DB120双USB口的刷了两个版本都成功刷电信原版挂了
公版3.10L 成功v3.1-cfe-128kv3.1-128k都成功刷 bcm96358img-ct.w 挂了IP设为192.168.1.88 先按住猫的RST键,然后打开电源（不能松开RST），继续按住20秒钟(DB120红色电源灯常亮）。然后松开RST键LAN4口 刷现在已经没反应 123有反应.电源灯跟INTERNET微亮
CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: 2008-05-27 16:57:32 2 (tashin@linux-server1)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
*** Board is not initialized properly ***
Press:<enter> to use current value
'-' to go previous parameter
'.' to clear the current value
'x' to exit this command
96358VW2 ------- 0
96358VW ------- 1
96358GWVG ------- 2
96358MV2G ------- 3
96358M ------- 4
96358B ------- 5
96358BGWE_OEM1 ------- 6
96359PONG ------- 7
96358SV ------- 8
Board Id (0-8) :0
希望高手 指点救活我的 大亚 以后不敢在刷了！谢谢！热心的高手可加我QQ：594888005
用TTL 线把相关参数仔细设置遍就没事了吧。你现在停在选Board Id 的地方，没TTL线建议不要弄，必竟不用TTL线能完全在WEB 能安全刷的固件很少 Redcock 发表于 2010-10-30 10:20 static/image/common/back.gif
用TTL 线把相关参数仔细设置遍就没事了吧。你现在停在选Board Id 的地方，没TTL线建议不要弄，必竟不用TTL线 ...
呵呵！好了原来是犯了低级的错误啊！哈哈(shengli: 刷好后的终端显示是这样的一切正常 用的是 bcm96358img-ct.w 的CFE
Linux version 2.6.8.1 (tashin@linux-server1) (gcc version 3.4.2) #1 Mon Jul 21 1
0:26:46 CST 2008
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 4000 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 29292k/32384k available (1951k kernel code, 3048k reserved, 508k data, 8
0k init, 0k highmem)
Calibrating delay loop... 299.00 B
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...unavailable.
NET: Registered protocol family 16
Computing partition layout for flash of size sectors
Flash split 25% into RootFS+Kernel : AuxFS
Partition ROOTFS_KRN Blks[ 92: 1 ..92]
SubPartition Image 1 Blks[ 46: 1 ..46]
SubPartition Image 2 Blks[ 46:47 ..92]
Blk# BlkOff Blks BlkSize AvailSize Me
0 1408 1131072 131072 0xbe000580 1024 BOOTLOADER
1 0 9213107212058624 0xbe020000 12058624 ROOTFS_KRN
93 0 32131072 4194304 0xbeba0000 4194304 JFFS_AUXFS
125 0 1131072 131072 0xbefa0000 131072 LOG_SCRPAD
126 106496 1131072 131072 0xbefda000 24576 MISC_DATAS
127 106496 1131072 131072 0xbeffa000 24576 PERSISTMEM
Can't analyze prologue code at 801f66a4
SCSI subsystem initialized
usbcore: registered new driver hub
TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca)
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v2.0
File system address: 0xbe020100
Registered device mtd dev Flash
Registered device mtd dev Flash
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0050300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 ->
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0052400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered n
SES: Button Interrupt 0x0 is enabled
SES: LED GPIO 0x8021 is enabled
WIFI: Button Interrupt 0x3 is enabled
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
Mirror/redirect action on
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 80k freed
init started:BusyBox v1.00 (2008.07.21-02:31+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
BusyBox v1.00 (2008.07.21-02:31+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Jul 21 2008 10:24:02
Config Internal PHY Through MDIO
BCM63xx_ENET: Auto-negotiation timed-out
BCM63xx_ENET: 10 MB Half-Duplex (assumed)
eth0: MAC Address: 02:18:26:20:0B:01
Broadcom BCM6358A1 Ethernet Network Device v0.3 Jul 21 2008 10:24:02
Config Ethernet Switch Through MDIO Pseudo PHY Interface
dgasp: kerSysRegisterDyingGaspHandler: eth1 registered
eth1: MAC Address: 02:18:26:20:0B:02
Broadcom BCM6358A1 USB Network Device v0.4 Jul 21 2008 10:24:05
usb0: MAC Address: 02 18 26 20 0B 03
usb0: Host MAC Address: 02 18 26 20 0B 04
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system po
wl0: MAC Address: 02:18:26:20:0B:05
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.150.10.15.cpe2.2
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
eth1 Link UP.
configure file is not available, use factory settings.
XML configuration parsed successfully: error none.
XML configuration parsed successfully: error none.
BcmAdsl_Initialize=0xC00BA3F8, g_pFnNotifyCallback=0xC00D33C4
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
pSdramPHY=0xA1FFFFF8, 0xFFFFFFFF 0xFFFFFFFF
AdslCoreHwReset: AdslOemDataAddr = 0xA1FFD3D4
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
ATM proc init !!!
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (253 buckets, 0 max) - 376 bytes per conntrack
==> Bcm963xx Software Version: V3.10-COGO V2.4.B1210. <==
device usb0 entered promiscuous mode
br0: port 1(usb0) entering learning state
br0: topology change detected, propagating
br0: port 1(usb0) entering forwar
device eth0 entered promiscuous mode
br0: port 2(eth0) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0) entering forwarding state
Setting SSID "CTC-E8"
Setting country code using abbreviation: "ALL"
wlctl: Not down
wlctl: Not Found
wlctl: Not Found
wlctl: Not Found
wlctl: Unsupported
wlctl: Bad Channel
wl0: current channel 1
device wl0 entered promiscuous mode
br0: port 3(wl0) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0) entering forwarding
eth1.2: MAC Address: 02:18:26:20:0B:02
eth1.3: MAC Address: 02:18:26:20:0B:02
eth1.4: MAC Address: 02:18:26:20:0B:02
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
device usb0 left promiscuous mode
br0: port 1(usb0) entering disabled state
device eth0 left promiscuous mode
br0: port 2(eth0) entering disabled state
device wl0 left promiscuous mode
br0: port 3(wl0) entering disabled state
device usb0 entered promiscuous mode
br0: port 1(usb0) entering learning state
br0: topology change detected, propagating
br0: port 1(usb0) entering forwarding state
device eth0 entered promiscuous mode
br0: port 2(eth0) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0) entering forwarding state
device wl0 entered promiscuous mode
br0: port 3(wl0) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0) entering forwarding state
device eth1.2 entered promiscuous mode
br0: port 4(eth1.2) entering learning state
br0: topology change detected, propagating
br0: port 4(eth1.2) entering forwarding state
device eth1.3 entered promiscuous mode
br0: port 5(eth1.3) entering learning state
br0: topology change detected, propagating
br0: port 5(eth1.3) entering forwarding state
device eth1.4 entered promiscuous mode
br0: port 6(eth1.4) entering learning state
br0: topology change detected, propagating
br0: port 6(eth1.4) entering forwarding state
insmod: cannot insert `/lib/modules/2.6.8.1/extra/vnet.ko': Success (17): Succes
s
device usb0 left promiscuous mode
br0: port 1(usb0) entering disabled state
device eth0 left promiscuous mode
br0: port 2(eth0) entering disabled state
device wl0 left promiscuous mode
br0: port 3(wl0) entering disabled state
device eth1.2 left promiscuous mode
br0: port 4(eth1.2) entering disabled state
device eth1.3 left promiscuous mode
br0: port 5(eth1.3) entering disabled state
device eth1.4 left promiscuous mode
br0: port 6(eth1.4) entering disabled state
device usb0 entered promiscuous mode
br0: port 1(usb0) entering learning state
br0: topology change detected, propagating
br0: port 1(usb0) entering forwarding state
device eth0 entered promiscuous mode
br0: port 2(eth0) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0) entering forwarding state
device wl0 entered promiscuous mode
br0: port 3(wl0) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0) entering forwarding state
device eth1.2 entered promiscuous mode
br0: port 4(eth1.2) entering learning state
br0: topology change detected, propagating
br0: port 4(eth1.2) entering forwarding state
device eth1.3 entered promiscuous mode
br0: port 5(eth1.3) entering learning state
br0: topology change detected, propagating
br0: port 5(eth1.3) entering forwarding state
device eth1.4 entered promiscuous mode
br0: port 6(eth1.4) entering learning state
br0: topology change detected, propagating
br0: port 6(eth1.4) entering forwarding state
*****************************************
Wi-Fi Simple Config Application - Intel Corp.
Version: Build 1.0.5, November 19 2006
*********************************************
Created @ May8 2008 22:11:50
Initializing stack...button monitor start...!
OK
Now starting stack
get mac = 02 18 26 20 0B 05
sntp: host not found
Scratch pad is not initialized.
Scratch pad is not initialized.
No scratch pad found.Initialize scratch pad...
******* MODE: AP with built-in Registrar and UPnP Proxy *******wsc_del_ie: no va
lid ie was saved, len = -1
wsc_del_ie: no valid ie was saved, len = -1
WSC: Build-in Registrar, wait for start command....
Erasing 128 Kibyte @ 3e0000 -- 96 % complete.
CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: 2008-05-27 16:57:32 2 (tashin@linux-server1)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x80528450 (1209424)
Initialized Data: 0x8041DEB0 - 0x8041FC60 (7600)
BSS Area: 0x8041FC60 - 0x80426450 (26608)
Local Heap: 0x80426450 - 0x80526450 (1048576)
Stack Area: 0x80526450 - 0x80528450 (8192)
Text (code) segment: 0x80401000 - 0x8041DEA8 (118440)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-8) : 96358VW2
Number of MAC Addresses (1-32) : 11
Base MAC Address : 02:18:26:20:0b:01
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xbe020000) ...
Code Address: 0x80010000, Entry Address: 0x80278018
Decompression OK!
Entry at 0x80278018
Closing network.
Starting program at 0x80278018
Linux version 2.6.8.1 (tashin@linux-server1) (gcc version 3.4.2) #1 Mon Jul 21 1
0:26:46 CST 2008
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 4000 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer.(32bit,SP,BE)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)shin@linux-server1)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Boot Address 0
Memory: 29292k/32384k available (1951k kernel code, 3048k reserved, 508k data, 88-A, id 0x2201, size 16384KB
0k init, 0k highmem)
CPU type 0x2A010:
Calibrating delay loop... 299.00 BogoMIPS
C
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)(32MB)
Total memory us
Checking for 'wait' instruction...unavailable.
NET: Registered protocol family 16 0x8041DEB0 - 0x8041FC60 (7600)
Computing partition layout for flash of size sectors 0x8041FC60 -
SubPartition Image 2 Blks[ 46:47 ..92]cation Factor: I:00000000 - D:00000000
Blk# BlkOff Blks BlkSize AvailSize MemStart MemLen Partition Name68.1.1:ffffff00
0 1408 1131072 131072 0xbe000580 1024 BOOTLOADER
Gateway IP address :
1 0 9213107212058624 0xbe020000 12058624 ROOTFS_KRN: h
Default host run file name
93 0 32131072 4194304 0xbeba0
PSI Size (1-64) KBytes
SCSI subsystem initialized
Fl
usbcore: registered new driver hub28
TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca)
Main Thread Number : 1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.op auto run (1 seconds) ***
Initializing Cryptographic API
Auto run second count down: 0
PPP generic driver version 2.4.2SWD:********
web
NET: Registered protocol family
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
CFE version 1.0.37-10.3 for B
ehci_hcd 0000:00:0a.0: EHCI Host Controller
Build Date: 200
PCI: Setting latency timer of device 0000:00:0a.0 to 64
Copyright (C)
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0050300
Boot Address 0xb
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1MT|S29GL128-A, id 0x2201, size 16384KB
ohci_hcd: block sizes: ed 64 td 64ap: 0x80426450 - 0x
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
Stack Area:
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64DEA8 (118440)
ohci_hcd 0000:00:09.0: irq 13, pci mem c00524000529000 - 0x00569000
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblpkernel d=1 p=0
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driverfffff00
H
Initializing USB Mass Storage driver...68.1.100
usbcore: registered new driver usb-storage :
USB Mass Storage support registered.: f
usbcore: registered new driver usbnet : vmlinux
SES: Button Interrupt 0x0 is enabled file name : bcm963xx_fs_kernel
SES: LED GPIO 0x8021 is enabled
Boot del
WIFI: Button Interrupt 0x3 is enabled
Board Id
Serial: BCM63XX driver $
NET: Registered protocol family 2(1-128) in KBytes: 128
IP: routing cache hash table of 512 buckets, 4Kbytesze Percent: 25
TCP: Hash tables configured (established 2048 bind 4096)
*** Press any key to stop auto run (
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 80k freed
init started:BusyBox v1.00 (2008.07.21-02:31+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
BusyBox v1.00 (2008.07.21-02:31+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Jul 21 2008 10:24:02
Config Internal PHY Through MDIO
页:
[1]