rg100a 刷了几个版本的 一直不能拔号
CEF 如下 看看是什么原因 一直不能拔号 以前一直 可以 是后来刷成砖后 再用jatg和ttl线刷回 dlink 和联通红版 均可以进入设置界面 就是一直不能自动拔号上网Total memory used by CFE:0x80401000 - 0x80528280 (1208960)
Initialized Data: 0x8041DB50 - 0x8041F980 (7728)
BSS Area: 0x8041F980 - 0x80426280 (26880)
Local Heap: 0x80426280 - 0x80526280 (1048576)
Stack Area: 0x80526280 - 0x80528280 (8192)
Text (code) segment: 0x80401000 - 0x8041DB4C (117580)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id Name : 96358GW
Psi size in KB : 24
Number of MAC Addresses (1-32) : 12
Base MAC Address : 00:1f:a3:bf:51:d2
Ethernet PHY Type : External Switch Using Reverse MII
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1
web info: Waiting for connection on socket 0.
CFE>
CFE> b
Press:<enter> to use current value
'-' to go previous parameter
'.' to clear the current value
'x' to exit this command
Board Id Name (0-7)
96358SV -------0
96358VW -------1
96358VW-16 -------2
96358GW -------3
96358GW2 -------4
96358GW-16 -------5
96358M -------6
96358VW2 -------7 :3
Number of MAC Addresses (1-32) :12
Base MAC Address :00:1f:a3:bf:51:d2
PSI Size (1-64) KBytes :24
Main Thread Number :0
Base Ethernet PHY Number :11
Press any key to reset the board:
CFE version 1.0.37-6.5 for BCM96358 (32bit,SP,BE)
Build Date: Sun Apr 26 00:57:24 CST 2009 (root@MOD6538)
Copyright (C) 2000-2005 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x80528280 (1208960)
Initialized Data: 0x8041DB50 - 0x8041F980 (7728)
BSS Area: 0x8041F980 - 0x80426280 (26880)
Local Heap: 0x80426280 - 0x80526280 (1048576)
Stack Area: 0x80526280 - 0x80528280 (8192)
Text (code) segment: 0x80401000 - 0x8041DB4C (117580)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id Name : 96358GW
Psi size in KB : 24
Number of MAC Addresses (1-32) : 12
Base MAC Address : 00:1f:a3:bf:51:d2
Ethernet PHY Type : External Switch Using Reverse MII
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from latest image (0xbe800000) ...
Code Address: 0x80010000, Entry Address: 0x80238018
Decompression OK!
Entry at 0x80238018
Closing network.
Starting program at 0x80238018
Linux version 2.6.8.1 (root@MOD6538) (gcc version 3.4.2) #1 Sun Apr 26 14:06:49 CST 2009
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
96358GW prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 4000 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 29552k/32384k available (1803k kernel code, 2788k reserved, 400k data, 76k init, 0k highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80e00000 ... 0x80f00000>
Calibrating delay loop... 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...unavailable.
NET: Registered protocol family 16
Total Flash size: 16384K with 128 sectors
File system address: 0xbe800100
Can't analyze prologue code at 801d1684
SCSI subsystem initialized
usbcore: registered new driver hub
Initializing Cryptographic API
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v1.0
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0000300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0001400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x3 is enabled
SES: LED GPIO 0x8018 is enabled
======= GPIO CONFIG_BCM96358 init ========
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 76k freed
init started:BusyBox v1.00 (2009.04.26-06:08+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
BusyBox v1.00 (2009.04.26-06:08+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Feb 24 2009 16:12:15
Config Ethernet Switch Through MDIO Pseudo PHY Interface
dgasp: kerSysRegisterDyingGaspHandler: eth0 registered
eth0: MAC Address: 00:1F:A3:BF:51:D2
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 00:1F:A3:BF:51:D3
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.100.27.0.cpe2.1
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
I am in profile now...
eth0 Link UP.
BcmAdsl_Initialize=0xC005F3C8, g_pFnNotifyCallback=0xC0078324
AnnexCParam=0x7FFF7E88 AnnexAParam=0x00000980 adsl2=0x00000000
pSdramPHY=0xA1FFFFF8, 0x1C2FA 0xDEADBEEF
AdslCoreHwReset: AdslOemDataAddr = 0xA1FFD3D4
AnnexCParam=0x7FFF7E88 AnnexAParam=0x00000980 adsl2=0x00000000
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
ATM proc init !!!
==> Bcm963xx Software Version: RU_1.00 <==
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
Setting SSID "Dlink"
SIOCGIFFLAGS: No such device
Setting country code using abbreviation: "US"
wlctl: Not Found
wl0: current channel 11
device wl0 entered promiscuous mode
br0: port 2(wl0) entering learning state
br0: topology change detected, propagating
br0: port 2(wl0) entering forwarding state
ioctl, p_name=diapd
wlButtonInit open fd faild: No such device or address
*** diapwait system init 1 sec start
##############status LED blink now##################
*** diapwait system init 1 sec end
dft, wanIpAddress = , wanSubnetMask =
vpi = 0, vci = 0, conId = 0, portId = 0
nat = 0, firewall = 0
mount: Mounting /dev/sda1 on /opt failed: No such device or address
I am in p2popt now!
/proc/sys/net/ipv4/netfilter/ip_conntrack_generic_timeout: cannot create
/proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_established: cannot create
/proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_fin_wait: cannot create
/proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeout: cannot create
/proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeout_stream: cannot create
is not default cfg.
PIDUid VmSize Stat Command
1 admin 296 S init
2 admin SWN
3 admin SW<
4 admin SW<
5 admin SW<
6 admin SW
20 admin SW
21 admin SW
22 admin SW
23 admin SW<
28 admin SW
44 admin 348 S -sh
91 admin 1252 S cfm
127 admin 164 S pvc2684d
381 admin 284 S dhcpd
400 admin 1224 S snmpd
413 admin 1480 S httpd
414 admin 1368 S diapd
533 admin 312 R sh -c ps > /var/pslist
534 admin 300 R ps
Number of processes: 20
12:02amup 2 min,
load average: 1 min:0.27, 5 min:0.10, 15 min:0.03
total used free shared buffers
Mem: 29672 14596 15076 0 1588
Swap: 0 0 0
Total: 29672 14596 15076
kill snmpd process...
kill cfm process...
Killed
Finish profile script...!
# kill dhcpd process...
kill pvc2684d process...
modprobe: could not parse modules.dep
iptables v1.2.11: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
blaadd: blaa_cleanup entry
Remaining modules:
wl 760912 0 - Live 0xc0178000
bcm_enet 24800 0 - Live 0xc003f000
bcmprocfs 15216 0 - Live 0xc000e000
br2684 65760 0 - Live 0xc002e000
adsldd 141536 0 - Live 0xc005e000
atmapi 56672 2 br2684,adsldd, Live 0xc0020000
Memory info:
Number of processes: 17
12:02amup 2 min,
load average: 1 min:0.27, 5 min:0.10, 15 min:0.03
total used free shared buffers
Mem: 29672 14396 15276 0 1612
Swap: 0 0 0
Total: 29672 14396 15276
remove module vnet
is not default cfg.
br0: port 2(wl0) entering disabled state
CFE version 1.0.37-6.5 for BCM96358 (32bit,SP,BE)
Build Date: Sun Apr 26 00:57:24 CST 2009 (root@MOD6538)
Copyright (C) 2000-2005 Broadcom Corporation.
Boot Address 0xbe000000 wlButtonInit open fd faild: No such device or address
老是这个错误！！ 晕自己装了一个虚拟网卡作怪 ！现在刷成砖了 明天用jatg恢复一下！再看还能不能拔号！ 网卡 去掉了 重刷还是不能拔号！怪 在成砖之前好好的 现在居然不能拔号！
页:
[1]