RG100A-AA刷了变砖如何办，谢谢
RG100A-AA刷了个固件后变砖现象为，能电后，LAN1到LAN4这4个全亮，然后，电源灯亮，电源灯这的同时USB灯闪一下，然后电源灯还在这，DLS灯亮，
接着回到刚才这种情况反复 都是这样
如何办？
是不是硬件坏了
ping 不通，进不了那个升级介面
如果ping time out,可以按住复位开关，然后加点试试，有没有几秒钟能PING通，如果还是ping 不通就只能用TTL线修复了 zk1013 发表于 2011-1-5 11:44 static/image/common/back.gif
如果ping time out,可以按住复位开关，然后加点试试，有没有几秒钟能PING通，如果还是ping 不通就只能用TTL ...
谢谢兄弟，再问一下，TTL线是不是2030那种手机升级数据线？ 可以用个改 zk1013 发表于 2011-1-5 12:18 static/image/common/back.gif
可以用个改
兄弟，谢谢了
1不接
2接了GND
3接了TXD
4接了RXD
用了那个linjtag，接好，设置115200，其他没有变，
猫通电没有反应
是否要JTAG? 本帖最后由 zk1013 于 2011-1-5 12:32 编辑
不需要JTAG ,接好了，打开猫的电源，然后马上打开超级终端，超级终端就会显示启动状态
zk1013 发表于 2011-1-5 12:32 static/image/common/back.gif
不需要JTAG ,接好了，打开猫的电源，然后马上打开超级终端，超级终端就会显示启动状态
一步一步接近了，呵呵，谢谢兄弟，
出现了CFE
如何办，现在 zk1013 发表于 2011-1-5 12:32 static/image/common/back.gif
不需要JTAG ,接好了，打开猫的电源，然后马上打开超级终端，超级终端就会显示启动状态
新手，无办法呀，兄弟，只好再问你了，出了CFE后如何做？ oard IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id Name : 96358VW2
Psi size in KB : 24
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:e0:fc:00:e0:fc
Ethernet PHY Type
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x8026c018
Decompression OK!
Entry at 0x8026c018
Closing network.
Starting program at 0x8026c018
Linux version 2.6.8.1 (root@localhost.localdomain) (gcc version 3.4.2) #1 Wed Ju
n 24 01:08:01 CST 2009
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
fInfo.flash_rootfs_available_length = 16252928
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 4000 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 29344k/32384k available (1908k kernel code, 2996k reserved, 503k data, 7
6k init, 0k highmem)
Calibrating delay loop... 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...unavailable.
NET: Registered protocol family 16
Total Flash size: 16384K with 128 sectors
Computing partition layout for flash of size sectors[12
Flash not used for Auxillary File System
Partition ROOTFS_KRN Blks
SubPartition Image 1 Blks[ 62: 1 ..62]
SubPartition Image 2 Blks[ 62:63 .. 124]
Blk# BlkOff Blks BlkSize AvailSize MemStart MemLen Partition Name
0 1408 1131072 131072 0xbe000580 1024 BOOTLOADER
1 012413107216252928 0xbe020000 16252928 ROOTFS_KRN
125 0 0 0 0 0xbefa0000 0 JFFS_A
125 0 1131072 131072 0xbefa0000 131072 LOG_SCRPAD
126 106496 1131072 131072 0xbefda000 24576 TW_PERSISTMEM
127 106496 1131072 131072 0xbeffa000 24576 PERSISTMEM
Can't analyze prologue code at 801eb844
SCSI subsystem initialized
usbcore: registered new driver hub
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v2.0
File system address: 0xbe7e0100
Registered device mtd dev Flash
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0050300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0052400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x3 is enabled
WIFI: Button Interrupt 0x0 is enabled
WIFI: map_external_irq begin
SES: LED GPIO 0x8018 is enabled
initLed: led: mask=0x400000, state=0
initLed: led: mask=0x0100, state=0
initLed: led: mask=0x1000000, state=0
initLed: led: mask=0x0001, state=0
initLed: led: mask=0x0004, state=0
initLed: led: mask=0x0010, state=0
initLed: led: mask=0x0002, state=0
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
u32 classifier
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Kernel panic: VFS: Unable to mount root fs on unknown-block(31,0)
<0>Rebooting in 1 seconds..
CFE version 1.0.37-6.5 for BCM96358 (32bit,SP,BE)
Build Date: Sun Apr 26 00:57:24 CST 2009 (root@MOD6538)
Copyright (C) 2000-2005 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x80528280 (1208960)
Initialized Data: 0x8041DB50 - 0x8041F980 (7728)
BSS Area: 0x8041F980 - 0x80426280 (26880)
Local Heap: 0x80426280 - 0x80526280 (1048576)
Stack Area: 0x80526280 - 0x80528280 (8192)
Text (code) segment: 0x80401000 - 0x8041DB4C (117580)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id Name : 96358VW2
Psi size in KB : 24
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:e0:fc:00:e0:fc
Ethernet PHY Type : Internal
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1
web info: Waiting for connection on socket 0.
CFE>
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x80528280 (1208960)
Initialized Data: 0x8041DB50 - 0x8041F980 (7728)
BSS Area: 0x8041F980 - 0x80426280 (26880)
Local Heap: 0x80426280 - 0x80526280 (1048576)
Stack Area: 0x80526280 - 0x80528280 (8192)
Text (code) segment: 0x80401000 - 0x8041DB4C (117580)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id Name : 96358VW2
Psi size in KB : 24
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:e0:fc:00:e0:fc
Ethernet PHY Type
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x8026c018
Decompression OK!
Entry at 0x8026c018
Closing network.
Starting program at 0x8026c018
Linux version 2.6.8.1 (root@localhost.localdomain) (gcc version 3.4.2) #1 Wed Ju
n 24 01:08:01 CST 2009
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
fInfo.flash_rootfs_available_length = 16252928
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 4000 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 29344k/32384k available (1908k kernel code, 2996k reserved, 503k data, 7
6k init, 0k highmem)
Calibrating delay loop... 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...unavailable.
NET: Registered protocol family 16
Total Flash size: 16384K with 128 sectors
Computing partition layout for flash of size sectors[12
Flash not used for Auxillary File System
Partition ROOTFS_KRN Blks
SubPartition Image 1 Blks[ 62: 1 ..62]
SubPartition Image 2 Blks[ 62:63 .. 124]
Blk# BlkOff Blks BlkSize AvailSize MemStart MemLen Partition Name
0 1408 1131072 131072 0xbe000580 1024 BOOTLOADER
1 012413107216252928 0xbe020000 16252928 ROOTFS_KRN
125 0 0 0 0 0xbefa0000 0 JFFS_A
125 0 1131072 131072 0xbefa0000 131072 LOG_SCRPAD
126 106496 1131072 131072 0xbefda000 24576 TW_PERSISTMEM
127 106496 1131072 131072 0xbeffa000 24576 PERSISTMEM
Can't analyze prologue code at 801eb844
SCSI subsystem initialized
usbcore: registered new driver hub
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v2.0
File system address: 0xbe7e0100
Registered device mtd dev Flash
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0050300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0052400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x3 is enabled
WIFI: Button Interrupt 0x0 is enabled
WIFI: map_external_irq begin
SES: LED GPIO 0x8018 is enabled
initLed: led: mask=0x400000, state=0
initLed: led: mask=0x0100, state=0
initLed: led: mask=0x1000000, state=0
initLed: led: mask=0x0001, state=0
initLed: led: mask=0x0004, state=0
initLed: led: mask=0x0010, state=0
initLed: led: mask=0x0002, state=0
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
u32 classifier
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Kernel panic: VFS: Unable to mount root fs on unknown-block(31,0)
<0>Rebooting in 1 seconds..
CFE version 1.0.37-6.5 for BCM96358 (32bit,SP,BE)
Build Date: Sun Apr 26 00:57:24 CST 2009 (root@MOD6538)
Copyright (C) 2000-2005 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x80528280 (1208960)
Initialized Data: 0x8041DB50 - 0x8041F980 (7728)
BSS Area: 0x8041F980 - 0x80426280 (26880)
Local Heap: 0x80426280 - 0x80526280 (1048576)
Stack Area: 0x80526280 - 0x80528280 (8192)
Text (code) segment: 0x80401000 - 0x8041DB4C (117580)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id Name : 96358VW2
Psi size in KB : 24
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:e0:fc:00:e0:fc
Ethernet PHY Type : Internal
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1
web info: Waiting for connection on socket 0.
CFE> 本帖最后由 zk1013 于 2011-1-5 13:11 编辑
你加我QQ吧 75889835,这里也有教程https://www.chinadsl.net/thread-24950-1-1.html
页:
[1]
2