求救，DB120-B1刷死了，请问还有救吗？
通电后只有两个红灯，M29内存，用TTL线连接后如下信息CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: 二1月 29 07:41:15 CST 2008 (root@ZTJ)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device id 227a is not supported.
*** Board is not initialized properly ***
Press:<enter> to use current value
'-' to go previous parameter
'.' to clear the current value
'x' to exit this command
96358VW2 ------- 0
96358VW ------- 1
96358GWVG ------- 2
96358MV2G ------- 3
96358M ------- 4
96358B ------- 5
96358BGWE_OEM1 ------- 6
96359PONG ------- 7
96358SV ------- 8
96358VW2_b20 ------- 9
Board Id (0-9) :0
Number of MAC Addresses (1-32) :012
Base MAC Address :00:00:00:00:00:00
PSI Size (1-64) KBytes :24
Flash Block Size (1-128) in KBytes:064
Auxillary File System Size Percent:025
Main Thread Number :0
Flash layout changed. Need to erase all flash except bootrom
Invalid command: "e"
Available commands:
Flash Layout: Boot Kern[-1,0xbdffffff]
AuxFS[-1,0x00000000] Misc[-1,0x00000000] PSI[-1,0x00000000]
Flash RootFS Partition Length: 1107296257
100 MB Full-Duplex (auto-neg)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x805285A0 (1209760)
Initialized Data: 0x8041DD30 - 0x8041FDC0 (8336)
BSS Area: 0x8041FDC0 - 0x804265A0 (26592)
Local Heap: 0x804265A0 - 0x805265A0 (1048576)
Stack Area: 0x805265A0 - 0x805285A0 (8192)
Text (code) segment: 0x80401000 - 0x8041DD30 (118064)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Use default boot line parameters: e=192.168.1.1:ffffff00 h=192.168.1.159 g= r=h f=308nfs6358 i=bcm963xx_fs_kernel d=1 p=0
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.159
Gateway IP address :
Run from flash/host (f/h) : h
Default host run file name : 308nfs6358
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-9) :
Number of MAC Addresses (1-32) : 0
Base MAC Address : 00:00:00:00:00:00
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 0
Auxillary File System Size Percent: 0
Main Thread Number : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1
web info: Waiting for connection on socket 0.
CFE> M29的好像没留意到有什么固件，你现在应该没刷死。在cfe界面应该可以打开192.168.1.1进入升级页面。 本帖最后由 bwfj 于 2011-7-5 20:01 编辑
谢谢你的回复，可以打开192.168.1.1进入升级页面，但刷进固件重启后还是一样，猫只有两个暗红色的灯，TTL进终端到原来这个介面：
Press:<enter> to use current value
'-' to go previous parameter
'.' to clear the current value
'x' to exit this command
96358VW2 ------- 0
96358VW ------- 1
96358GWVG ------- 2
96358MV2G ------- 3
96358M ------- 4
96358B ------- 5
96358BGWE_OEM1 ------- 6
96359PONG ------- 7
96358SV ------- 8
96358VW2_b20 ------- 9
Board Id (0-9) : 说明你参数没设置对 谢谢，请问哪位大大能告诉我这款无线猫的参数DB120-B1 双USB M29内存。 要用TTL改MAC，看样子你的没改过 要用TTL改MAC，看样子你的没改过 869206429 发表于 2011-7-6 12:28 static/image/common/back.gif
要用TTL改MAC，看样子你的没改过
谢谢你的帮助， 我再试试看，还有什么地方要更改吗？ 还是不行，在CFE下运行f命令如下错误：
CFE> f
Loading 192.168.1.159:bcm963xx_fs_kernel ...
Loading failed.: CFE error -21
*** command status = -21
CFE> 没人知道吗？
页:
[1]
2