机顶盒（EC1308）通过无线路由连接光猫（RG200O）如何设置
本帖最后由 qoofish 于 2012-3-24 14:11 编辑RG200O已开启SSID2，详细的配置文件见二楼；
将RG200O的SSID2与Other_B连接绑定。
无线路由通过Repeater方式与SSID2桥接；
认证方式选择的WPA-PSK，WPA加密选的是TKIP，密码填写的12345678。
机顶盒（EC1308）连接到无线路由的LAN口
无论用DHCP还是PPPOE，机顶盒都不能连接，前者显示无法获得链接地址，后者显示重拨等待。
但如果机顶盒与RG200O的LAN2口直连，选择DHCP方式，则能正常播放。
求真相！！！
请各位大大指正我的设置方法。 本帖最后由 qoofish 于 2012-3-24 14:21 编辑
求真相，求帮忙啊
===============RG200O-CA 关于SSID2的相关配置文件=================
<WLANConfiguration instance="2">
<Enable>TRUE</Enable>
<Name>wl0.1</Name>
<MaxBitRate>54</MaxBitRate>
<Channel>1</Channel>
<SSID>ChinaNet-iTV-1234</SSID>
<BeaconType>WPA</BeaconType>
<BasicEncryptionModes>None</BasicEncryptionModes>
<RadioEnabled>TRUE</RadioEnabled>
<WMMSupported>TRUE</WMMSupported>
<UAPSDSupported>TRUE</UAPSDSupported>
<WMMEnable>TRUE</WMMEnable>
<X_BROADCOM_COM_BaseCfg_MBSSNumOfAdapter>4</X_BROADCOM_COM_BaseCfg_MBSSNumOfAdapter>
<X_BROADCOM_COM_BaseCfg_Info>ap led wme 802.11d 802.11h mbss16 afterburner ampdu amsdurx amsdutx delaymode wmf rxchain_pwrsave radio_pwrsave </X_BROADCOM_COM_BaseCfg_Info>
<X_BROADCOM_COM_BaseCfg_CoreRev>23</X_BROADCOM_COM_BaseCfg_CoreRev>
<X_BROADCOM_COM_BaseCfg_Ver>5.60.120.11.cpe4.402</X_BROADCOM_COM_BaseCfg_Ver>
<X_BROADCOM_COM_BaseCfg_MBSSIDSupported>1</X_BROADCOM_COM_BaseCfg_MBSSIDSupported>
<X_BROADCOM_COM_BaseCfg_AburnSupported>1</X_BROADCOM_COM_BaseCfg_AburnSupported>
<X_BROADCOM_COM_BaseCfg_AmpduSupported>1</X_BROADCOM_COM_BaseCfg_AmpduSupported>
<X_BROADCOM_COM_BaseCfg_AmsduSupported>1</X_BROADCOM_COM_BaseCfg_AmsduSupported>
<X_BROADCOM_COM_BaseCfg_WmfSupported>1</X_BROADCOM_COM_BaseCfg_WmfSupported>
<X_BROADCOM_COM_VirtualIfCfg_EnableWmf>1</X_BROADCOM_COM_VirtualIfCfg_EnableWmf>
<X_BROADCOM_COM_PhyType>n</X_BROADCOM_COM_PhyType>
<WEPKey instance="1"><WEPKey>1234567890123</WEPKey></WEPKey>
<WEPKey instance="2"><WEPKey>1234567890123</WEPKey></WEPKey>
<WEPKey instance="3"><WEPKey>1234567890123</WEPKey></WEPKey>
<WEPKey instance="4"><WEPKey>1234567890123</WEPKey></WEPKey>
<WEPKey nextInstance="5" ></WEPKey>
<PreSharedKey instance="1"><PreSharedKey>12345678</PreSharedKey></PreSharedKey>
<PreSharedKey nextInstance="2" ></PreSharedKey>
<WPS><Enable>TRUE</Enable></WPS>
<X_BROADCOM_COM_Wds><Static instance="1"></Static>
<Static instance="2"></Static>
<Static instance="3"></Static>
<Static instance="4"></Static>
<Static nextInstance="5" ></Static>
</X_BROADCOM_COM_Wds>
</WLANConfiguration>
===============================END================================
=========================RG200O-CA设置的相关截图=======================
===============================END================================
有lan2口可以用不就行了，你查下lan2口有没有特别用法？ 改成不加密试试 解决了吗？也想知道啊
页:
[1]