求助，刷了个别人提供的脱机固件，现在RG100A连不上了！
现在TTL信息如下CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: Thu May 10 22:28:34 CST 2007 (root@localhost.localdomain)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
*** Board is not initialized properly ***
Press:<enter> to use current value
'-' to go previous parameter
'.' to clear the current value
'x' to exit this command
96358VW2 ------- 0
96358VW ------- 1
96358GWVG ------- 2
96358MV2G ------- 3
96358M ------- 4
96358B ------- 5
96358BGWE_OEM1 ------- 6
96359PONG ------- 7
96358SV ------- 8
Board Id (0-8) :0
Number of MAC Addresses (1-32) :10
Base MAC Address :00:10:18:00:00:00
PSI Size (1-64) KBytes :24
Flash Block Size (1-128) in KBytes:64
Auxillary File System Size Percent:0
Main Thread Number :0
Flash Layout: Boot Kern
AuxFS Misc PSI
Flash RootFS Partition Length: 16384000
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x80528200 (1208832)
Initialized Data: 0x8041DA80 - 0x8041FA20 (8096)
BSS Area: 0x8041FA20 - 0x80426200 (26592)
Local Heap: 0x80426200 - 0x80526200 (1048576)
Stack Area: 0x80526200 - 0x80528200 (8192)
Text (code) segment: 0x80401000 - 0x8041DA80 (117376)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Use default boot line parameters: e=192.168.1.1:ffffff00 h=192.168.1.100 g= r=f
f=vmlinux i=bcm963xx_fs_kernel d=1 p=0
** Flash image not found. **
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-8) : 96358VW2
Number of MAC Addresses (1-32) : 10
Base MAC Address : 00:10:18:00:00:00
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 64
Auxillary File System Size Percent: 0
Main Thread Number : 0
web info: Waiting for connection on socket 0.
CFE>
CFE> ? ?? ?驙
FLASH是S2开头的，原本刷了openwrt，有一个商家无偿提供了个固件给我，我就直接CFE页面刷了，刷了以后就这样了，手动设置电脑IP为192.168.1.100，4个网口都试试了，PING192.168.1.1都不通，cfe页面也进不去，看来便宜不能贪啊！{{call{{ 有高手能从上面的信息看出什么问题吗？ 你刷的是带cfe的固件还是？ Number of MAC Addresses (1-32) :10改为12
Base MAC Address :00:10:18:00:00:00 看你机身背后的
Flash Block Size (1-128) in KBytes: 64 改为128
Auxillary File System Size Percent: 0 改为25
看看能不能进入cfe页面
还有的是flash是AM29LV320MT还是S29GL128 本帖最后由 cde12369875 于 2010-3-16 12:20 编辑
FLASH是S2开头的！CFE带不带我也不清楚哦，呵呵收到固件后就刷了，刷死后，问那个商家就没回应了，主要是我自己贪便宜了！
晕，现在连接超级终端正常显示，不过无法输入啊！按键盘都没反应，TTL信息和一楼的一样！是什么问题啊，好像baidu了啊，也没什么解决办法啊？ 用了新出的JTAG软件，信息如下
Probing bus ... Done
Instruction Length set to 5
CPU Chip ID: 00000110001101011000000101111111 (0635817F)
*** Found a Broadcom BCM6358 Rev 1 CPU chip ***
- EJTAG IMPCODE ....... : 11111111111111111111111111111110 (FFFFFFFE)
- EJTAG Version ....... : Unknown (7 is a reserved value)
- EJTAG DMA Support ... : No
- EJTAG Implementation flags: R3k DINTsup ASID_8 ASID_6 MIPS16 NoDMA MIPS32
Issuing Processor / Peripheral Reset ... Done
Enabling Memory Writes ... Skipped
Halting Processor ... <Processor Entered Debug Mode!> ... Done
Clearing Watchdog ...
这个是什么意思啊？用1.8a和C版的也是这样，是JTAg没接好？昨天刚焊接JTAG，不过CPU好像认出来了啊！ 晕，TTL线插在主板后面的USB接口，又能刷入命令了，谁能上个正常的RG100A的TTL信息吗？
页:
[1]