我的DB120用TTL能进CFE但上不了WEB刷机还有救吗？
超级终端显示如下，呼唤高手啊：CFE version 1.0.37-102.9 for BCM96358 (32bit,SP,BE)
Build Date: Wed Jul 29 20:25:16 CST 2009 (kevin@BS5)
Copyright (C) 2000-2009 Broadcom Corporation.
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Boot Address 0xbe000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.159
Gateway IP address :
Run from flash/host (f/h)
Default host run file name : 308nfs6358
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-5) : 96358VW2
Number of MAC Addresses (1-32) : 24
Base MAC Address : 00:1e:40:53:eb:b4
PSI Size (1-64) KBytes : 24
Main Thread Number : 0
GPON Serial Number : "bazwc"
GPON Password : " "
*** Press any key to stop auto run (1 seconds) ***
Auto run second co
web info: Waiting for connection on socket 0.
CFE>
help后显示如下：
CFE> help
Available commands:
sm Set memory or registers.
dm Dump memory or registers.
w Write the whole image start from beginning of the flash
e Erase vram or ll flash except bootrom
r Run program from flash image or from host depend on fl
ag
p Print boot line and board parameter info
c Change booline parameters
f Write image to the flash
i Erase persistent storage data
b Change board parameters
reset Reset the board
flashimage Flashes a compressed image after the bootloader.
help Obtain help for CFE commands
是否用 e a 和w这两个命令刷机？刷机文件的路径如何指定呢？192.168.1.159//c:/*.bin可以吗?
把bin放在超级终端目录下尝试没有成功
CFE> w 192.168.1.159:1.bin
Loading 192.168.1.159:1.bin ...
Loading failed.: CFE error -21
*** command status = -21
放在C盘下尝试也没有成功
CFE> w 192.168.1.1:c:/1.bin
Loading 192.168.1.1:c:/1.bin ...
Loading failed.: CFE error -21
*** command status = -21 估计难，我的DB120-B1TTL设置好能进WEb都刷不了固件。 bwfj 发表于 2011-7-11 10:10 static/image/common/back.gif
估计难，我的DB120-B1TTL设置好能进WEb都刷不了固件。
为什么，WEB中的CFE刷机界面没有出来吗？ 似乎是FLASH不支持。
为什么CFE中有GPON参数这一项，以前没见过。 接到LAN4用WEN去刷啊，指定本地IP为192.168.1.100，掩码255.255.255.0，网关192.168.1.1 sniper99999 发表于 2011-7-11 16:32 static/image/common/back.gif
接到LAN4用WEN去刷啊，指定本地IP为192.168.1.100，掩码255.255.255.0，网关192.168.1.1
前面已经说了，LAN4上不了WEB，ping不通 用了e n命令后可以启动ROM，显示如下：
adsl: adsl_init entry008 00:02:48
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Jul 14 2008 00:02:46
Config Internal PHY Through MDIO
BCM63xx_ENET: Auto-negotiation timed-out
BCM63xx_ENET: 10 MB Half-Duplex (assumed)
eth0: MAC Address: 00:1E:40:53:EB:B4
Broadcom BCM6358A1 Ethernet Network Device v0.3 Jul 14 2008 00:02:46
Config Ethernet Switch Through MDIO Pseudo PHY Interface
dgasp: kerSysRegisterDyingGaspHandler: eth1 registered
eth1: MAC Address: 00:1E:40:53:EB:B5
Broadcom BCM6358A1 USB Network Device v0.4 Jul 14 2008 00:02:48
usb0: MAC Address: 00 1E 40 53 EB B6
usb0: Host MAC Address: 00 1E 40 53 EB B7
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 00:1E:40:53:EB:B8
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.120.25.0.cpe1.3
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
do_page_fault() #2: sending SIGSEGV to cfm for invalid write access to
7fff8000 (epc == 2ae89d3c, ra == 2aaffa18)
SIGSEGV
#
还是不行啊
听说用TFTP可以刷CFE,哪位达人能够指点一下吗？ CFE version 1.0.37-102.9 for BCM96358 (32bit,SP,BE)
用iptve那个口可以进web，不过en以后似乎连cfe都没有进嘛
页:
[1]
2