请问一下,这种情况还有啥解救方法.....谢谢.
自己顶一个...望大家指教...
我的也变砖了！不知会否也是这样！~
我的也刷挂了，不过我的可以看到CFE
不知道我这个能救么？
请高人指点
完整信息如下，不停地翻滚
按任意键停不下来
CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: Thu Feb 12 13:10:57 CST 2009 (root@localhost.localdomain)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320T, id 0x227a, size 16384KB
Flash Layout: Boot Kern
AuxFS Misc PSI
Flash RootFS Partition Length: 12320768
CFE using EMAC 0
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x805285D0 (1209808)
Initialized Data: 0x8041E210 - 0x8041FDF0 (7136)
BSS Area: 0x8041FDF0 - 0x804265D0 (26592)
Local Heap: 0x804265D0 - 0x805265D0 (1048576)
Stack Area: 0x805265D0 - 0x805285D0 (8192)
Text (code) segment: 0x80401000 - 0x8041E210 (119312)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.159
Gateway IP address :
Run from flash/host (f/h) : h
Default host run file name : 308nfs6358
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-2) : 96358VW2
Number of MAC Addresses (1-32) : 24
Base MAC Address : 00:1e:40:f5:3a:59
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from latest image (0xbe600000) ...
Code Address: 0x80010000, Entry Address: 0x80263018
Decompression OK!
Entry at 0x80263018
Closing network.
Starting program at 0x80263018
Linux version 2.6.8.1 (root@linuxserver) (gcc version 3.4.2) #1 Fri Feb 27 16:53:54 HKT 2009
Parallel flash device id 227a is not supported.
Readjusting rootfs partition to block 0 at offset 1107296256
*** Board is not initialized properly ***
prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 4000 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 29376k/32384k available (1948k kernel code, 2964k reserved, 427k data, 80k init, 0k highmem)
Calibrating delay loop... 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...unavailable.
NET: Registered protocol family 16
Computing partition layout for flash of size[-1] sectors[-1]
Flash not used for Auxillary File System
Partition ROOTFS_KRN Blks
SubPartition Image 1 Blks
SubPartition Image 2 Blks
Blk# BlkOff Blks BlkSize AvailSize MemStart MemLen Partition Name
0 1408 -1 -1 -1 0x00000580 1024 BOOTLOADER
-1 0 0 -1 -1 0x00000000 -1 ROOTFS_KRN
-1 0 0 0 0 0x00000000 0 JFFS_AUXFS
-1 0 0 -1 -1 0x00000000 -1 LOG_SCRPAD
-1 4294942719 0 -1 -1 0xffff9fff 24576 PERSISTMEM
No flash for scratch pad!
No flash for log sector!
Can't analyze prologue code at 801f59f4
SCSI subsystem initialized
usbcore: registered new driver hub
Skipping PCI bus scan due to resource conflict
TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca)
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v2.0
Failed to read image tag from flash
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbnet
brcmboard: brcm_board_init entry
ERROR - Invalid number of MAC addresses (1174405152) is configured.
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Cannot open root device "31:0" or unknown-block(31,0)
Please append a correct "root=" boot option
Kernel panic: VFS: Unable to mount root fs on unknown-block(31,0)
<0>Rebooting in 1 seconds..
现在最新状况
开机时按住Reset键可以进入CFE模式
然后连LAN4
可以登录192.168.1.1
随后用这个状态进入刷固件模式
谁知到刷了不带CFE的两个固件n次都不成功
继续尝试，刷入了个带CFE的
随后就惨了
现在成了这个状态：
CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: 2008-05-27 16:57:32 2 (tashin@linux-server1)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Parallel flash device id 227a is not supported.
*** Board is not initialized properly ***
Press:<enter> to use current value
'-' to go previous parameter
'.' to clear the current value
'x' to exit this command
96358VW2 ------- 0
96358VW ------- 1
96358GWVG ------- 2
96358MV2G ------- 3
96358M ------- 4
96358B ------- 5
96358BGWE_OEM1 ------- 6
96359PONG ------- 7
96358SV ------- 8
Board Id (0-8) :
但也是无法输入任何字符
Power和ADSL灯长亮红色，微弱的红色
是不是彻底没救了？
我的有一个，现在是加电反复重启，这种情况还能通过CFE升级好吗？哪位知道回一下，谢谢？
本帖最后由 天涯 于 2009-8-10 21:36 编辑
因为数据线在之前的情况下可以连接,并输入命令,而到此情况之下又无法输入了.真是有点怪喔,难道数据线的兼容性不好?
现在最新状况
开机时按住Reset键可以进入CFE模式
然后连LAN4
可以登录192.168.1.1
随后用这个状态进入刷固件模式
谁知到刷了不带CFE的两个固件n次都不成功
继续尝试，刷入了个带CFE的
随后就惨了
现在成了这 ...
kindlyer 发表于 2009-8-9 21:41 https://www.chinadsl.net/images/common/back.gif
ms CFE有问题，Flash MX29LV320T都不支持的，重新烧个新的CFE吧