线路板右侧WPS和Wlan按钮之间的是插线座是不是RS232接口？如果是的，是不是可以用TTL线获得管理员密码？
tonychan 发表于 2010-9-14 22:46 https://www.chinadsl.net/images/common/back.gif
那个4针的应该就是TTL。
TTL的接口定义可以参考HG522的，看样子象是一样的接口定义。
那个4针的应该就是TTL。
antitel 发表于 2010-9-15 11:18 https://www.chinadsl.net/images/common/back.gif
关键是怎么破解啊？？
重庆要好久才能EPON哟~~
U-Boot 1.1.3 (Aug3 2010 - 23:11:02)
Board: Ralink APSoC DRAM:32 MB
relocate_code Pointer at: 81fb0000
config usb..
The Flash ID =0000227E
flash_protect ON: from 0xBF000000 to 0xBF01D3FF
protect on 0
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 3.3
--------------------------------------------
ASIC 3052_MP2 (Port5<->None)
DRAM component: 128 Mbits
DRAM bus: 32 bit
Total memory: 32 MBytes
Flash component: NOR Flash
Date:Aug3 2010Time:23:11:02
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
##### The CPU freq = 384 MHZ ####
SDRAM bus set to 32 bit
SDRAM size =32 Mbytes
@Start First PHY modio study cmd.
eth_register
Eth0 (10/100-M)
enetvar=ethaddr,Eth addr:00:AA:BB:CC:DD:10
00:AA:BB:CC:DD:10:
eth_current->name = Eth0 (10/100-M)
netboot_common, argc= 2
*************buf = 0x81fcd5a0
**********NexTxPacket = 81fe4640
NetTxPacket = 0x81FE4640
NetRxPackets = 0x81FE4C40
NetRxPackets = 0x81FE5240
NetRxPackets = 0x81FE5840
NetRxPackets = 0x81FE5E40
NetRxPackets = 0x81FE6440
NetRxPackets = 0x81FE6A40
NetRxPackets = 0x81FE7040
NetRxPackets = 0x81FE7640
NetRxPackets = 0x81FE7C40
NetRxPackets = 0x81FE8240
NetRxPackets = 0x81FE8840
NetRxPackets = 0x81FE8E40
NetRxPackets = 0x81FE9440
NetRxPackets = 0x81FE9A40
NetRxPackets = 0x81FEA040
NetRxPackets = 0x81FEA640
NetRxPackets = 0x81FEAC40
NetRxPackets = 0x81FEB240
NetRxPackets = 0x81FEB840
NetRxPackets = 0x81FEBE40
KSEG1ADDR(NetTxPacket) = 0xA1FE4640
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
Header Payload scatter function is Disable !!
ETH_STATE_ACTIVE!!
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
You choosed 4
eth_register
Eth0 (10/100-M)
enetvar=ethaddr,Eth addr:00:AA:BB:CC:DD:10
00:AA:BB:CC:DD:10:
eth_current->name = Eth0 (10/100-M)
4: System Enter Boot Command Line Interface.
U-Boot 1.1.3 (Aug3 2010 - 23:11:02)
main_loop !!
RT3052 # help
help
loopback - Ralink eth loopback test !!
? - alias for 'help'
bootm - boot application image from memory
bootp - boot image via network using BootP/TFTP protocol
cp - memory copy
echo - echo args to console
erase - erase FLASH memory
help - print online help
md - memory display
mdio - Ralink PHY register R/W command !!
mm - memory modify (auto-incrementing)
mw - memory write (fill)
nm - memory modify (constant address)
printenv- print environment variables
protect - enable or disable FLASH write protection
setenv- set environment variables
tftpboot- boot image via network using TFTP protocol
uip - uip command
version - print monitor version
RT3052 #
请教，下一步用哪个命令，我LINUX 九窍通了八窍。 谢谢
回复 2# -h-
这个机器wan口是千兆，lan口是百兆，我还在想华为是不是设计错了，要是lan用千兆多好啊！是不是其他故障？
这个不可能一拿过来就让你改的 电信那里还要做数据
今天刚刚装 还在使用 感觉还可以
不知道里面是PPPOE拨号还是别的什么设置 反正不是以前的账号了 电信这招蛮毒想看看里面到底怎么回事 电信给我个新的账号 我去查密码竟然查不到的 连要换个路由器都不行 彻底绑定希望破解
这个不可能一拿过来就让你改的 电信那里还要做数据
今天刚刚装 还在使用 感觉还可以
不知道里面是PPPOE拨 ...
xiaogg 发表于 2010-9-27 22:08 https://www.chinadsl.net/images/common/back.gif
换了新帐号后,密码应该是和老帐号的密码一样的(据电信的人这么说),不过我也遇到了同样的问题, 好在可以打10000号,要求reset成初始密码,并告诉你.之后就能在网上自己改了
hg255d里面internet连接应该也是pppoe, 我的还没来得及把玩就被电信拿了回去,换成了烽火的hg330,