这个猫支持WIFI？
回复 6# hotqj
我的启动过程如下：
Booting
Press 'ESC' to enter BOOT console...
Using Int. PHY
0xB8003330=0x0
0xB800332C=0x0
0xB8001000=0xc0000000
0xB8003308=0x2f35500
Listening Multicast upgrade packets....0
Decompress first file... image check addr:0xbd011000 len 5398528
ok!
Linux version 2.6.21.5 (chenhui@build.huawei.com) (gcc version 3.4.6-1.3.6) #66
Fri Jul 9 11:01:26 CST 2010
CPU revision is: 0000ff00
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Built 1 zonelists.Total pages: 8128
Kernel command line: console=ttyS0, 115200 mem=32Mroot=31:2
Primary instruction cache 16kB, linesize 16 bytes.
Primary data cache 8kB, linesize 16 bytes.
Synthesized TLB refill handler (17 instructions).
Synthesized TLB load handler fastpath (31 instructions).
Synthesized TLB store handler fastpath (31 instructions).
Synthesized TLB modify handler fastpath (25 instructions).
PID hash table entries: 128 (order: 7, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 24136k/32768k available (3776k kernel code, 8632k reserved, 832k data, 1
24k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction...disabled.
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Sangoma WANPIPE Router v1.1 (c) 1995-2000 Sangoma Technologies Inc.
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 128 (order: -3, 512 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
<<<<<<<disable GPIO JTAG function.
request_irq for GPIO_ABCD_IRQ 10 success
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
fuse init (API version 7.8)
JFFS2 version 2.2. (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered (default)
Serial: 8250/16550 driver $Revision: 1.1.2.3 $ 1 ports, IRQ sharing disabled
netlog start
serial8250: ttyS0 at MMIO 0x0 (irq = 12) is a 16550A
PPP generic driver version 2.4.2
NET: Registered protocol family 24
IMQ starting with 3 devices...
IMQ driver loaded successfully.
Hooking IMQ before NAT on PREROUTING.
Hooking IMQ after NAT on POSTROUTING.
flash device: 0x1000000 at 0xbd000000
get SPI chip driver!
Physically mapped flash: Found an alies 0x1000000 for the chip at 0x0, mxic devi
ce detect.
Creating 6 MTD partitions on "Physically mapped flash":
0x00000000-0x00010000 : "boot"
0x00010000-0x00011000 : "flag"
0x00011000-0x00791000 : "main"
0x00791000-0x00880000 : "config"
0x00880000-0x00c80000 : "middle"
0x00c80000-0x01000000 : "slave"
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for option1
usbcore: registered new interface driver option
drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.1
bhal: bhal_init entry
Mars .....UsbProbeFlag ==0.
Led_module_init ok<6>REALTEK NIC Ethernet driver v0.1 (Feb 13, 2009)
eth0: RTL-8139C+ at 0xb8018000, 4c:54:99:b3:2b:d0, IRQ 26
RTL8672 NIC100 Probing..
eth phy patch done!
Enable 8671G 1 function
Enable 8671 0 function
Enable 8672 function
initFreeRxSkbList
initFreeRxSkbList free_rx_skb_producer=48
ratm: Realtek SAR v1.02 (Feb 17, 2009)
RTL8192C/RTL8188C driver version 0.2 (2010-03-31/2010-05-11)
=====>>INSIDE rtl8192cd_init_one <<=====
Clock source is 35.328MHz
vendor_deivce_id=819110ec
_
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
dev[<NULL>]:wapiType UCastKeyType psk[] len
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
dev[<NULL>]:wapiType UCastKeyType psk[] len
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
dev[<NULL>]:wapiType UCastKeyType psk[] len
=====>>EXIT rtl8192cd_init_one <<=====
disable USB phy 0
dwc_otg: version 2.60a 22-NOV-2006
----init hcd-----
DWC_otg: Using DMA mode
DWC_otg: address of dwc_otg_hcd->xacterr_cnt: 0x811b098c
dwc_otg lm0: DWC OTG Controller
dwc_otg lm0: new USB bus registered, assigned bus number 1
dwc_otg lm0: irq 11, io mem 0xb8030000
DWC_otg: Init: Port Power? op_state=1
DWC_otg: Init: Power Port (0)
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
GACT probability on
Mirror/redirect action on
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (256 buckets, 2048 max)
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
6WIND/LSIIT IPv6 multicast forwarding 0.1 plus PIM-SM/SSM with *BSD API
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 124k freed
init started: BusyBox v1.9.1 (2010-07-09 11:02:19 CST)
starting pid 119, tty '': '/etc/init.d/rcS'
rcs
RCS DONE
starting pid 122, tty '': '/bin/sh'
BusyBox v1.9.1 (2010-07-09 11:02:19 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
mknod: /dev/boardled: File exists
Loading drivers and kernel modules...
-----mc is cut-----
enter the msg
===enter the log
Waiting for cli start!-CWMP app version: V100R002C05B022SP01 cwmp app V1.2.3.0.0
CWMP stk version: V100R002C05B022SP01 cwmp stk V1.2.3.0.0
|TSP_DBGetPara ok ulPort = 23
-ConfigDefaultSsl return: 0
|============Start vendor config deal.============
-not support, pacStandUse
AdslGetCfgFromDB read DB error, use default value.
\
FILE: midmsg.c, LINE: 637
leaveMid_MsgReg
InitAdslMode....
InitAdsl
Welcome Visiting HuaweiHome Gateway
Copyright by Huawei Technologies Co., Ltd.
Login:
RTL: Adsl DOWN.
FILE: midmsg.c, LINE: 703
RTL: Adsl DOWN.
Tr069Enableis(1)
FILE: midmsg.c, LINE: 749
nowI don't initmidcom, just boot tr069
RTL: Adsl DOWN.
pin_string= PIN=0
accum=0
pin_string= PIN=0
accum=0
device wl0 is not a slave of br0
device wl0.1 is not a slave of br0
device wl0.2 is not a slave of br0
device wl0.3 is not a slave of br0
arp uses obsolete (PF_INET,SOCK_PACKET)
vlan enabled!
device eth0 is not a slave of br0
device eth0.2 entered promiscuous mode
device eth0.3 entered promiscuous mode
device eth0.4 entered promiscuous mode
device eth0.5 entered promiscuous mode
eth0.2: Promiscuous mode enabled.
eth0.2: Promiscuous mode enabled.
br0: port 1(eth0.2) entering learning state
eth0.2: Promiscuous mode enabled.
br0: topology change detected, propagating
br0: port 1(eth0.2) entering forwarding state
eth0.3: Promiscuous mode enabled.
eth0.3: Promiscuous mode enabled.
br0: port 2(eth0.3) entering learning state
eth0.3: Promiscuous mode enabled.
br0: topology change detected, propagating
br0: port 2(eth0.3) entering forwarding state
eth0.4: Promiscuous mode enabled.
eth0.4: Promiscuous mode enabled.
br0: port 3(eth0.4) entering learning state
eth0.4: Promiscuous mode enabled.
br0: topology change detected, propagating
br0: port 3(eth0.4) entering forwarding state
eth0.5: Promiscuous mode enabled.
eth0.5: Promiscuous mode enabled.
br0: port 4(eth0.5) entering learning state
eth0.5: Promiscuous mode enabled.
br0: topology change detected, propagating
br0: port 4(eth0.5) entering forwarding state
device eth0 is not a slave of br0
WanIpv6NotifyLan ...
ratm(itf 0): open 8.46
create: ch0 (8/46) 7679,0
sar_set_atm_data_mode
initFreeRxSkbList
initFreeRxSkbList free_rx_skb_producer=48
Enable 8671G 1 function
Enable 8671 0 function
Enable 8672 function
create: ch0 (8/46) 7679,0
applying workaround...done
V100R002C03 DHCP Client V3.01
killall: tr064: no process killed
Read upnp enable return: 0.
ratm(itf 0): open 0.35
create: ch1 (0/35) 7679,0
sar_set_atm_data_mode
initFreeRxSkbList
initFreeRxSkbList free_rx_skb_producer=48
Enable 8671G 1 function
Enable 8671 0 function
Enable 8672 function
create: ch0 (8/46) 7679,0
create: ch1 (0/35) 7679,0
applying workaround...done
device nas_0_35_1 entered promiscuous mode
br0: port 5(nas_0_35_1) entering learning state
br0: topology change detected, propagating
br0: port 5(nas_0_35_1) entering forwarding state
killall: tr064: no process killed
Read upnp enable return: 0.
ratm(itf 0): open 0.100
create: ch2 (0/100) 7679,0
sar_set_atm_data_mode
initFreeRxSkbList
initFreeRxSkbList free_rx_skb_producer=48
Enable 8671G 1 function
Enable 8671 0 function
Enable 8672 function
create: ch0 (8/46) 7679,0
create: ch1 (0/35) 7679,0
create: ch2 (0/100) 7679,0
applying workaround...done
device nas_0_100_1 entered promiscuous mode
br0: port 6(nas_0_100_1) entering learning state
br0: topology change detected, propagating
br0: port 6(nas_0_100_1) entering forwarding state
killall: tr064: no process killed
Read upnp enable return: 0.
ratm(itf 0): open 0.127
create: ch3 (0/127) 7679,0
sar_set_atm_data_mode
initFreeRxSkbList
initFreeRxSkbList free_rx_skb_producer=48
Enable 8671G 1 function
Enable 8671 0 function
Enable 8672 function
create: ch0 (8/46) 7679,0
create: ch1 (0/35) 7679,0
create: ch2 (0/100) 7679,0
create: ch3 (0/127) 7679,0
applying workaround...done
device nas_0_127_1 entered promiscuous mode
br0: port 7(nas_0_127_1) entering learning state
br0: topology change detected, propagating
br0: port 7(nas_0_127_1) entering forwarding state
killall: tr064: no process killed
Read upnp enable return: 0.
ratm(itf 0): open 8.35
create: ch4 (8/35) 7679,0
sar_set_atm_data_mode
initFreeRxSkbList
initFreeRxSkbList free_rx_skb_producer=48
Enable 8671G 1 function
Enable 8671 0 function
Enable 8672 function
create: ch0 (8/46) 7679,0
create: ch1 (0/35) 7679,0
create: ch2 (0/100) 7679,0
create: ch3 (0/127) 7679,0
create: ch4 (8/35) 7679,0
applying workaround...done
device nas_8_35_1 entered promiscuous mode
br0: port 8(nas_8_35_1) entering learning state
br0: topology change detected, propagating
br0: port 8(nas_8_35_1) entering forwarding state
killall: tr064: no process killed
Read upnp enable return: 0.
ratm(itf 0): open 8.85
create: ch5 (8/85) 7679,0
sar_set_atm_data_mode
initFreeRxSkbList
initFreeRxSkbList free_rx_skb_producer=48
Enable 8671G 1 function
Enable 8671 0 function
Enable 8672 function
create: ch0 (8/46) 7679,0
create: ch1 (0/35) 7679,0
create: ch2 (0/100) 7679,0
create: ch3 (0/127) 7679,0
create: ch4 (8/35) 7679,0
create: ch5 (8/85) 7679,0
applying workaround...done
device nas_8_85_1 entered promiscuous mode
br0: port 9(nas_8_85_1) entering learning state
br0: topology change detected, propagating
br0: port 9(nas_8_85_1) entering forwarding state
IPv6 bind flag ucIPv6BindEbl: 1
port_no -1 not surported, br:br0, port:wl0.1
port_no -1 not surported, br:br0, port:wl0.1
IPv6 bind flag ucIPv6BindEbl: 1
killall: tr064: no process killed
Read upnp enable return: 0.
atp: not support krnl version:, default:
insmod: can't open '/lib/kernel/net/netfilter/nf_conntrack_gre.ko': No such file
or directory
insmod: can't open '/lib/kernel/net/ipv4/netfilter/nf_nat_gre.ko': No such file
or directory
port0 is link up
RTNETLINK answers: No such file or directory
Action 4 device imq0 ifindex 2
RTNETLINK answers: No such file or directory
Action 4 device imq0 ifindex 2
RTNETLINK answers: No such file or directory
Action 4 device imq0 ifindex 2
RTNETLINK answers: No such file or directory
Action 4 device imq0 ifindex 2
RTNETLINK answers: No such file or directory
Action 4 device imq0 ifindex 2
RTNETLINK answers: No such file or directory
Action 4 device imq0 ifindex 2
get zone error
timezone=Beijing
---->Sntp doesn't enable!
Daemon: 1063
close atm port mirror!
ATP_IPV6_Init!now, changed the ipv6 enable status to: 0killall: tr064: no proce
ss killed
Read upnp enable return: 0.
Get invalid input parameter, str :, strlen : 0 !FILE LINE
ATP_IPV6COMMON_CheckIPv6Addressmeet error .FILE LINE
FILE:dlnacms.c, LINE:122, MODULE:DLNA>DLNA enable:0
FILE:dlnacms.c, LINE:129, MODULE:DLNA>DLNA detectpath:
FILE:dlnacms.c, LINE:386, MODULE:DLNA> ATP_DLNA_Stop()!
killall: dms: no process killed
killall: scanner: no process killed
DLNA INIT OK............
===bUsbconf=0====!
<5>eth0.2: Promiscuous mode enabled.
eth0.3: Promiscuous mode enabled.
br0: port 2(eth0.3) entering disabled state
eth0.4: Promiscuous mode enabled.
br0: port 3(eth0.4) entering disabled state
eth0.5: Promiscuous mode enabled.
br0: port 4(eth0.5) entering disabled state
!!Huawei
Password:
ATP>start
^
ATP>
到此，无法继续了。大虾教我！！！
楼上请问，这个连接的端口速率是多少，我的连接不上是乱码
回复 12# RachiePhong
你使用sh命令试试看。
回复 14# hotqj
谢谢版主！
目前情况如下：
Login incorrect!
Login:!!Huawei
Password:
ATP>sh
BusyBox v1.9.1 (2010-07-09 11:02:19 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
# ls
bin etc lib man proc tmp var
dev init linuxrcmnt sbin usr
# cd var
# ls
cache fs locks radvd vport_result
curcfg.xml ftp log run wan
dhcp fuse log.cfg state wlan_start.lck
dms group mldproxy tempconf.xml zebra
dns igmp passwd tmp
etc lan prsite.conf usb
# cd /
# cd bin
# ls
adslcmd date gzip mini_upnpd ps tr064
adslctrl dbase ifdns mkdir pwd traceroute6
ash ddnsc igmpproxy mknod radvd true
ated df ip mldproxy radvdump umount
atmcmd dhcp6c ip6tables monitor ripd upg
bftpd dhcp6s ipcheck mount rm usbmount
brctl dhcpc iptables mpoad scanner web
busybox dhcpr iwconfig msg sh wlancmd
cat dhcps iwcontrol mv siproxd wscd
chmod dms iwpriv netlogger sleep zcat
chown dns kill netstat sntp zebra
cli ebtables klog ntfs-3g sshd
cms echo ln ping startbsp
console equipcmd log ping6 swapdev
cp ethcmd ls pppc sync
cwmp gunzip midcom ppps tc
# cd /
#
已经找到 curcfg.xml 文件，但是没有 vi 命令可用！还请大虾不吝赐教！！谢谢先！！！
回复 13# xtony123
115200
没看到有JTAG接口
回复 15# RachiePhong
可以试试在终端下使用tftp命令试试看。。。
因为这是一个我从来没有接触过的硬件方案。所以只能一步一步的来试试看了。
这东西貌似不错！
我们这好久才有这样的猫哦！