求助：DB120-B1刷了带CFE原版固件出问题
本帖最后由 ljyzj 于 2010-4-24 21:27 编辑我昨晚刷了本论坛的v3.1-cfe-128k固件，在SecureCRT下显示以下信息：
CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: 二1月 29 07:41:15 CST 2008 (root@ZTJ)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device id 0279 is not supported.
*** Board is not initialized properly ***
Press:<enter> to use current value
'-' to go previous parameter
'.' to clear the current value
'x' to exit this command
96358VW2 ------- 0
96358VW ------- 1
96358GWVG ------- 2
96358MV2G ------- 3
96358M ------- 4
96358B ------- 5
96358BGWE_OEM1 ------- 6
96359PONG ------- 7
96358SV ------- 8
96358VW2_b20 ------- 9
Board Id (0-9) :
请问是不是已经变砖了，还有救吗？另外，在SecureCRT和超级终端中为什么无法执行命令，是不是TTL线有问题；请刷机有经验的朋友指教。 Board Id (0-9) :
选 0 选“0”输入没有反应，命令不能执行，不知道是什么原因。 根据本论坛的教程，重新接好TTL线，再次进入cfe，刷几次，但是后来一刷就断网，不知道是什么原因，请高手赐教。
刷机显示信息如下：
96358VW2 ------- 0
96358VW ------- 1
96358GWVG ------- 2
96358MV2G ------- 3
96358M ------- 4
96358B ------- 5
96358BGWE_OEM1 ------- 6
96359PONG ------- 7
96358SV ------- 8
96358VW2_b20 ------- 9
Board Id (0-9) :0
Number of MAC Addresses (1-32) :012
Base MAC Address :00:00:00:00:00:0000:25:5E:1D:4E:50
PSI Size (1-64) KBytes :24
Flash Block Size (1-128) in KBytes:0128
Auxillary File System Size Percent:025
Main Thread Number :0
Flash layout changed. Need to erase all flash except bootrom
Invalid command: "e"
Available commands:
Flash Layout: Boot Kern[-1,0xbdffffff]
AuxFS[-1,0x00000000] Misc[-1,0x00000000] PSI[-1,0x00000000]
Flash RootFS Partition Length: 1107296257
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x805285A0 (1209760)
Initialized Data: 0x8041DD30 - 0x8041FDC0 (8336)
BSS Area: 0x8041FDC0 - 0x804265A0 (26592)
Local Heap: 0x804265A0 - 0x805265A0 (1048576)
Stack Area: 0x805265A0 - 0x805285A0 (8192)
Text (code) segment: 0x80401000 - 0x8041DD30 (118064)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Use default boot line parameters: e=192.168.1.1:ffffff00 h=192.168.1.159 g= r=h
f=308nfs6358 i=bcm963xx_fs_kernel d=1 p=0
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.159
Gateway IP address :
Run from flash/host (f/h) : h
Default host run file name : 308nfs6358
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-9) :
Number of MAC Addresses (1-32) : 0
Base MAC Address : 00:00:00:00:00:00
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 0
Auxillary File System Size Percent: 0
Main Thread Number : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1
web info: Waiting for connection on socket 0.
CFE>
不知道怎么回事，没有办法继续设置，我怀疑挂了。 本帖最后由 sxj1234 于 2010-4-26 06:35 编辑
CFE>b
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.159
Gateway IP address :
Run from flash/host (f/h) : h
Default host run file name : 308nfs6358
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-4) : 96358VW2
Number of MAC Addresses (1-32) : 24
Base MAC Address : 00:1e:4w:87:0a:2w
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number : 0 输入CFE>b
之后，又会重复出现以下信息：
96358VW2 ------- 0
96358VW ------- 1
96358GWVG ------- 2
96358MV2G ------- 3
96358M ------- 4
96358B ------- 5
96358BGWE_OEM1 ------- 6
96359PONG ------- 7
96358SV ------- 8
96358VW2_b20 ------- 9
Board Id (0-9) :0 Board Id (0-9) :
选 0 有了这句话“Parallel flash device id 0279 is not supported.
”基本可以确认变砖，只能重写Flash，需要编程器及风枪。
页:
[1]