求助大亚DB120 B1变砖！TTL线连接显示如下！！
CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)Build Date: Thu May 10 22:28:34 CST 2007 (root@localhost.localdomain)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device id 0279 is not supported.
*** Board is not initialized properly ***
Press:<enter> to use current value
'-' to go previous parameter
'.' to clear the current value
'x' to exit this command
96358VW2 ------- 0
96358VW ------- 1
96358GWVG ------- 2
96358MV2G ------- 3
96358M ------- 4
96358B ------- 5
96358BGWE_OEM1 ------- 6
96359PONG ------- 7
96358SV ------- 8
Board Id (0-8) 请问高手下来怎么设置啊！！！ 这就叫砖了？
DB120-B1 在多数固件 Board Id要选 VW2，也就是 0，
刷之前也要多看看教程嘛。
我的DB120-WG 刷 LINPHUN 固件成功后的TTL 信息，给你参考：
Board Id (0-8) : 96358VW2
Number of MAC Addresses (1-32) : 11
Base MAC Address : 02:18:26:20:0b:01
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number : 0
设置完成，就会自动重启的。 LS的大哥我选了啊！！结果在出现
**Exception 32: EPC=00000000, Cause=39504F4E (Exc19 )
RA=00000000, VAddr=20202020
0($00) = 30303030 AT ($01) = 00707429
v0 ($02) = 00000000 v1 ($03) = 00000000
a0 ($04) = 00000000 a1 ($05) = 00000000
a2 ($06) = 00000000 a3 ($07) = 00000000
t0 ($08) = 00000000 t1 ($09) = 00000000
t2 ($10) = 00000000 t3 ($11) = 00000000
t4 ($12) = 00000000 t5 ($13) = 00000000
t6 ($14) = 00000000 t7 ($15) = 00000000
s0 ($16) = 00000000 s1 ($17) = 00000000
s2 ($18) = 00000000 s3 ($19) = 00000000
s4 ($20) = 00000000 s5 ($21) = 00000000
s6 ($22) = 00000000 s7 ($23) = 00000000
t8 ($24) = 00000000 t9 ($25) = 00000000
k0 ($26) = 00000000 k1 ($27) = 00000000
gp ($28) = 00000000 sp ($29) = 00000000
fp ($30) = 00000000 ra ($31) = 00000000
就没反应了，光标不动了，键盘没反应了 {{gangzai26{{帮帮我吧 貌似得刷2便的吧? 每次都是跳到 0($00) = 30303030 AT ($01) = 00707429
v0 ($02) = 00000000 v1 ($03) = 00000000
a0 ($04) = 00000000 a1 ($05) = 00000000
a2 ($06) = 00000000 a3 ($07) = 00000000
t0 ($08) = 00000000 t1 ($09) = 00000000
t2 ($10) = 00000000 t3 ($11) = 00000000
t4 ($12) = 00000000 t5 ($13) = 00000000
t6 ($14) = 00000000 t7 ($15) = 00000000
s0 ($16) = 00000000 s1 ($17) = 00000000
s2 ($18) = 00000000 s3 ($19) = 00000000
s4 ($20) = 00000000 s5 ($21) = 00000000
s6 ($22) = 00000000 s7 ($23) = 00000000
t8 ($24) = 00000000 t9 ($25) = 00000000
k0 ($26) = 00000000 k1 ($27) = 00000000
gp ($28) = 00000000 sp ($29) = 00000000
fp ($30) = 00000000 ra ($31) = 00000000
就没有反应了 要确定你的DB120-B1 闪存类型是否属于能刷大家都在用的公用固件。我的是S29GL128P 10TF01，
要是现在还能在开机时按任意键中断路由器的启动，出现 CFE> 后 ，再PING 192.168.1.1 还能PING 通的话，登录192.168.1.1 的升级页面，进行2次 不带CFE 的固件的刷新。 带CFE 的一遍就行了。
具体参考：https://www.chinadsl.net/thread-28078-1-1.html 我已经认真看了！！！我连接号TTL线，一打开猫的电源就
出现
*** Board is not initialized properly ***
Press:<enter> to use current value
'-' to go previous parameter
'.' to clear the current value
'x' to exit this command
96358VW2 ------- 0
96358VW ------- 1
96358GWVG ------- 2
96358MV2G ------- 3
96358M ------- 4
96358B ------- 5
96358BGWE_OEM1 ------- 6
96359PONG ------- 7
96358SV ------- 8
Board Id (0-8) :1
Number of MAC Addresses (1-32) :012
Base MAC Address :00:00:00:00:00:0000:1E:40:F2:A5:2D
PSI Size (1-64) KBytes :2424
Flash Block Size (1-128) in KBytes:064
Auxillary File System Size Percent:025
Main Thread Number :00
Flash layout changed. Need to erase all flash except bootrom
Invalid command: "e"
Available commands:
Flash Layout: Boot Kern[-1,0xbdffffff]
AuxFS[-1,0x00000000] Misc[-1,0x00000000] PSI[-1,0x00000000]
Flash RootFS Partition Length: 1107296257
100 MB Full-Duplex (auto-neg)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x80528200 (1208832)
Initialized Data: 0x8041DA80 - 0x8041FA20 (8096)
BSS Area: 0x8041FA20 - 0x80426200 (26592)
Local Heap: 0x80426200 - 0x80526200 (1048576)
Stack Area: 0x80526200 - 0x80528200 (8192)
Text (code) segment: 0x80401000 - 0x8041DA80 (117376)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Use default boot line parameters: e=192.168.1.1:ffffff00 h=192.168.1.100 g= r=f f=vmlinux i=bcm963xx_fs_kernel d=1 p=0
** Flash image not found. **
**Exception 32: EPC=8041C9B0, Cause=804074AC (CoProcUnu)
RA=DFAE3CFC, VAddr=80527F31
0($00) = 382E312E AT ($01) = 66666666
v0 ($02) = 3D313932 v1 ($03) = 80527F5F
a0 ($04) = 3D20723D a1 ($05) = 80420000
a2 ($06) = 00000001 a3 ($07) = 80420000
t0 ($08) = 00000001 t1 ($09) = 20703D30
t2 ($10) = 00000000 t3 ($11) = 00000000
t4 ($12) = 466C6173 t5 ($13) = 61676520
t6 ($14) = 666F756E t7 ($15) = 2A0A0A00
s0 ($16) = 00000000 s1 ($17) = 00000000
s2 ($18) = 00000000 s3 ($19) = 00000000
s4 ($20) = 00000000 s5 ($21) = 00000000
s6 ($22) = 00000000 s7 ($23) = 00000000
t8 ($24) = 8041FAD0 t9 ($25) = 80528028
k0 ($26) = DFAE3CFC k1 ($27) = 804391CC
gp ($28) = 0000012C sp ($29) = 00000000
fp ($30) = 9EFA7CD1 ra ($31) = DFAE3CFC 本帖最后由 xhh2001 于 2010-4-17 13:58 编辑
看到我 3楼的回复吗？
DB120 闪存是16M ，
Flash Block Size (1-128) in KBytes: 128
这项要选 128 才行吧。
实在不行，只要CFE 还健在，就再刷其他合适的固件。
页:
[1]
2