长虹RG200e串口输出，和6358一样的核心
刚才刷了G130，弄死了之后，想起rg200e没接上串口试试。下面是设备启动的串口输出信息 Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot Kern
AuxFS Misc PSI
Flash RootFS Partition Length: 12058624
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x80529370 (1213296)
Initialized Data: 0x8041E550 - 0x80420B80 (9776)
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-8) : 96358VW2
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:1e:e3:00:1e:1a
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number : 0
udp_send finished
No answer .auto boot ...
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 110
Code Address: 0x80010000, Entry Address: 0x8024f018
Decompression OK!
Entry at 0x8024f018
Closing network.
Starting program at 0x8024f018
Linux version 2.6.8.1 (root@panyan) (gcc version 3.4.2) #4 Fri Mar 14 12:51:31 EDT 2008
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
fInfo.flash_rootfs_available_length = 16252928
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 4000 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Allocating memory for DSP module core and initialization code
Allocated DSP module memory - CORE=0x8104ca80 SIZE=615168, INIT=0x0 SIZE=0
Memory: 28860k/32384k available (1871k kernel code, 3480k reserved, 424k data, 76k init, 0k highmem)
Calibrating delay loop... 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...unavailable.
NET: Registered protocol family 16
Total Flash size: 16384K with 128 sectors
Computing partition layout for flash of size sectors
Flash split 25% into RootFS+Kernel : AuxFS
Partition ROOTFS_KRN Blks[ 92: 1 ..92]
SubPartition Image 1 Blks[ 46: 1 ..46]
SubPartition Image 2 Blks[ 46:47 ..92]
Blk# BlkOff Blks BlkSize AvailSize MemStart MemLen Partition Name
0 1408 1131072 131072 0xbe000580 1024 BOOTLOADER
1 0 9213107212058624 0xbe020000 12058624 ROOTFS_KRN
93 0 32131072 4194304 0xbeba0000 4194304 JFFS_AUXFS
125 0 1131072 131072 0xbefa0000 131072 LOG_SCRPAD
126 106496 1131072 131072 0xbefda000 24576 TW_PERSISTMEM
127 106496 1131072 131072 0xbeffa000 24576 PERSISTMEM
Can't analyze prologue code at 801e2684
SCSI subsystem initialized
usbcore: registered new driver hub
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v2.0
File system address: 0xbe020100
Registered device mtd dev Flash
Registered device mtd dev Flash
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0050300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0052400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x4 is enabled
WIFI: Button Interrupt 0x3 is enabled
WIFI: map_external_irq begin
SES: LED GPIO 0x8019 is enabled
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
initLed: led: mask=0x0100, state=0
initLed: led: mask=0x2000000, state=0
initLed: led: mask=0x800000, state=0
initLed: led: mask=0x0001, state=0
initLed: led: mask=0x0004, state=0
initLed: led: mask=0x0010, state=0
initLed: led: mask=0x0040, state=0
initLed: led: mask=0x0080, state=0
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
u32 classifier
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 76k freed
init started:BusyBox v1.00 (2008.03.14-15:34+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
BusyBox v1.00 (2008.03.14-15:34+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
bcmprocfs: module license 'Proprietary' taints kernel.
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Mar 14 2008 11:25:25
Config Internal PHY Through MDIO
BCM63xx_ENET: Auto-negotiation timed-out
BCM63xx_ENET: 10 MB Half-Duplex (assumed)
kerSysGetMacAddress:ulId=2
eth0: MAC Address: 00:1E:E3:00:1E:1A
Broadcom BCM6358A1 Ethernet Network Device v0.3 Mar 14 2008 11:25:25
Config Ethernet Switch Through MDIO Pseudo PHY Interface
dgasp: kerSysRegisterDyingGaspHandler: eth1 registered
kerSysGetMacAddress:ulId=3
eth1: MAC Address: 00:1E:E3:00:1E:1A
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
kerSysGetMacAddress:ulId=2003566592
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 00:1E:E3:00:1E:1B
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.150.10.15.cpe2.2
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
DSP Driver: DSP init stub
Endpoint: endpoint_init entry
BOS: Enter bosInit
Enter bosAppInit
Exit bosAppInit
BOS: Exit bosInit
Endpoint: endpoint_init COMPLETED
BcmCfg_recover, L335: Waiting Usb init complete
##no usb device22
--------------------in psiifc.cpp profileGetFromFlash() 1
--------------------in psiifc.cpp profileGetFromFlash() 2
--------------------in psiifc.cpp profileGetFromFlash() 3
---- nxml_write(): len 9914
xmlEndPMapFltObj(calling cfm to get appName PMapCfg, objName pmapFlt
==func:xmlEndFtpSrvObjNode==, objName:account1
==func:xmlEndFtpSrvObjNode==, objName:account2
==func:xmlEndFtpSrvObjNode==, objName:account3
==func:xmlEndFtpSrvObjNode==, objName:srvParams
****************************************if(strstr(tag_name,psitree)==NULL){
****************************************xmlTagEnd():Iwant
xmlState.state == state_psi_end 3
xmlState.state =2, errorFlag=0
TWprofileGetFromFlash =============
---- nxml_write(): len 9914
xmlEndPMapFltObj(calling cfm to get appName PMapCfg, objName pmapFlt
==func:xmlEndFtpSrvObjNode==, objName:account1
==func:xmlEndFtpSrvObjNode==, objName:account2
==func:xmlEndFtpSrvObjNode==, objName:account3
==func:xmlEndFtpSrvObjNode==, objName:srvParams
****************************************if(strstr(tag_name,psitree)==NULL){
****************************************xmlTagEnd():Iwant
xmlState.state == state_psi_end 3
xmlState.state =2, errorFlag=0
psi_status = 0, tw_psi_status = 0 --------------------in psiifc.cpp profileGetFromFlash() 1
--------------------in psiifc.cpp profileGetFromFlash() 2
--------------------in psiifc.cpp profileGetFromFlash() 3
---- nxml_write(): len 9914
BcmDb_setPMapInfo: id=2
xmlEndPMapFltObj(calling cfm to get appName PMapCfg, objName pmapFlt
BcmDb_setPMapInfo: id=5
==func:xmlEndFtpSrvObjNode==, objName:account1
==func:xmlEndFtpSrvObjNode==, objName:account2
==func:xmlEndFtpSrvObjNode==, objName:account3
==func:xmlEndFtpSrvObjNode==, objName:srvParams
****************************************if(strstr(tag_name,psitree)==NULL){
****************************************xmlTagEnd():Iwant
xmlState.state == state_psi_end 3
xmlState.state =2, errorFlag=0
get qos queue policy type error
Enable = 1
enter QosPriorityQueueTbl::removeAllTCRules
==> Bcm963xx Software Version: RG200E_V1.0 <==
BcmNtwk_initLan BcmNtwk_initIPv4
BcmNtwk_initLan BcmNtwk_setBridgeName
BcmNtwk_initLan bcmStoreDeviceInfoToProcFile
BcmNtwk_initLan HPNA
BcmNtwk_initLan USB
BcmNtwk_initLan Ethernet
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
BcmNtwk_initLan LAN2
BcmNtwk_initLan BcmNtwk_initLan
BcmNtwk_initLan BcmNtwk_initFirewall
BcmNtwk_initLan BcmNtwk_initDosProtect
BcmNtwk_initLan BcmNtwk_initAlg
BcmNtwk_initLan BcmNtwk_initFactoryMode
buffer=2.6.8.1
-----insmod=insmod /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_conntrack_devicectl.ko ip_begin=3232235777 ip_end=3232236030mode=1 maxTotalNumber=4 maxComputerNumber=1 maxStbNumber=0 maxCameraNumber=1 computerStatus=0 stbStatus=0 cameraStatus=0
ip_conntrack_devicectl: load success
BcmNtwk_initLan BcmNtwk_loadDeviceModule
BcmNtwk_initLan BcmWl_Init_All
ses_led_off_ex I want
ctlstate = 0x0
recv action = 0
recv event = 0x0
blinktype=0, event=0, status=0
Setting SSID "SSID1"
Setting SSID "Guest2"
Setting SSID "Guest3"
Setting SSID "Guest4"
Setting country code using abbreviation: "ALL"
channel 11 selected
device wl0 entered promiscuous mode
br0: port 2(wl0) entering learning state
br0: topology change detected, propagating
br0: port 2(wl0) entering forwarding state
device wl0.1 entered promiscuous mode
br0: port 3(wl0.1) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0.1) entering forwarding state
device wl0.2 entered promiscuous mode
br0: port 4(wl0.2) entering learning state
br0: topology change detected, propagating
br0: port 4(wl0.2) entering forwarding state
device wl0.3 entered promiscuous mode
br0: port 5(wl0.3) entering learning state
br0: topology change detected, propagating
br0: port 5(wl0.3) entering forwarding state
br0: port 3(wl0.1) entering disabled state
br0: port 4(wl0.2) entering disabled state
br0: port 5(wl0.3) entering disabled state
BcmNtwk_initLan BcmWl_Init_All 2
BcmNtwk_initLan BcmNtwk_initWan
mii register 0 is 0x1000
BcmNtwk_initLan BcmRcm_init
BcmNtwk_initLan BcmPMcm_init
eth1.2: MAC Address: 00:1E:E3:00:1E:1A
eth1.3: MAC Address: 00:1E:E3:00:1E:1A
eth1.4: MAC Address: 00:1E:E3:00:1E:1A
eth1.5: MAC Address: 00:1E:E3:00:1E:1A
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
device eth0 left promiscuous mode
br0: port 1(eth0) entering disabled state
device wl0 left promiscuous mode
br0: port 2(wl0) entering disabled state
device wl0.1 left promiscuous mode
br0: port 3(wl0.1) entering disabled state
device wl0.2 left promiscuous mode
br0: port 4(wl0.2) entering disabled state
device wl0.3 left promiscuous mode
br0: port 5(wl0.3) entering disabled state
device wl0 entered promiscuous mode
br0: port 1(wl0) entering learning state
br0: topology change detected, propagating
br0: port 1(wl0) entering forwarding state
device eth1.2 entered promiscuous mode
br0: port 2(eth1.2) entering learning state
br0: topology change detected, propagating
br0: port 2(eth1.2) entering forwarding state
device eth1.3 entered promiscuous mode
br0: port 3(eth1.3) entering learning state
br0: topology change detected, propagating
br0: port 3(eth1.3) entering forwarding state
device eth1.4 entered promiscuous mode
br0: port 4(eth1.4) entering learning state
br0: topology change detected, propagating
br0: port 4(eth1.4) entering forwarding state
device eth1.5 entered promiscuous mode
br0: port 5(eth1.5) entering learning state
br0: topology change detected, propagating
br0: port 5(eth1.5) entering forwarding state
device wl0.1 entered promiscuous mode
br0: port 6(wl0.1) entering learning state
br0: topology change detected, propagating
br0: port 6(wl0.1) entering forwarding state
device wl0.2 entered promiscuous mode
br0: port 7(wl0.2) entering learning state
br0: topology change detected, propagating
br0: port 7(wl0.2) entering forwarding state
device wl0.3 entered promiscuous mode
br0: port 8(wl0.3) entering learning state
br0: topology change detected, propagating
br0: port 8(wl0.3) entering forwarding state
BcmNtwk_initLan BcmPMcm_init 2
BcmNtwk_initLan BcmWl_startService
BcmNtwk_initLan SUPPORT_CERT
BcmNtwk_initLan BcmNtwk_initSysLog
CT SystemLog Init Read From Flash string lenth =12296
CT SystemLog Init Read From Flash string acsloglenth =2333 secloglenth=825
BcmNtwk_initLan BcmNtwk_initDns
BcmNtwk_initLan SUPPORT_DDNSD
BcmNtwk_initLan SUPPORT_SNTP
BcmNtwk_initLan BcmNtwk_initIgmpSnp
BcmNtwk_initLan BcmNtwk_initMacFilter
sntp: host not found
Voice App. Comparing interface: current br0 (3) - passed br0.
Voice App. Comparing interface: current br0 (3) - passed br0.
iptables v1.2.11: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
iptables v1.2.11: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
iptables v1.2.11: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
iptables v1.2.11: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
iptables v1.2.11: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
iptables v1.2.11: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
iptables v1.2.11: can't initialize iptables table `mangle': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
iptables v1.2.11: can't initialize iptables table `mangle': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
iptables v1.2.11: can't initialize iptables table `mangle': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
iptables v1.2.11: can't initialize iptables table `mangle': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
Starting the SIP application with the following parameters:
SIP Proxy (IP address or FQDN): 0.0.0.0
SIP Proxy port: 5060
SIP Outbound Proxy (IP address or FQDN): 0.0.0.0
SIP Outbound Proxy port: 5060
SIP Registrar (IP address or FQDN): 0.0.0.0
SIP Registrar Port port: 5060
Bak SIP Proxy (IP address or FQDN): 0.0.0.0
Bak SIP Proxy port: 5060
Bak SIP Outbound Proxy (IP address or FQDN): 0.0.0.0
Bak SIP Outbound Proxy port: 5060
Bak SIP Registrar (IP address or FQDN): 0.0.0.0
Bak SIP Registrar port: 5060
Hang on and no dial time: 15
No dial time between digit and digit: 5
Long dial but no answer time: 60
Warnning time: 60
Busy time: 40
Jitter buffer: auto
heartOption: 60
Echo Restain Enable: YES
RFC2833 Payload: 97
sipDscpMark: 0
rtpDscpMark: 0
SIP VLAN ID Mark: 0
RTP VLAN ID Mark: 0
SIP 802.1p Mark: 0
RTP 802.1p Mark: 0
SIP EthernetPriority Mark: 0
RTP EthernetPriority Mark: 0
Enable SIP tag matching: Yes
Log IP address: 192.168.1.100
Log port: 55555
Music server address: 0.0.0.0
Music server port: 5060
Extension 1: Disabled
Password 1: Disabled
Interface name: br0
Domain name:
Locale name: CHN
Pref. codec: none
Pref. ptime: 20
Console log level: 5
Line 1 call forwarding number: Not available
Line 1 call forwarding busy: Disabled
Line 1 call forwarding all: Disabled
Line 1 call forwarding no answer: Disabled
Line 1 call waiting: Disabled
BcmNtwk_initLan PORT_MIRRORING
BcmNtwk_initLan BcmCfm_init
BOS: Enter bosInit
bosTimerInit
Enter bosAppInit
Exit bosAppInit
BOS: Exit bosInit
BCM Release is: ver6_20070725_001!!!
Created queue CFGMGR_Q
00:00:49 Init Configuration Manager: CFGMGR_VOIP_RETCODE_SUCCESS
00:00:49 Setting provisioning default values.
voipqosapi: sendto returned 2
phone dial timer length = 15000(ms)
phone no digit timer length = 5000(ms)
phone no answer timer length = 60000(ms)
phone warnning timer length = 60000(ms)
phone busy timer length = 40000(ms)
jitter buffer = auto
options heartbeat timer length = 60(ms)
echo cancealer enabled
dtmf relay method = 0
option A callfwd busy = 0
option A callfwd all = 0
option A callfwd no answer = 0
option A callwaiting = 0
Sip registration timeout = 3600Sip transport protocol = 1User line enabled = 14
user line 1 mwi enabled = 0
Codec name = G722
Codec name = G711U
Codec name = G711A
Codec name = G729
T38 fax enabled
T38 and g711fax enabled
VAD enabled
voipqosapi: sendto returned 2
00:00:50 Process 737 priority is 0
00:00:50 Process 737: old priority 0, new priority -15
Enter TaskCreate VRGCMGR
TaskCreate - spawn new task VRGCMGR
Exit TaskCreate
kernel::endpoint_open
kernel::endpoint_open COMPLETED
00:00:50 Endpoint Event task started with pid 749...
00:00:50 Endpoint Packet task started with pid 750 ...
Enter bosStartApp
bosAppRootTask() - Is it morning already? Spawning app task (epoch #0)...
bosAppRootTask() - Is it morning already? Spawning app task (epoch #0)...
Enter TaskCreate aoAP
TaskCreate - spawn new task aoAP
Exit TaskCreate
AppResetDetectionEnable() - Enabled reset detection.
Exit bosStartApp
PLL init completed. PLL registers set to:
PCM->pcm_pll_ctrl1 = 0x00020001
PCM->pcm_pll_ctrl2 = 0x0008492B
PCM->pcm_pll_ctrl3 = 0x00001E1C
Set up PCM registers
Channel 0 assigned to timeslot 0
Channel 1 assigned to timeslot 8
Channel 2 assigned to timeslot 1
Channel 3 assigned to timeslot 9
Tx Desc (0xA0FEB000): chan 0, buf 0, sts 0xe000, len 1280, bufp 0xd28000
Tx Desc (0xA0FEB008): chan 0, buf 1, sts 0x7000, len 1280, bufp 0xd28510
Rx Desc (0xA0E64000): chan 0, buf 0, sts 0x8000, len 1280, bufp 0x92e000
Rx Desc (0xA0E64008): chan 0, buf 1, sts 0x9000, len 1280, bufp 0x92e510
initIudma: chan 0, descBase 0xa0e64000, descBaseIudma 0xe64000
initIudma: chan 1, descBase 0xa0feb000, descBaseIudma 0xfeb000
PCM ENABLE INFO: DMA0 IRQ STATUS 0x00000000
PCM ENABLE INFO: DMA0 IRQ MASK 0x00000005
PCM ENABLE INFO: DMA1 IRQ STATUS 0x00000000
PCM ENABLE INFO: DMA1 IRQ MASK 0x00000005
PCM ENABLE INFO: PCMIRQ MASK 0x00000003
PCM ENABLE INFO: PCMIRQ PENDING 0x00000007
Enter TaskCreate CMT_EXCEPTION_IST
TaskCreate - spawn new task CMT_EXCEPTION_IST
Exit TaskCreate
regStatus (reg 12 sel 0) = 0x10008501
regStatus (reg 12 sel 7) = 0x00000101
regCause(reg 13 sel 0) = 0x00000000
regCause(reg 13 sel 7) = 0x00808000
regCMT (reg 22 sel 0) = 0xe30e1006
regCMT (reg 22 sel 1) = 0x10008001
Kicking off secondary thread processor at entry point 0x8104CAC0...
Secondary thread processor entry point at 0x8104cac0
Thread processor handshake. Secondary app initialized properly.
Enter TaskCreate HTSK
TaskCreate - spawn new task HTSK
Exit TaskCreate
SUCCESS: Took semaphore
SUCCESS: Gave semaphore
INFO: MSPI POLLING MODE
INFO: IRQ MASK 0xd8128624
INFO: IRQ STATUS 0x400000
INFO: BLOCK ENABLES 0x3e0320
MSPI INITIALIZED
boardHalSlicInit: slictype=0
slicConfigure() reading 0 from slic 0 devId 1
slicConfigure() reading 3 from slic 0 devId 1
Read Si3216 Revision H on slic 0
Direct read/write test passed on slic 0
Indirect read/write test passed on slic 0
Entering SLIC DC Power Calibration check ......Passed
Entering SLIC Calibration check................Passed
Entering Manual Calibration check................BcmNtwk_initLan BcmNtwk_initPppSessions
BcmNtwk_initLan BcmNtwk_initPolicyRouting
BcmNtwk_initLan SUPPORT_RTPROXY
SIOCSIFADDR: No such device
SIOCSIFNETMASK: No such device
SIOCSIFBRDADDR: No such device
BcmNtwk_initLan CT_MIDDLEWARE
Passed 1 ... Passed 2
Flush Out Energy Accumulators completeboardHalInit6358: Initialization complete.
boardHalInit completed
Enter TaskCreate HRTBEAT
TaskCreate - spawn new task HRTBEAT
Exit TaskCreate
HEARTBEAT: Initialized!
bosMsgQCreate: Created message queue VRGEVQ at address 0x10002
Enter TaskCreate VRGEVPR
TaskCreate - spawn new task VRGEVPR
Exit TaskCreate
Enter TaskCreate HCAS
TaskCreate - spawn new task HCAS
Exit TaskCreate
*** gStartRxDesc = 0xA0E64000
*** gBufferSizeBytes = 1280
*** gStartTxDesc = 0xA0FEB000
hal6358PcmInit 261 nextTxDesc = 0xA0FEB000
hal6358PcmInit 261 nextTxDesc = 0xA0FEB008
hal6358PcmInit 265 Ownership for TX desc not set. Use this buffer.
PERF->IrqMask = 0xD8128624
PERF->IrqMask1= 0x00800000
Default value for provItemId '222' did not exist
ENDPT: hdspVhdOpen Secondary Connection VHD success. DSP 0, VHD (0x50) of type: 0x0
ENDPT: Setting T.38 error correction mode for vhd 80 to 0x104
ENDPT: hdspVhdOpen Secondary Connection VHD success. DSP 0, VHD (0x51) of type: 0x3
ENDPT: Setting T.38 error correction mode for vhd 81 to 0x104
dgasp: kerSysRegisterDyingGaspHandler: endpoint registered
cmMainTask: cvrgEndptGetNumEndpoints=1
cmMainTask: can only support 1 of 1 endpoints
ENDPT: EPTYPE_FXS
ENDPT 0 physId 0: EPTYPE_FXS
ENDPT: hdspVhdOpen Line VHD success. DSP 0, VHD (0x52) of type: 0x7
Switchboard ON (type Duplex): VHD 0x52/1 with VHD 0x0/0
Default value for provItemId '72' did not exist
Default value for provItemId '73' did not exist
Default value for provItemId '213' did not exist
Default value for provItemId '41' did not exist
Default value for provItemId '66' did not exist
Default value for provItemId '58' did not exist
Default value for provItemId '215' did not exist
ENDPT: Initialization completed successfully for endpt 0
ENDPT: DELETE CNX: endpt 0, cnx -1
cmAssociatePhysEndpt: Associating physEndpt 0 to cmEndpt 0
bosSocketSetInterface 168 ifno = 1
bosSocketSetInterface 216 status = 1
Line 0: Setting egress: 0, ingress: 0
00:00:53RTCP thread started with pid 794
br0: port 2(eth1.2) entering disabled state
br0: port 3(eth1.3) entering disabled state
br0: port 4(eth1.4) entering disabled state
br0: port 5(eth1.5) entering disabled state
硬件是bcm6359+5325e+spansion 16M bcm4318
接口 1WAN 4LAN 1FXS 1FXO 1USB
软件是电信定制版本，电信的用户名和密码 老大，我有一样的设备，现在没有一个好的CFE
能不能给俺发一份你的CFE过来？我现在用JTAG弄进去好安装kernel呀，谢谢
请email到
energymotor@gmail.com
谢谢 你把jtag给我接上，我就给你备份下来 呵呵，RG200E没有JTAG接口的。
页:
[1]