关于大亚DB120-B1刷机固件的问题
设备是：大亚DB120-b1打算刷到2760U 1.07
参照
1、手动输入http://192.168.1.1/index.html，可见DB120-b1的CFE版本是 1.0.37-10.3
2、输入http://192.168.1.1/upload.cgi，在WEB下升级到公版的固件（刷后用户名和密码是user）
vw官方.rar (3.78 MB, 下载次数: 385)
3、输入http://192.168.1.1/upload.cgi，在WEB下升级下升级到博达3G中文固件(刷后用户名和密码是admin)说明书在压缩包
db-120可用博达3G1704-wg中文固件.zip (5.21 MB, 下载次数: 428)
按这个步骤刷了几次都是到了3，升级到博达的时候总是停留在升级页面，因为备有TTL线，所以几次都刷会了电信原版。
刷回原版的时候也比较奇怪，有时候是刷 了三次固件，才好的。。
后来参考了网上的其他帖子，
有一个说可以跳过博达3G，先公版然后刷1.04d的cfe，再1.07
于是杯具了。。
过程是：刷了2次公版的vw2，
刷了一次1.04 的时候，就无法进入升级页面了
web页面ping哪个口都不通。
完全启动的时候，好像是可以正常启动
power灯正常，dsl闪烁，usb1、2常亮
进入cfe的时候power灯红色
网线ping1234口都不通。
cfe下的各个命令都可以用
在超级终端完全启动完成后，可以用admin进入
ping192.168.1.1可以通
以下是完全启动的显示。求个分析
CFE version 1.0.37-6.5 for BCM96358 (32bit,SP,BE)
Build Date: Sun Apr 26 00:57:24 CST 2009 (root@MOD6538)
Copyright (C) 2000-2005 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x80528280 (1208960)
Initialized Data: 0x8041DB50 - 0x8041F980 (7728)
BSS Area: 0x8041F980 - 0x80426280 (26880)
Local Heap: 0x80426280 - 0x80526280 (1048576)
Stack Area: 0x80526280 - 0x80528280 (8192)
Text (code) segment: 0x80401000 - 0x8041DB4C (117580)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id Name : 96358VW2
Psi size in KB : 24
Number of MAC Addresses (1-32) : 12
Base MAC Address : 00:00:00:00:00:00
Ethernet PHY Type : External Switch Using Reverse MII
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x8031e000
Decompression OK!
Entry at 0x8031e000
Closing network.
Starting program at 0x8031e000
Linux version 2.6.21.5 (lijf@deb-vm) (gcc version 4.2.3) #7 Sun Sep 5 13:52:39 C
ST 2010
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 31 pages used for memmap
Normal zone: 3969 pages, LIFO batch:0
Built 1 zonelists.Total pages: 8033
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (21 instructions).
Synthesized TLB load handler fastpath (33 instructions).
Synthesized TLB store handler fastpath (33 instructions).
Synthesized TLB modify handler fastpath (32 instructions).
PID hash table entries: 128 (order: 7, 512 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 28676k/32384k available (2236k kernel code, 3708k reserved, 888k data, 9
6k init, 0k highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80c00000 ... 0x80d00000>
Calibrating delay loop... 297.98 BogoMIPS (lpj=148992)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Total Flash size: 16384K with 128 sectors
File system address: 0xbe020100
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
BLOG v1.0 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
NTFS driver 2.1.28 .
fuse init (API version 7.8)
io scheduler noop registered (default)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
bcm963xx_mtd driver v1.0
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: irq 18, io mem 0xfffe1300
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 13, io mem 0xfffe1400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
brcmboard: brcm_board_init entry
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
bcmxtmrt: Broadcom BCM6358A1 ATM Network Device v0.1 Sep5 2010 13:51:14
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 96k freed
init started:BusyBox v1.00 (2010.09.05-05:52+0000) multi-call binary
BusyBox v1.00 (2010.09.05-05:52+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
-sh: can't access tty; job control turned off
Loading drivers and kernel modules...
mknod: /var/fuse: File exists
pktflow: module license 'Proprietary' taints kernel.
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Constructed Broadcom Packet Flow Cache v0.1 Feb 26 2009 14:21:08
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Aug 17 2010 15:57:41
Config Internal PHY Through MDIO
BCM63xx_ENET: Auto-negotiation timed-out
BCM63xx_ENET: 10 MB Half-Duplex (assumed)
eth0: MAC Address: 00:00:00:00:00:00
Broadcom BCM6358A1 Ethernet Network Device v0.3 Aug 17 2010 15:57:41
KLOB extended to 2 pools
KLOB extended to 3 pools
KLOB extended to 4 pools
Config Ethernet Switch Through MDIO Pseudo PHY Interface
ethsw: found bcm5325e!
dgasp: kerSysRegisterDyingGaspHandler: eth1 registered
eth1: MAC Address: 00:00:00:00:00:01
KLOB extended to 5 pools
Broadcom BCM6358A1 USB Network Device v0.4 Aug 17 2010 15:57:46
usb0: MAC Address: 00 00 00 00 00 02
usb0: Host MAC Address: 00 00 00 00 00 03
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:01.0 to 64
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: MAC addr from system pool. id:0x776c0000
wl0: MAC Address: 00:00:00:00:00:04
wl0: Broadcom BCM4318 802.11 Wireless Controller 5.10.85.0.cpe4.402.8
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
proc file create OK for wireless lan.
===== Release Version 4.02L.03 (build timestamp 100817_1558) =====
wl_cnt= 1
rut_restartSamba: enter
rut_stopSamba: enter
rut_stopSamba: Smbd has not been started yet
.rut_stopSamba: Nmbd has not been started yet
.rut_startSamba: status = enable netBiosName=bezeq directoryName =bezeq utf8DirN
ame=bezeq charset=utf8
AlphaSmbSetConf: status = enable netBiosName=bezeq directoryName =bezeq utf8DirN
ame=bezeq charset=utf8
AlphaSmbSetConf: br0IP=192.168.1.1br0Mask=192.168.1.0
rut_startSamba: enter
device eth0 is not a slave of br0
can't add eth0 to bridge br0: Invalid argument
device eth1 is not a slave of br0
device eth1 entered promiscuous mode
br0: port 1(eth1) entering learning state
br0: topology change detected, propagating
br0: port 1(eth1) entering forwarding state
KLOB extended to 6 pools
device usb0 is not a slave of br0
device usb0 entered promiscuous mode
br0: port 2(usb0) entering learning state
br0: topology change detected, propagating
br0: port 2(usb0) entering forwarding state
WLmngr Daemon is running
optarg=0 shmId=0
I am open &async_queue = 0xc00367c0<3>kill_fasync: bad magic number in fasync_s
truct!
wlButtonInit open gpio_fasync
success
Pasync_queue->magic = 0x4601
device wl0 is not a slave of br0
device wl0 entered promiscuous mode
br0: port 3(wl0) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0) entering forwarding state
BcmAdsl_Initialize=0xC0074608, g_pFnNotifyCallback=0xC0094414
KLOB extended to 7 pools
pSdramPHY=0xA1FFFFF8, 0xFFFFFFFF 0xFFFFFFFF
AdslCoreSharedMemInit: shareMemAvailable=3552
AdslCoreHwReset:AdslOemDataAddr = 0xA1FF3FD4
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
KLOB extended to 8 pools
ip_tables: (C) 2000-2006 Netfilter Core Team
device wl0 left promiscuous mode
br0: port 3(wl0) entering disabled state
device wl0 is not a slave of br0
device wl0 entered promiscuous mode
br0: port 3(wl0) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0) entering forwarding state
interface wl0.1 does not exist!
interface wl0.2 does not exist!
interface wl0.3 does not exist!
Setting SSID "dlink"
Setting SSID "wl0_Guest1"
Setting SSID "wl0_Guest2"
Setting SSID "wl0_Guest3"
br0: port 3(wl0) entering disabled state
br0: port 3(wl0) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0) entering forwarding state
device wl0 left promiscuous mode
br0: port 3(wl0) entering disabled state
device wl0 is not a slave of br0
device wl0 entered promiscuous mode
br0: port 3(wl0) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0) entering forwarding state
device wl0.1 is not a slave of br0
device wl0.2 is not a slave of br0
device wl0.3 is not a slave of br0
delay_run start
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered. 楼主用的可能是6.5不带web升级页面的cfe，可以用“e n”命令清空cfe设置，重新设置一下，最后一项phy设置成0为lan4口升级。电脑ip设为192.168.1.100，cmd下ping 192.168.1.1,能ping通的时候就说明可以了。然后用tftp加载升级文件，路由cfe里边直接用f命令刷固件，“f 文件名” finaltank 发表于 2012-1-11 15:37 static/image/common/back.gif
楼主用的可能是6.5不带web升级页面的cfe，可以用“e n”命令清空cfe设置，重新设置一下，最后一项phy设置成 ...
谢谢，
在做了。
好像cmd下还是ping不通。
现在再查ftp的使用办法。
稍后来报告情况。。 amrtaq 发表于 2012-1-12 12:40 static/image/common/back.gif
谢谢，
在做了。
好像cmd下还是ping不通。
ftp软件是tftp32,很简单，选择好固件所在的目录就行了。相当于在本机做了一个ftp服务器 本帖最后由 amrtaq 于 2012-1-12 21:51 编辑
finaltank 发表于 2012-1-12 13:52 static/image/common/back.gif
ftp软件是tftp32,很简单，选择好固件所在的目录就行了。相当于在本机做了一个ftp服务器
cmd下ping192.168.1.1始终不通。。。能再帮我分析下么？
是在cfe下使用f命令是不是也可以？
t在引导全部完成后使用tftp下面这个命令对么？
tftp -g -t i -f xx.bin 192.168.1.100
还有这个可以用u盘接usb1直接在db120上引导么？
命令是什么呢？
刚刚生气。。用了e a
现在怎么办。。好像都不行了。。。{:soso_e101:} e a了也没关系，只要cfe能运行就不是砖，就能刷 我都是在1LAN升级... 可以刷脱机的固件吗？ CFE version 1.0.37-6.5 for BCM96358 (32bit,SP,BE)
Build Date: Tue Jan 27 11:04:51 CST 2009 (root@MOD6538)
Copyright (C) 2000-2005 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
Unknown PHY type
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x80528320 (1209120)
Initialized Data: 0x8041DB70 - 0x8041FA20 (7856)
BSS Area: 0x8041FA20 - 0x80426320 (26880)
Local Heap: 0x80426320 - 0x80526320 (1048576)
Stack Area: 0x80526320 - 0x80528320 (8192)
Text (code) segment: 0x80401000 - 0x8041DB64 (117604)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
*** Board is not initialized properly ***
Press:<enter> to use current value
'-' to go previous parameter
'.' to clear the current value
'x' to exit this command
Board Id Name (0-8)
96358M -------0
96358SV -------1
96358VW -------2
96358VW-16 -------3
96358GW-16 -------4
96358GW -------5
96358GW-A -------6
96358VW2 -------7
96358VW-A -------8 :7
页:
[1]