p-660hnu-51
最近电信赠送了华天p-660hnu-51智能猫，现在有线可以上网、电视也可以看，但是wifi无法使用，听说刷机可以解决问题，所以想着刷机，ttl线有了，而且驱动也好了，同时SecureCRT也打开画面了，但是没有用过SecureCRT，所以现在不知道怎么弄了。那位高手可以教教小弟吗？不胜感激！！！下面是我用SecureCRT打开猫时显示的内容，以供参考：HELO
CPUI
L1CI
DRAM
----
PHYS
ZQDN
PHYE
DINT
LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN
CFE version 1.2.37-104.5 for BCM96328 (32bit,SP,BE)
Build Date: Fri Oct 29 14:00:19 CST 2010 (tyrone@sw3-code-build-srv-02)
Copyright (C) 2000-2009 Broadcom Corporation.
HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
Total Flash size: 16384K with 256 sectors
Flash split 21 : AuxFS
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-0) : 96328avng
Number of MAC Addresses (1-32) : 10
Base MAC Address : 50:67:f0:b9:bc:0e
PSI Size (1-64) KBytes : 24
Enable Backup PSI : 1
System Log Size (0-256) KBytes : 16
Flash Block Size (1-128) in KBytes: 64
Auxillary File System Size Percent: 21
Main Thread Number : 0
Serial Number : 4F2005067F0B9BC0E
Password for Useradmin : wnxrv
SSID for first wireless (10-31) : ChinaNet-Gz6G
Password for first wireless (8-31): lmqvzjmx
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Wait for Multiboot Service Packet. 0
Booting from latest image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x802d3000
Decompression OK!
Entry at 0x802d3000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x802d3000
Linux version 2.6.21.5 (athlon@sw1-code-build-srv-01) (gcc version 4.2.3) #1 Tue Jan 4 13:20:29 CST 2011
HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
96328avng prom init
CPU revision is: 0002a075
Determined physical RAM map:
memory: 03f00000 @ 00000000 (usable)
On node 0 totalpages: 16128
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 94 pages used for memmap
Normal zone: 11938 pages, LIFO batch:1
Built 1 zonelists.Total pages: 16002
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (21 instructions).
Synthesized TLB load handler fastpath (33 instructions).
Synthesized TLB store handler fastpath (33 instructions).
Synthesized TLB modify handler fastpath (32 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
Using 160.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60768k/64512k available (2250k kernel code, 3728k reserved, 573k data, 96k init, 0k highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80c00000 ... 0x80d00000>
Calibrating delay loop... 317.44 BogoMIPS (lpj=158720)
Mount-cache hash table entries: 512
wait instruction: enabled
NET: Registered protocol family 16
Total Flash size: 16384K with 256 sectors
Flash split 21 : AuxFS
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Bridge: 0000:01:00.0
IO window: disabled.
MEM window: 10f00000-10ffffff
PREFETCH window: disabled.
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
BLOG v2.1 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
JFFS2 version 2.2. (C) 2001-2006 Red Hat, Inc.
fuse init (API version 7.8)
io scheduler noop registered (default)
PPP generic driver version 2.4.2
NET: Registered protocol family 24
bcm963xx_mtd driver v2.0
File system address: 0xb8010100
Registered device mtd dev Flash
Registered device mtd dev Flash
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: irq 50, io mem 0x10002500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 49, io mem 0x10002600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
brcmboard: ResetTimerExpire
SES: LED GPIO 0x8009 is enabled
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 36) is a BCM63XX
bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Jan4 2011 13:18:50
Broadcom Logger v0.1 Jan4 2011 13:17:46
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
6WIND/LSIIT IPv6 multicast forwarding 0.1 plus PIM-SM/SSM with *BSD API
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Initializing MCPD Module
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 96k freed
init started:BusyBox v1.00 (2011.01.04-05:22+0000) multi-call binary
BusyBox v1.00 (2011.01.04-05:22+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
pktflow: module license 'Proprietary' taints kernel.
Broadcom Packet Flow CacheChar Driver v2.1 Dec9 2009 10:05:58 Registered<242>
NBUFF v1.0 Initialized
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Constructed Broadcom Packet Flow Cache v2.1 Dec9 2009 10:05:56
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
IPv6: add_dev failed for dsl0
Broadcom BCM6328B0 Ethernet Network Device v0.1 Jan4 2011 13:17:49
KLOB extended to 2 pools
KLOB extended to 3 pools
KLOB extended to 4 pools
KLOB extended to 5 pools
KLOB extended to 6 pools
KLOB extended to 7 pools
KLOB extended to 8 pools
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
eth0: MAC Address: 50:67:F0:B9:BC:0E
eth1: MAC Address: 50:67:F0:B9:BC:0E
eth2: MAC Address: 50:67:F0:B9:BC:0E
eth3: MAC Address: 50:67:F0:B9:BC:0E
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:02:00.0 to 64
wl:srom not detected,using main memory mapped srom info(wombo board)
wl0: Broadcom BCM4313 802.11 Wireless Controller 5.60.104.0.cpe4.404.ct.2(WLTEST)
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
p8021ag: p8021ag_init entry
===== Release Version 4.04L.CT_01 (build timestamp 110121_1723) =====
Adjust WLAN Configuration, has configuration , num , defaultnum
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3024 buckets, 24192 max)
ip6_tables: (C) 2000-2006 Netfilter Core Team
ssk:error:9.451:insertModuleByName:512:ERROR!! ip6t_LOG.ko is not in module information list
ip_tables: (C) 2000-2006 Netfilter Core Team
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
registerInterestWriteSyslogEvent for 0x10000862 succeeded
ssk:error:11.790:rutPMap_associateWanIntfWithBridge:230:could not find network obj of InternetGatewayDevice.WANDevice.1.WANConnectionDevice.2.WANIPConnection.1, ret=9804
ssk:error:11.790:rcl_l2BridgingFilterObject:221:could not associate wan intf with bridge, ret=9804
ssk:error:11.790:mdm_activateObjects:599:rcl handler reports error=9804 on Filter {10}
ssk:error:11.792:rutPMap_associateWanIntfWithBridge:230:could not find network obj of InternetGatewayDevice.WANDevice.1.WANConnectionDevice.3.WANIPConnection.1, ret=9804
ssk:error:11.792:rcl_l2BridgingFilterObject:221:could not associate wan intf with bridge, ret=9804
ssk:error:11.793:mdm_activateObjects:599:rcl handler reports error=9804 on Filter {11}
ssk:error:11.794:rutPMap_associateWanIntfWithBridge:230:could not find network obj of InternetGatewayDevice.WANDevice.1.WANConnectionDevice.4.WANIPConnection.1, ret=9804
ssk:error:11.795:rcl_l2BridgingFilterObject:221:could not associate wan intf with bridge, ret=9804
ssk:error:11.795:mdm_activateObjects:599:rcl handler reports error=9804 on Filter {12}
ssk:error:11.797:rutPMap_associateWanIntfWithBridge:230:could not find network obj of InternetGatewayDevice.WANDevice.1.WANConnectionDevice.5.WANIPConnection.1, ret=9804
ssk:error:11.797:rcl_l2BridgingFilterObject:221:could not associate wan intf with bridge, ret=9804
ssk:error:11.797:mdm_activateObjects:599:rcl handler reports error=9804 on Filter {13}
exit dns6Type DHCP dns6Serversdns6Wan
we will set #DHCP#(null)#(null)#as default dns6 servers
ADDRCONF(NETDEV_UP): eth0: link is not ready
device eth0.0 entered promiscuous mode
eth0.0: dev_set_promiscuity(master, 1)
device eth0 entered promiscuous mode
eth0.0: add 33:33:00:00:00:01 mcast address to master interface
eth0.0: add 01:00:5e:00:00:01 mcast address to master interface
ADDRCONF(NETDEV_UP): eth0.0: link is not ready
ADDRCONF(NETDEV_UP): eth1: link is not ready
bridge br2 does not exist!
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
Cannot find device "br2"
eth1.0: add 33:33:00:00:00:01 mcast address to master interface
eth1.0: add 01:00:5e:00:00:01 mcast address to master interface
ADDRCONF(NETDEV_UP): eth1.0: link is not ready
ADDRCONF(NETDEV_UP): eth2: link is not ready
device eth2.0 entered promiscuous mode
eth2.0: dev_set_promiscuity(master, 1)
device eth2 entered promiscuous mode
eth2.0: add 33:33:00:00:00:01 mcast address to master interface
eth2.0: add 01:00:5e:00:00:01 mcast address to master interface
ADDRCONF(NETDEV_UP): eth2.0: link is not ready
ADDRCONF(NETDEV_UP): eth3: link is not ready
device eth3.0 entered promiscuous mode
eth3.0: dev_set_promiscuity(master, 1)
device eth3 entered promiscuous mode
eth3.0: add 33:33:00:00:00:01 mcast address to master interface
eth3.0: add 01:00:5e:00:00:01 mcast address to master interface
ADDRCONF(NETDEV_UP): eth3.0: link is not ready
setsockopt - MRT6_INIT
can't get Addr: Cannot assign requested address
error can't get ip addr by idxsetsockopt - MRT6_INIT
eth1.0: dev_set_promiscuity(master, 1)
device eth1 entered promiscuous mode
device eth1.0 entered promiscuous mode
can't join mcast group
setsockopt - MRT6_INIT
BcmAdsl_Initialize=0xC00B0708, g_pFnNotifyCallback=0xC00D0CF4
pSdramPHY=0xA3FFFFF8, 0x2090CC38 0xD896008
dhcpd:error:15.793:set_iface_config_defaults:424:SIOCGIFADDR failed on br1!
AdslCoreSharedMemInit: shareMemAvailable=491424
AdslCoreHwReset:AdslOemDataAddr = 0xA3F69564
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
Active defaultGateway6 =
backup_psi_number_blk=1 result=24576
WLmngr Daemon is running
optarg=0 shmId=0
tyrone debug: After This we will not think it is first boot
WEBUI Operation WPS Type is NONE, interface number is
WEBUI Operation WPS Type is NONE, interface number is
WEBUI Operation WPS Type is NONE, interface number is
WEBUI Operation WPS Type is NONE, interface number is
There is no Predefined DevicePin in CFE
WPS Device PIN = 21382031
ssk:error:18.859:processWatchWanConnectionMsg:1260:Enter processWatchWanConnectionMsg
device wl0 is not a slave of br0
interface wl0.1 does not exist!
interface wl0.2 does not exist!
interface wl0.3 does not exist!
backup_psi_number_blk=1 result=24576
Setting SSID: "ChinaNet-Gz6G"
Setting SSID: "ChinaNet-wl2"
Setting SSID: "ChinaNet-wl3"
Setting SSID: "ChinaNet-wl4"
smd:error:20.711:interest_register:126:different match data fields for same eid 1, ignore new matchData
wlctl: Unsupported
chanspec 0x2b0b selected
device wl0 entered promiscuous mode
device wl0.1 entered promiscuous mode
device wl0.2 entered promiscuous mode
device wl0.3 entered promiscuous mode
br0: port 4(wl0) entering learning state
br0: topology change detected, propagating
br0: port 4(wl0) entering forwarding state
Reaped 871
UPnP daemon is ready to run
BCM6328方案的机器，下载区有一些第三方固件你可以看看。刷机有风险，请小心。 *** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1
login:
login:
login:telecomadmin
Password:
web info: Waiting for connection on socket 0.
CFE> d
到这里傻了，看了好多贴子，但是还是对SecureCRT不了解，高人可以指导小弟吗？小弟是个信息技术教师，不想误人子弟，总想多学习学习学习，小弟拜托了！！！！ 怎么没人支持呢？？？？？？？？ 期待解决问题的大侠出现？？？、、??????? LZ可以试试登陆用户名和密码都为root，一般的配置文件都会在/etc里面，烤到u盘上再查看其中的内容 dimstar666 发表于 2012-5-13 20:41 static/image/common/back.gif
LZ可以试试登陆用户名和密码都为root，一般的配置文件都会在/etc里面，烤到u盘上再查看其中的内容
能具体些吗？怎么在/etc里面拷贝文件呢？ 插上u盘，用ttl登陆，用户名和密码都是root，如果登陆成功，用命令行拷贝
1 cd /etc2 cp board.conf /mnt/usb1_1
然后你应该能在u盘上看到那个文件了，里边有密码
dimstar666 发表于 2012-5-15 12:56 static/image/common/back.gif
插上u盘，用ttl登陆，用户名和密码都是root，如果登陆成功，用命令行拷贝
1 cd /etc2 cp board.conf /mn ...
用root登陆不了， 华天p-660hnu-51本身有带WIFI，不存在无线不能用的问题。建议用超级帐号密码进去看一下，无线有无开启； 还有就是WIFI开关有没开。
页:
[1]
2