discovery
Jan1 08:05:21 OpenWrt daemon.warn pppd: Timeout waiting for PADO packets
Jan1 08:05:21 OpenWrt daemon.err pppd: Unable to complete PPPoE Discovery
Jan1 08:06:06 OpenWrt daemon.warn pppd: Timeout waiting for PADO packets
Jan1 08:06:06 OpenWrt daemon.err pppd: Unable to complete PPPoE Discovery
Jan1 08:06:51 OpenWrt daemon.warn pppd: Timeout waiting for PADO packets
Jan1 08:06:51 OpenWrt daemon.err pppd: Unable to complete PPPoE Discovery
Jan1 08:07:36 OpenWrt daemon.warn pppd: Timeout waiting for PADO packets
Jan1 08:07:36 OpenWrt daemon.err pppd: Unable to complete PPPoE Discovery
Jan1 08:08:21 OpenWrt daemon.warn pppd: Timeout waiting for PADO packets
Jan1 08:08:21 OpenWrt daemon.err pppd: Unable to complete PPPoE Discovery
Jan1 08:09:06 OpenWrt daemon.warn pppd: Timeout waiting for PADO packets
Jan1 08:09:06 OpenWrt daemon.err pppd: Unable to complete PPPoE Discovery
Jan1 08:09:51 OpenWrt daemon.warn pppd: Timeout waiting for PADO packets
Jan1 08:09:51 OpenWrt daemon.err pppd: Unable to complete PPPoE Discovery
Jan1 08:10:36 OpenWrt daemon.warn pppd: Timeout waiting for PADO packets
Jan1 08:10:36 OpenWrt daemon.err pppd: Unable to complete PPPoE Discovery
Jan1 08:11:21 OpenWrt daemon.warn pppd: Timeout waiting for PADO packets
Jan1 08:11:21 OpenWrt daemon.err pppd: Unable to complete PPPoE Discovery
Jan1 08:12:06 OpenWrt daemon.warn pppd: Timeout waiting for PADO packets
Jan1 08:12:06 OpenWrt daemon.err pppd: Unable to complete PPPoE Discovery
Jan1 08:12:51 OpenWrt daemon.warn pppd: Timeout waiting for PADO packets
Jan1 08:12:51 OpenWrt daemon.err pppd: Unable to complete PPPoE Discovery
猫是 单口USB 的 S29 芯片的
刷完默认WAN 就选ETH0 没人知道吗 不是eth， pppoe会产生新的接口
页:
[1]