华勤HG100N TTL启动信息
CFE version 1.7.37-104.5 for BCM96328 (32bit,SP,BE)Build Date: Wed Aug 31 13:40:45 CST 2011 (tyrone@sw3-code-build-srv-02)
Copyright (C) 2000-2009 Broadcom Corporation.
HS Serial flash device: name MX25L32, id 0xc216 size 4096KB
Total Flash size: 4096K with 79 sectors
Flash not used for Auxillary File System
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-7) : DSL100N-B1 v2
Number of MAC Addresses (1-32) : 5
Base MAC Address : c8:6c:87:c1:42:17
PSI Size (1-64) KBytes : 20
Enable Backup PSI : 1
System Log Size (0-256) KBytes : 8
Flash Block Size (1-128) in KBytes: 64
Auxillary File System Size Percent: 0
Main Thread Number : 0
Serial Number : 41200C86C87C14217
Password for Useradmin : 2uy7d
SSID for first wireless (10-31) : ChinaNet-6hMA
Password for first wireless (8-31): dbr4pvdx
PA(e=External PA,i=Internal PA) : i
Minimal Core Max Size (0-2097152) in Bytes: 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Wait for Multiboot Service Packet. 0
Reset Button is unclicked
Booting from only image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x8021b000
Decompression OK!
Entry at 0x8021b000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x8021b000
Linux version 2.6.21.5 (tyrone@sw3-code-build-srv-02) (gcc version 4.2.3) #1 Wed
Aug 31 13:33:29 CST 2011
HS Serial flash device: name MX25L32, id 0xc216 size 4096KB
DSL100N-B1 v2 prom init
CPU revision is: 0002a075
Determined physical RAM map:
memory: 03f00000 @ 00000000 (usable)
On node 0 totalpages: 16128
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 94 pages used for memmap
Normal zone: 11938 pages, LIFO batch:1
Built 1 zonelists.Total pages: 16002
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (21 instructions).
Synthesized TLB load handler fastpath (33 instructions).
Synthesized TLB store handler fastpath (33 instructions).
Synthesized TLB modify handler fastpath (32 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
Using 160.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 61516k/64512k available (1799k kernel code, 2980k reserved, 288k data, 8
8k init, 0k highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80300000 ... 0x80400000>
Calibrating delay loop... 317.44 BogoMIPS (lpj=158720)
Mount-cache hash table entries: 512
wait instruction: enabled
NET: Registered protocol family 16
Total Flash size: 4096K with 79 sectors
Flash not used for Auxillary File System
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
PCI: Bridge: 0000:01:00.0
IO window: disabled.
MEM window: 10f00000-10ffffff
PREFETCH window: disabled.
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
BLOG v2.1 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
io scheduler noop registered (default)
PPP generic driver version 2.4.2
NET: Registered protocol family 24
bcm963xx_mtd driver v2.0
File system address: 0xb8010100
Registered device mtd dev Flash
brcmboard: brcm_board_init entry
brcmboard: ResetTimerExpire
SES: LED GPIO 0x8009 is enabled
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 36) is a BCM63XX
bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Aug 31 2011 13:31:52
Broadcom Logger v0.1 Aug 31 2011 13:30:48
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
6WIND/LSIIT IPv6 multicast forwarding 0.1 plus PIM-SM/SSM with *BSD API
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Initializing MCPD Module
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 88k freed
init started:BusyBox v1.00 (2011.08.31-05:35+0000) multi-call binary
mount: Mounting none on /proc/bus/usb failed: No such file or dir
BusyBox v1.00 (2011.08.31-05:35+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
pktflow: module license 'Proprietary' taints kernel.
Broadcom Packet Flow CacheChar Driver v2.2 Feb 22 2011 15:47:08 Registered<242
>
NBUFF v1.0 Initialized
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Constructed Broadcom Packet Flow Cache v2.2 Feb 22 2011 15:47:07
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
IPv6: add_dev failed for dsl0
Broadcom BCM6328B0 Ethernet Network Device v0.1 Aug 31 2011 13:30:50
KLOB extended to 2 pools
KLOB extended to 3 pools
KLOB extended to 4 pools
KLOB extended to 5 pools
KLOB extended to 6 pools
KLOB extended to 7 pools
KLOB extended to 8 pools
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
eth0: MAC Address: C8:6C:87:C1:42:17
eth1: MAC Address: C8:6C:87:C1:42:17
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:02:00.0 to 64
wl:srom not detected,using main memory mapped srom info(wombo board)
wl:loading /etc/wlan/bcm43130_map.bin
wl0: Broadcom BCM4313 802.11 Wireless Controller 5.60.120.3.cpe4.404.ct.0
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
141
144
===== Release Version 4.04L.CT_01 (build timestamp 110831_1333) =====
Adjust WLAN Configuration, has configuration , num , defaultnum
===> BOARD_IOCTL_SET_ALLBRIDGESAMEWITHETH_SWITCH, g_BridgeMACSameWithEth_Switch
2,ctrlParms.offset 2
update BOARD_IOCTL_SET_ALLBRIDGESAMEWITHETH_SWITCH2 successfull
Broadcom Packet Flow CacheChar Driver v2.2 Feb 22 2011 15:47:08 Unregistered<2
42>
Broadcom Packet Flow Cache learning via BLOG disabled.
Broadcom Packet Flow Cache unregistered with netdev chain
Deleted Proc FS /procfs/fcache
Active<0> = <0> - <0>
Destructed Broadcom Packet Flow Cache v2.2 Feb 22 2011 15:47:07
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3024 buckets, 24192 max)
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip6tables: No chain/target/match by that name
ip_tables: (C) 2000-2006 Netfilter Core Team
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
registerInterestWriteSyslogEvent for 0x10000862 succeeded
interface atm1.0 does not exist!
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
Cannot find device "br0"
SIOCGIFFLAGS: No such device
interface atm2.0 does not exist!
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
Cannot find device "br0"
SIOCGIFFLAGS: No such device
interface atm3.0 does not exist!
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
Cannot find device "br0"
SIOCGIFFLAGS: No such device
interface atm4.0 does not exist!
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
Cannot find device "br0"
SIOCGIFFLAGS: No such device
interface atm5.0 does not exist!
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
Cannot find device "br0"
SIOCGIFFLAGS: No such device
interface atm6.0 does not exist!
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
Cannot find device "br0"
SIOCGIFFLAGS: No such device
interface atm7.0 does not exist!
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
Cannot find device "br0"
SIOCGIFFLAGS: No such device
exit dns6Type DHCP dns6Serversdns6Wan
we will set #DHCP#(null)#(null)#as default dns6 servers
ADDRCONF(NETDEV_UP): eth0: link is not ready
device eth0.0 entered promiscuous mode
eth0.0: dev_set_promiscuity(master, 1)
device eth0 entered promiscuous mode
eth0.0: add 33:33:00:00:00:01 mcast address to master interface
eth0.0: add 01:00:5e:00:00:01 mcast address to master interface
ADDRCONF(NETDEV_UP): eth0.0: link is not ready
ADDRCONF(NETDEV_UP): eth1: link is not ready
device eth1.0 entered promiscuous mode
eth1.0: dev_set_promiscuity(master, 1)
device eth1 entered promiscuous mode
eth1.0: add 33:33:00:00:00:01 mcast address to master interface
eth1.0: add 01:00:5e:00:00:01 mcast address to master interface
ADDRCONF(NETDEV_UP): eth1.0: link is not ready
setsockopt - MRT6_INIT
BcmAdsl_Initialize=0xC0064708, g_pFnNotifyCallback=0xC0084CE4
pSdramPHY=0xA3FFFFF8, 0x0 0x0
AdslCoreSharedMemInit: shareMemAvailable=490656
AdslCoreHwReset:AdslOemDataAddr = 0xA3F69864
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
ssk:error:14.030:rcl_wanDslLinkCfgObject:295:===> layer2 ifname is atm0
ssk:error:14.033:rcl_wanIpConnObject:580:rut_getProvinceConfig, MTouch is 0
Send out CMS_MSG_CHECK_WAN_MODE event msg
ssk:error:14.042:rutPMap_addAvailableInterface:807:avail InterfaceReference Inte
rnetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANIPConnection.1 already ex
ists
ssk:error:14.076:rcl_wanDslLinkCfgObject:295:===> layer2 ifname is atm1
Send out CMS_MSG_CHECK_WAN_MODE event msg
ssk:error:14.087:rutPMap_addAvailableInterface:807:avail InterfaceReference Inte
rnetGatewayDevice.WANDevice.1.WANConnectionDevice.2.WANPPPConnection.1 already e
xists
ssk:error:14.105:rutLan_removeInterfaceFromBridge:1233:got NULL lanIfName or bri
dgeIfName
interface atm1.0 does not exist!
SIOCGIFFLAGS: No such device
ssk:error:14.324:rcl_wanDslLinkCfgObject:295:===> layer2 ifname is atm2
Send out CMS_MSG_CHECK_WAN_MODE event msg
ssk:error:14.336:rutPMap_addAvailableInterface:807:avail InterfaceReference Inte
rnetGatewayDevice.WANDevice.1.WANConnectionDevice.3.WANPPPConnection.1 already e
xists
ssk:error:14.354:rutLan_removeInterfaceFromBridge:1233:got NULL lanIfName or bri
dgeIfName
interface atm2.0 does not exist!
SIOCGIFFLAGS: No such device
ssk:error:14.551:rcl_wanDslLinkCfgObject:295:===> layer2 ifname is atm3
Send out CMS_MSG_CHECK_WAN_MODE event msg
ssk:error:14.563:rutPMap_addAvailableInterface:807:avail InterfaceReference Inte
rnetGatewayDevice.WANDevice.1.WANConnectionDevice.4.WANPPPConnection.1 already e
xists
ssk:error:14.583:rutLan_removeInterfaceFromBridge:1233:got NULL lanIfName or bri
dgeIfName
interface atm3.0 does not exist!
SIOCGIFFLAGS: No such device
ssk:error:14.781:rcl_wanDslLinkCfgObject:295:===> layer2 ifname is atm4
Send out CMS_MSG_CHECK_WAN_MODE event msg
ssk:error:14.794:rutPMap_addAvailableInterface:807:avail InterfaceReference Inte
rnetGatewayDevice.WANDevice.1.WANConnectionDevice.5.WANPPPConnection.1 already e
xists
ssk:error:14.815:rutLan_removeInterfaceFromBridge:1233:got NULL lanIfName or bri
dgeIfName
interface atm4.0 does not exist!
SIOCGIFFLAGS: No such device
ssk:error:15.014:rcl_wanDslLinkCfgObject:295:===> layer2 ifname is atm5
Send out CMS_MSG_CHECK_WAN_MODE event msg
ssk:error:15.027:rutPMap_addAvailableInterface:807:avail InterfaceReference Inte
rnetGatewayDevice.WANDevice.1.WANConnectionDevice.6.WANPPPConnection.1 already e
xists
ssk:error:15.050:rutLan_removeInterfaceFromBridge:1233:got NULL lanIfName or bri
dgeIfName
interface atm5.0 does not exist!
SIOCGIFFLAGS: No such device
ssk:error:15.250:rcl_wanDslLinkCfgObject:295:===> layer2 ifname is atm6
Send out CMS_MSG_CHECK_WAN_MODE event msg
ssk:error:15.264:rutPMap_addAvailableInterface:807:avail InterfaceReference Inte
rnetGatewayDevice.WANDevice.1.WANConnectionDevice.7.WANPPPConnection.1 already e
xists
ssk:error:15.287:rutLan_removeInterfaceFromBridge:1233:got NULL lanIfName or bri
dgeIfName
interface atm6.0 does not exist!
SIOCGIFFLAGS: No such device
ssk:error:15.489:rcl_wanDslLinkCfgObject:295:===> layer2 ifname is atm7
Send out CMS_MSG_CHECK_WAN_MODE event msg
ssk:error:15.503:rutPMap_addAvailableInterface:807:avail InterfaceReference Inte
rnetGatewayDevice.WANDevice.1.WANConnectionDevice.8.WANPPPConnection.1 already e
xists
ssk:error:15.528:rutLan_removeInterfaceFromBridge:1233:got NULL lanIfName or bri
dgeIfName
interface atm7.0 does not exist!
SIOCGIFFLAGS: No such device
Active defaultGateway6 =
ssk:error:15.733:rutCT_getMwbandRuleIndex:4141:Failed to open /etc/iproute2/rt_t
ables to append policy routing info
sntp:error:16.204:Have_InternetWanUp:128:Could not get lock, ret=9809
tyrone debug: After This we will not think it is first boot
GD, GD , huaqin
SO_BINDTODEVICE: No such device
tr69c:error:16.890:updateTr69cCfgInfo:1255:No DNS for mangement PVC, update upda
te status
WLmngr Daemon is running
optarg=0 shmId=0
interface wl0.0 does not exist!
ssk:error:17.570:processWatchWanConnectionMsg:1543:Enter processWatchWanConnecti
onMsg
ssk:error:17.632:processWatchWanConnectionMsg:1543:Enter processWatchWanConnecti
onMsg
ssk:error:17.637:processWatchWanConnectionMsg:1543:Enter processWatchWanConnecti
onMsg
WLMNGR-DAEMON:error:17.640:lck_checkBeforeEntry:171:lock required during cmsObj_
getNextInSubTreeFlags
WLMNGR-DAEMON:error:17.640:lck_checkBeforeEntry:171:lock required during cmsObj_
getNextInSubTreeFlags
WLMNGR-DAEMON:error:17.640:rutPMap_isWanUsedForIntfGroup:1489:could not find WAN
ifName=wl0.0
ssk:error:17.646:processWatchWanConnectionMsg:1543:Enter processWatchWanConnecti
onMsg
ssk:error:17.652:processWatchWanConnectionMsg:1543:Enter processWatchWanConnecti
onMsg
ssk:error:17.657:processWatchWanConnectionMsg:1543:Enter processWatchWanConnecti
onMsg
ssk:error:17.663:processWatchWanConnectionMsg:1543:Enter processWatchWanConnecti
onMsg
ssk:error:17.669:processWatchWanConnectionMsg:1543:Enter processWatchWanConnecti
onMsg
smd:error:17.681:interest_register:126:different match data fields for same eid
1, ignore new matchData
===> got SYSTEM_BOOT, adding eIEBoot to informEvListvconfig: socket or ioctl err
or for rem: Invalid argument
interface wl0.1.0 does not exist!
WLMNGR-DAEMON:error:17.808:lck_checkBeforeEntry:171:lock required during cmsObj_
getNextInSubTreeFlags
WLMNGR-DAEMON:error:17.808:lck_checkBeforeEntry:171:lock required during cmsObj_
getNextInSubTreeFlags
WLMNGR-DAEMON:error:17.808:rutPMap_isWanUsedForIntfGroup:1489:could not find WAN
ifName=wl0.1.0
vconfig: socket or ioctl error for rem: Invalid argument
interface wl0.2.0 does not exist!
WLMNGR-DAEMON:error:17.926:lck_checkBeforeEntry:171:lock required during cmsObj_
getNextInSubTreeFlags
WLMNGR-DAEMON:error:17.926:lck_checkBeforeEntry:171:lock required during cmsObj_
getNextInSubTreeFlags
WLMNGR-DAEMON:error:17.926:rutPMap_isWanUsedForIntfGroup:1489:could not find WAN
ifName=wl0.2.0
vconfig: socket or ioctl error for rem: Invalid argument
interface wl0.3.0 does not exist!
WLMNGR-DAEMON:error:18.042:lck_checkBeforeEntry:171:lock required during cmsObj_
getNextInSubTreeFlags
WLMNGR-DAEMON:error:18.042:lck_checkBeforeEntry:171:lock required during cmsObj_
getNextInSubTreeFlags
WLMNGR-DAEMON:error:18.042:rutPMap_isWanUsedForIntfGroup:1489:could not find WAN
ifName=wl0.3.0
vconfig: socket or ioctl error for rem: Invalid argument
wlmngr_setSsid inSsid ChinaNet-wl1
wlmngr_produceRandomSsid=ChinaNet-Ke5q
Setting SSID: "ChinaNet-6hMA"
wlmngr_setSsid inSsid ChinaNet-wl2
Setting SSID: "ChinaNet-wl2"
wlmngr_setSsid inSsid ChinaNet-wl3
Setting SSID: "ChinaNet-wl3"
wlmngr_setSsid inSsid ChinaNet-wl4
Setting SSID: "ChinaNet-wl4"
wlctl: Unsupported
chanspec 0x2b0b selected
device wl0.0 entered promiscuous mode
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
device wl0.1.0 entered promiscuous mode
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
device wl0.2.0 entered promiscuous mode
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
device wl0.3.0 entered promiscuous mode
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
wl0.0: dev_set_promiscuity(master, 1)
device wl0 entered promiscuous mode
wl0.0: add 33:33:00:00:00:01 mcast address to master interface
wl0.0: add 01:00:5e:00:00:01 mcast address to master interface
wl0.0: add 33:33:ff:c1:42:18 mcast address to master interface
br0: port 3(wl0.0) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0.0) entering forwarding state
ssk:error:24.434:ssk_main:805:cannot handle msg type 0x1000314
wl0.0: dev_set_promiscuity(master, 1)
wl0.0: add 33:33:ff:00:00:00 mcast address to master interface
BCM96328 xDSL Router 请教老大，然后怎么登录啊？root/root登录进入不了。 请问有没有HG100N TTL线刷教程
页:
[1]