求助.BCM6338刷机后启动不了
PING 192.168.1.1不通.用securecrt .通过TTL线可以显示
help
logout
reboot
adsl
atm
brctl
cat
ddns
df
dumpcfg
echo
ifconfig
kill
arp
defaultgateway
dhcpserver
dns
lan
passwd
ppp
remoteaccess
restoredefault
route
save
swversion
wan
ping
ps
pwd
sntp
sysinfo
tftp
但又不进不了CFE
想问一下怎么能让它PING通.或者在TTL的TFTP下升级固件. 你刷什么固件？你ttl显示的内容都是设备正常启动后才有的。都是已经正常运行后设备的telnet模式了。 YES东 发表于 2012-4-17 22:35 static/image/common/back.gif
你刷什么固件？你ttl显示的内容都是设备正常启动后才有的。都是已经正常运行后设备的telnet模式了。
RTA1320_REV2_FW_3.65p_NZ分解出的CFE加TP LINK的8810固件.
因为想刷网件dm111p-v364p.刷不了就想把1320的CFE刷进去先.但那个也刷不了就组合了固件
但用TTL连接怎么也不能使它停下来进CFE
Boot Address 0xbfc00000
Ethernet Switch
config using SSB_1
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id Name : RTA1320
Psi size in KB : 24
Number of MAC Addresses (1-32) : 11
Ethernet MAC Address : 00:23:c9:28:01:97
Serial Number : y
Memory size in MB : 8
CMT Thread Number : 0
==== Press space key to stop auto run (1 seconds) ====
Auto run second count down(before hit space key): 0
Code Address: 0x80010000, Entry Address: 0x8017b018
Decompression OK!
Entry at 0x8017b018
Closing network.
Starting program at 0x8017b018
Linux version 2.6.8.1 (root@localhost.localdomain) (gcc version 3.4.2) #1 Sun Mar 20 04:33:43 CST 2011
spi flash init, device_id is 276
Serial flash device: name S25FL016A, id 0x0114, size 2048KB
Total Flash size: 2048K with 32 sectors
***Board id is not set****: Using the default PSI size: 24
RTA1320 prom init
CPU revision is: 00029010
Determined physical RAM map:
memory: 007a0000 @ 00000000 (usable)
On node 0 totalpages: 1952
DMA zone: 1952 pages, LIFO batch:1
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd
brcm mips: enabling icache and dcache...
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 8kB 2-way, linesize 16 bytes.
PID hash table entries: 32 (order 5: 256 bytes)
Using 120.000 MHz high precision timer.
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 6048k/7808k available (1265k kernel code, 1740k reserved, 182k data, 64k init, 0k highmem)
Calibrating delay loop... 239.20 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...unavailable.
NET: Registered protocol family 16
Can't analyze prologue code at 8014add4
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v1.0
brcmboard: brcm_board_init entry
proid 50 52 49 44 00 00 18 c2
pro id 18c2
bcm963xx_serial driver v2.0
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 1024)
NET: Registered protocol family 1
NET: Registered protocol family 17
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 64k freed
init started:BusyBox v1.00 (2011.03.19-20:35+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
BusyBox v1.00 (2011.03.19-20:35+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
atmapi: module license 'Proprietary' taints kernel.
blaadd: blaa_detect entry
adsl: adsl_init entry
Broadcom BCMPROCFS v1.0 initialized
BCM63xx_ENET board id not set
insmod: cannot insert `/lib/modules/2.6.8.1/extra/bcm_enet.ko': Success (19): Success
BcmAdsl_Initialize=0xC0063218, g_pFnNotifyCallback=0xC0079644
pSdramPHY=0xA07FFFF8, 0x4C15433C 0x73AC9E89
AdslCoreHwReset: AdslOemDataAddr = 0xA07FBB64
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
==> Bcm963xx Software Version: 0.1.0.1 build 110320 Rel.16434n <==
ulId is 00002101, vpi is 00, vci is 0021, conId is 01
pvc2684d: Interface "nas_0_33" created sucessfully
pvc2684d: Communicating over ATM 0.0.33, encapsulation: LLC
device nas_0_33 entered promiscuous mode
pvc2684d: Interface "nas_0_35" created sucessfully
pvc2684d: Communicating over ATM 0.0.35, encapsulation: LLC
ulId is 00002301, vpi is 00, vci is 0023, conId is 01
device nas_0_35 entered promiscuous mode
ulId is 08002301, vpi is 08, vci is 0023, conId is 01
pvc2684d: Interface "nas_8_35" created sucessfully
pvc2684d: Communicating over ATM 0.8.35, encapsulation: LLC
device nas_8_35 entered promiscuous mode
pvc2684d: Interface "nas_8_48" created sucessfully
pvc2684d: Communicating over ATM 0.8.48, encapsulation: LLC
ulId is 08003001, vpi is 08, vci is 0030, conId is 01
device nas_8_48 entered promiscuous mode
begin tddp
机子已经正常启动了呀，你是什么型号的设备呀`~ 天邑 96338L-2M-8M 1.0.37-10.
ping不通 bangding1111 帮顶。。。
希望楼主早日解决 lin24 发表于 2012-4-18 06:46 static/image/common/back.gif
RTA1320_REV2_FW_3.65p_NZ分解出的CFE加TP LINK的8810固件.
因为想刷网件dm111p-v364p.刷不了就想把1320 ...
到==== Press space key to stop auto run (1 seconds) ====
这个位置的时候按回车或者esc。也可以试试按住reset开机。 本帖最后由 lin24 于 2012-4-18 21:40 编辑
YES东 发表于 2012-4-18 13:49 static/image/common/back.gif
到==== Press space key to stop auto run (1 seconds) ====
这个位置的时候按回车或者esc。也可以试试按 ...
谢谢大家的回复.刚刚用编辑器把CFE写进去.再用TTL配置一下.刷了TP的固件可以用了...
CFE version 1.0.37-10.1 for BCM96338 (32bit,SP,BE)
Build Date: Fri Nov 16 23:17:17 HKT 2007 (root@lijian)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbfc00000
Initializing Arena.
Initializing Devices.
Serial flash device: name S25FL016A, id 0x0114, size 2048KB
*** Board is not initialized properly ***
Press:<enter> to use current value
'-' to go previous parameter
'.' to clear the current value
'x' to exit this command
96338SV ------- 0
96338L-2M-8M ------- 1
96338L-65-2M-8M------- 2
96338W ------- 3
96338W-20P2 ------- 4
96338E ------- 5
96338E4 ------- 6
96338E4-20P2 ------- 7
96332CG ------- 8
Board Id (0-8) :1
Number of MAC Addresses (1-32) :012
Base MAC Address :00:00:00:00:00:0000:23C9:28:01:27
Invalid MAC address format:eg. 12:34:56:ab:cd:ef or 123456abcdef;Try again!
Base MAC Address :00:00:00:00:00:0000:23:c9:28:01:27
PSI Size (1-64) KBytes :24
100 MB Full-Duplex (auto-neg)
CPU type 0x29010: 240MHz
Total memory: 8388608 bytes (8MB)
Total memory used by CFE:0x80401000 - 0x80528630 (1209904)
Initialized Data: 0x8041DE90 - 0x8041FE60 (8144)
BSS Area: 0x8041FE60 - 0x80426630 (26576)
Local Heap: 0x80426630 - 0x80526630 (1048576)
Stack Area: 0x80526630 - 0x80528630 (8192)
Text (code) segment: 0x80401000 - 0x8041DE8C (118412)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
** Flash image not found. **
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-8) : 96338L-2M-8M
Number of MAC Addresses (1-32) : 12
Base MAC Address : 00:23:c9:28:01:97
PSI Size (1-64) KBytes : 24
web info: Waiting for connection on socket 0.
web info: Waiting for connection on socket 1.
web info: Waiting for connection on socket 0.
web info: Upload 1889617 bytes, Broadcom image format.
CFE>
Flashing CFE: .
页:
[1]