H618B 刷TT或者DD后如何让IPTV通过网线PPPoE拨号
H618B 刷TT或者DD后如何让IPTV通过网线PPPoE拨号各位大侠,
我的H618B原厂固件时,Wan口通过网线PPPoE拨号上网,原厂固件中,设置捆绑Lan1,Lan3,Lan4和无线为internet连接,
Lan2口设置bridge模式,为IPTV连接.各自分布拨号上网.
刷了TT或者DD固件后,直接将IPTV设备网线连接在Lan2口上无法拨号成功.现在只能通过telnet到H618B上设置.
由于对网络设备不是很熟悉,求教各位如何设置端口Lan2和Wan口桥接,使得IPTV设备可以拨号成功.同时不影响其他端口的上网连接.
以下是H618B的信息,当前固件为DD-WRT v24-sp1 std,(dd-wrt.v24_std_generic.bin)
以下是ifconfig内容,其中mac为51的是H618B路由设备 52为Wan口,53为无线网络
H618B的端口,Wan Lan1 Lan2 Lan3 Lan4 Cpu 分布对应ports 0 1 2 3 4 5
我的目标是桥接Lan2 和Wan,
系统默认是Lan/port 1,2,3,4 做成vlan0,Wan口是vlan1, br0 包含了vlan0 和 eth1(eth1是无线网络)
我尝试过,将Lan2 设置为单独的vlan2,然后在DD管理界面设置br1,assign vlan2和vlan1到br1,但是不仅IPTV拨号不成功,而且其他端口的电脑业没法上网.
我有个疑问就是一个vlan是不是可以assign给不同的网桥,或者是建立不同的eth针对不同的port?
谢谢各位大侠帮助.
br0 Link encap:EthernetHWaddr 00:00:00:00:00:51
inet addr:192.168.1.1Bcast:192.168.1.255Mask:255.255.255.0
UP BROADCAST RUNNING MULTICASTMTU:1500Metric:1
RX packets:11854 errors:0 dropped:0 overruns:0 frame:0
TX packets:12792 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2252181 (2.1 MiB)TX bytes:10411522 (9.9 MiB)
br0:0 Link encap:EthernetHWaddr 00:00:00:00:00:51
inet addr:169.254.255.1Bcast:169.254.255.255Mask:255.255.0.0
UP BROADCAST RUNNING MULTICASTMTU:1500Metric:1
eth0 Link encap:EthernetHWaddr 00:00:00:00:00:51
UP BROADCAST RUNNING MULTICASTMTU:1500Metric:1
RX packets:54639 errors:0 dropped:0 overruns:0 frame:0
TX packets:39903 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:51258467 (48.8 MiB)TX bytes:6833000 (6.5 MiB)
Interrupt:4
eth1 Link encap:EthernetHWaddr 00:00:00:00:00:53
UP BROADCAST RUNNING MULTICASTMTU:1500Metric:1
RX packets:26378 errors:0 dropped:0 overruns:0 frame:8859290
TX packets:36706 errors:10 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:3929256 (3.7 MiB)TX bytes:44188134 (42.1 MiB)
Interrupt:2 Base address:0x5000
lo Link encap:Local Loopback
inet addr:127.0.0.1Mask:255.0.0.0
UP LOOPBACK RUNNING MULTICASTMTU:16436Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B)TX bytes:0 (0.0 B)
ppp0 Link encap:Point-to-Point Protocol
inet addr:58.88.88.88P-t-P:58.88.88.1Mask:255.255.255.255
UP POINTOPOINT RUNNING MULTICASTMTU:1492Metric:1
RX packets:15468 errors:0 dropped:0 overruns:0 frame:0
TX packets:9255 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:14348249 (13.6 MiB)TX bytes:1937350 (1.8 MiB)
vlan0 Link encap:EthernetHWaddr 00:00:00:00:00:51
UP BROADCAST RUNNING MULTICASTMTU:1500Metric:1
RX packets:28406 errors:0 dropped:0 overruns:0 frame:0
TX packets:21076 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:35198098 (33.5 MiB)TX bytes:3906990 (3.7 MiB)
vlan1 Link encap:EthernetHWaddr 00:00:00:00:00:52
UP BROADCAST RUNNING MULTICASTMTU:1500Metric:1
RX packets:26232 errors:0 dropped:0 overruns:0 frame:0
TX packets:18827 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:15076821 (14.3 MiB)TX bytes:2503484 (2.3 MiB)
root@Super:~# brctl show
bridge name bridge id STP enabled interfaces
br0 8000.00904cc00451 no vlan0
eth1
root@Super:~# nvram show |grep vlan
vlan0ports=1 3 4 5*
vlan0_bridged=1
port5vlans=0 1 16
port3vlans=0 18 19
vlan2_ipaddr=0.0.0.0
vlan2_multicast=0
port1vlans=0 18 19
wl0_vlan_prio_mode=off
wan_ifname2=vlan1
pppoe_wan_ifname=vlan1
vlan1_bridged=1
lan_ifnames=eth2 eth3 vlan0 eth1
vlan0_multicast=0
wan_default=vlan1
wan_ifnames=vlan1
vlan1hwname=et0
size: 19408 bytes (13360 left)
vlan1ports=0 5u
vlan2_bridged=1
port4vlans=0 18 19
vlans=1
vlan_tagcount=0
port2vlans=18 19
vlan2_netmask=0.0.0.0
port0vlans=1 18 19
wan_ifname=vlan1
landevs=vlan0 wl0
vlan_tags=
vlan0hwname=et0
vlan1_multicast=0 普通TT或DD路由能设置某LAN口为bridge模式吗？是不是设为bridge模式，就能连IPTV了
dolce 发表于 2010-5-15 23:21 https://www.chinadsl.net/images/common/back.gif
理论上是这样的。 貌似不行，刷后就不能设置某个LAN口桥接了。
楼主只能在路由器前面加个小交换机了 本帖最后由 juy911 于 2010-5-26 00:20 编辑
机顶盒里面也有设定3中不同的接入方式：pppoe DHCP静态ip，你改一下介入方式就可以了！我今天把自己的机顶盒接入设为固定ip，直接接上路由器就可以看了！
页:
[1]