csssmx 发表于 2010-5-13 19:33:12

rg100a用JTAG刷机，显示如下，有没有问题？

Microsoft Windows XP [版本 5.1.2600](C) 版权所有 1985-2001 Microsoft Corp. C:\Documents and Settings\Administrator>cd.. C:\Documents and Settings>cd.. C:\>cd 1 C:\1>cd jtag C:\1\JTAG>brjtag -probeonly /erasechip ==============================================
Broadcom EJTAG Debrick Utility v1.5-hugebird============================================== Probing bus ... Done Instruction Length set to 5 CPU running under BIG endian CPU Chip ID: 00000110001101011000000101111111 (0635817F)*** Found a Broadcom BCM6358 Rev 1 CPU chip ***
- EJTAG IMPCODE ....... : 00000000100000011000100100000100 (00818904)
- EJTAG Version ....... : 1 or 2.0
- EJTAG DMA Support ... : Yes
- EJTAG Implementation flags: R4k MIPS16 MIPS32 Issuing Processor / Peripheral Reset ... DoneEnabling Memory Writes ... DoneHalting Processor ... <Processor did NOT enter Debug Mode!> ... DoneClearing Watchdog ... DoneInitialize EBI ... Skipped Probing Flash at (Probe Address: 0x1fc00000) ...
Match Flash Chip (VenID:DevID = 017e : 2101)*** Found a Spansion S29GL128N/P Uni
(16MB) Flash Chip ***
- Flash Chip Window Start .... : 1f000000
- Flash Chip Window Length ... : 01000000
- Selected Area Start ........ : 00000000
- Selected Area Length ....... : 00000000 Flash Sector Protection type 1 Erase whole chip ...
Done!
*** REQUESTED OPERATION IS COMPLETE *** C:\1\JTAG>brjtag -flash:cfe ==============================================
Broadcom EJTAG Debrick Utility v1.5-hugebird============================================== Probing bus ... Done Instruction Length set to 5 CPU running under BIG endian CPU Chip ID: 00000110001101011000000101111111 (0635817F)*** Found a Broadcom BCM6358 Rev 1 CPU chip ***
- EJTAG IMPCODE ....... : 00000000100000011000100100000100 (00818904)
- EJTAG Version ....... : 1 or 2.0
- EJTAG DMA Support ... : Yes
- EJTAG Implementation flags: R4k MIPS16 MIPS32 Issuing Processor / Peripheral Reset ... DoneEnabling Memory Writes ... DoneHalting Processor ... <Processor did NOT enter Debug Mode!> ... DoneClearing Watchdog ... DoneInitialize EBI ... Skipped Probing Flash at (Probe Address: 0x1fc00000) ...
Match Flash Chip (VenID:DevID = 017e : 2101)*** Found a Spansion S29GL128N/P Uni
(16MB) Flash Chip ***
- Flash Chip Window Start .... : 1f000000
- Flash Chip Window Length ... : 01000000
- Selected Area Start ........ : 1f000000
- Selected Area Length ....... : 00040000 *** You Selected to Flash the CFE.BIN *** =========================Flashing Routine Started=========================Total Blocks to Erase: 2 Erasing block: 1 (addr = 1f000000)...DoneErasing block: 2 (addr = 1f020000)...Done Loading CFE.BIN to Flash Memory...Done
(CFE.BIN loaded into Flash Memory OK) =========================Flashing Routine Complete=========================elapsed time: 161 seconds
*** REQUESTED OPERATION IS COMPLETE *** C:\1\JTAG>

csssmx 发表于 2010-5-13 19:34:07

刷完还是PING不通192.168.1.1.

有大侠知道原因吗？

csssmx 发表于 2010-5-13 19:39:50

用了两个命令：输入 brjtag -probeonly /erasechip 全片擦除flash芯片数据
                   brjtag -flash:cfe                      写入CFE

是不是那里做的不对有总是？
请大家帮帮忙。

MINE 发表于 2010-5-13 19:55:17

可能是CFE.BIN文件不对。方法没错。
另外你可以试着换不同的LAN口试试（电脑网卡必须手动指定IP）

hotqj 发表于 2010-5-13 20:07:34

LZ要注意的是，你的Brjtag软件版本有点低了，有些问题。。。
S29GL128的Flash的起始地址是1e000000，而你现在显示的是1f000000
所以就算你的CFE正常写入，但设备读取的启动地址还是1e000000，由于你这个地方并没有写入新的CFE。所以问题还是原来的，没有改变。

解决，下载最新的Brjtag软件来使用，比如1.8C或者1.9A

kangnali 发表于 2010-5-13 21:06:08

5楼的能说下jtag怎么使用吗 我也准备刷2650 但是不知道怎么操作 已经刷成砖了 JTAG线已经连接好了

zzq0106 发表于 2010-5-13 21:50:45

线连好之后先不要开猫的电源
1,giveio.sys复制到windows\system32\drivers\下
2,运行loaddrv.exe把路径改成c:\windows\system32\drivers\giveio.sys，依次点install，start，ok
3,把cfe.bin复制到brjtag同一路径下，开始，运行，cmd，输入x:\brjtag -flash:cfe (x是brjtag所在的盘符)
，不要回车，此时打开猫的电源，看猫的一排指示灯一齐闪过之时按回车，如果成功的话会看到类似于
Probing bus ... Done
Instruction Length set to 5
CPU running under BIG endian
CPU Chip ID: 00000110001101011000000101111111 (0635817F)
*** Found a Broadcom BCM6358 Rev 1 CPU chip ***
*** You Selected to Flash the CFE.BIN ***
=========================
Flashing Routine Started
=========================
Total Blocks to Erase: 2
Erasing block: 1 (addr = 1f000000)...Done
Erasing block: 2 (addr = 1f020000)...Done
Loading CFE.BIN to Flash Memory...
Done
(CFE.BIN loaded into Flash Memory OK)
=========================
Flashing Routine Complete
=========================
elapsed time: 161 seconds
*** REQUESTED OPERATION IS COMPLETE ***
C:\1\JTAG>
这样的画面
然后关猫的电源，拔下jtag，接上ttl线和网线，打开超级终端，打开猫电源，会提示如下画面:
Code Address: 0x07038FD3, Entry Address: 0x109b1c90
Failed on decompression.Corrupted image?
CFE>
设好pc的ip为192.168.1.100,进入192.168.1.1，载入固件(建议用改版固件2009.4(基于Dlink DSL-2650U RU1.00带cfe)，刷完之后如果不能正常运行的话在cfe下输入f命令再刷一次，这次如果成功就再用cfe>e n清空nvram并重新配置参数即可

csssmx 发表于 2010-5-13 22:00:32

谢谢楼上的几位.后来在网上找到了个256K的CFE.刷过后.机器可以用了.
先这样用几天.有时间在试试新软件.

kangnali 发表于 2010-5-13 22:34:46

恭喜楼主 我的还在睡觉 努力努力把它救活 哈哈！

20076708 发表于 2010-5-13 22:53:46

学习中 准备试一试
页: [1]
查看完整版本: rg100a用JTAG刷机，显示如下，有没有问题？