H608bV1有天线版 突然变砖 高手分析下
具体变砖过程如下：在正常使用中，用FTP错误的在/lib目录下放了几个文件，发现后删掉了，但不记得是否全删了，是否删错了等等。然后就发现USB接口不能用了。
于是，在WEB页面选择了恢复出厂设置，然后就莫名其妙的变砖了。奇怪的是，power、run、dsl、lan等灯都是正常的闪的。PC上使用DHCP 会分配一个莫名奇妙的地址169.254.141.100，并且连接受限。PC上手动设置IP为192.168.1.3，也ping不通 192.168.1.1。
试过捅Reset键也不行，最后无奈只好上TTL看了下启动信息，在login部分就直接跳了过去，请高手分析一下原因，看看有没有修复的可能。
版本信息：
运营商: 中国电信
设备型号:ZXV10 H608B
设备标识号: 002293-3220000229323FF92
硬件版本:V1.1.00
软件版本:V1.1.02T13_E
TTL线连接后终端的启动信息：
ZXV10 HGW bootloader V1.9
SDRAM size = 0x2000000-------->
Hardware version is 1-------->
Processor clock speed 264.0MHz
FLASH size = 0x1000000-------->
Finding flashfs partition ...@ offset 00540000
Finding flashfs partition ...@ offset 00620000
2 partition found
Boot from image B @ offset 00620000
done.
Image 'image' is a Linux kernel
Trying to load initrd...none found
Calling Configure_NVS_FromFile.
LZMA 4.05
00rsion 2.6.11.12 (xia@localhost.localdomain) (gcc version 4.0.1) #137 Tue Dec 23 09:03:46 CST 2008
CPU: ARM1026EJ-Sid(wb)B revision 2 (ARMv5TEJ)
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets
Machine: Solos CX46xx, unknown variant
!!!!!!!
the hw id is 1,
!!!!!!Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists
Kernel command line: console=ttyS0 root=31:4 rw mem=31M mtdparts=phys_mapped_flash:256k(boot),1024k(kernel),4992k(JFFS2),1024k(k2),4992k(J2),-(CT) rootfstype=jffs2
init_dma not supported
PID hash table entries: 128 (order: 7, 2048 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 31MB = 31MB total
Memory: 28980KB available (1959K code, 379K data, 76K init)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new driver hub
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
Ledkey Driver Version 0.0.1.
ledkey : ===== ledkey_init =====
init watchdog!!!
zteinfo_init
Solos on-chip UART init.
ttyS0 at I/O 0x0 (irq = 29) is a Solos UART
io scheduler noop registered
RTL18305SD: Registered new driver
PPP generic driver version 2.4.2
NET: Registered protocol family 24
physmap flash device: 1000000 at 38000000
phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
phys_mapped_flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 8 MTD partitions on "phys_mapped_flash":
0x00000000-0x01000000 : "flash"
0x00000000-0x00020000 : "Bootloader"
0x00020000-0x00040000 : "config"
0x00540000-0x00620000 : "kernel"
0x00040000-0x00540000 : "filesystem"
0x00620000-0x00700000 : "kernel2"
0x00700000-0x00c00000 : "filesystem2"
0x00c00000-0x01000000 : "ct-jffs2"
Solos-W EHCI starting up...
solosW-ehci usb00: Solos USB 2.0
solosW-ehci usb00: irq 9, pci mem ff800100
solosW-ehci usb00: new USB bus registered, assigned bus number 1
wlan short push
solosW-ehci usb00: park 0
solosW-ehci usb00: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
usb usb1: Product: Solos USB 2.0
usb usb1: Manufacturer: Linux 2.6.11.12 ehci_hcd
usb usb1: SerialNumber: Solos EHCI
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
INTR_MASK 37, 37
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
u32 classifier
OLD policer on
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
IPv4 over IPv4 tunneling driver
ip_conntrack version 2.1 (248 buckets, 1984 max) - 320 bytes per conntrack
usb 1-1: new high speed USB device using solosW-ehci and address 2
usb 1-1: Product: USB2.0 FlashDisk
usb 1-1: Manufacturer: Kingmax
ip_tables: (C) 2000-2002 Netfilter core team
usb 1-1: SerialNumber: 20080125000000000000018C
scsi0 : SCSI emulation for USB Mass Storage devices
ip_conntrack_rtsp v0.01 loading
ip_nat_rtsp v0.01 loading
netfilter PSD loaded - (c) astaro AG
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Please set the MAC Address for the WAN Bridge.
Set the Environment variable 'wan_br_mac'.
MAC Address should be in the following format: xx.xx.xx.xx.xx.xx
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 76K
Vendor: Kingmax Model: USB2.0 FlashDiskRev: 1.00
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 31875072 512-byte hdwr sectors (16320 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
SCSI device sda: 31875072 512-byte hdwr sectors (16320 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
sda: sda1
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
init started:BusyBox v1.01 (2008.12.23-01:06+0000) multi-call binary
Starting pid 146, console /dev/ttyS0: '/etc/rc'
Alarm clock
Loading Conexant BSP...
Using /lib/modules/2.6.11.12/kernel/drivers/net/arm/solos_ethernet.ko
solos_ethernet: module license 'unspecified' taints kernel.
rtl8306sd_hw_init
rtl8306_switch_init
rtl8306_initsucess!
rtl8306_initQossucess!
rtl8306_setCPUPortsucess!
rtl8306_initVlansucess!
rtl8306 IGMP snooping enabled!
rtl8306sd_hw_init
rtl8306sd_hw_init
rtl8306sd_hw_init
rtl8306sd_hw_init
rtl8306sd_hw_init
rtl8306sd_hw_init
solos_eth_mii: probed
Using /lib/hsl_mod_gpl.o
Using /lib/cnxt_fiq.o
Using /lib/cnxt_drv.o
BASE MAC ADDRESS 00:11:22:33:44:55
Starting Conexant drivers
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Quantum v1.01
wlan long push
msc16 loaded
'create dev file with mknod /dev/adet_char c 244 0'.
msc16_load_file returned 0
sram_buffer : 0xffa00258 addr : 0x70000258
Passing command buffer 70000258 to MSC16
Conexant drivers started
starting task turbo_WhipTask
DSL MSC16 imem 4096, dmem 2048
DSL MSC16 version 1.3
Using /lib/wlan_wsc.ko
Using /lib/modules/2.6.11.12/kerRUNNING Timer started
nel/arch/arm/mach-solos/solosw_defaultrestore.ko
enable virtual port
value is 20001
value is 30002
value is 40004
value is 50008
Loading Wireless ...
chip_id = 1
1
Reading True PDA ...
---dsl is off--
Using /lib/stun_ahb.ko
DRIVER VERSION: 3.0
---dsl is off--
sm_drv_traffice_init called
Received the MAC Address trap
Waiting for message from kernel
init_mac(): 0:22:93:23:ff:92
SIOCGIFFLAGS: No such device
received link state trap
SIOCSIFHWADDR: No such device
SIOCGIFFLAGS: No such device
in atm_dev_register, acQosAdslName bunatm
Starting pid 274, console /dev/ttyS0: '/sbin/geeth0: port 0 link up (100/Full)
---dsl is off--
ZXV10-H608B login: @@@@ No config file!
read_config_file fail=-1, recovery default config!
recovery critical and lable param
extract_env_cfg_bin envhdr->magic = ENVZ
extract_env_cfg_binclen uncompress after = 816 bytes
env used: 816 bytes
env free: 261328 bytes
env total : 262144 bytes
compress_env_cfg_binzipsize compress = 293 bytes
@@@@ No config file!
Read '/etc/board.conf' failed, syntax error -1 at line -1!
(0x10305) module Enter into qt_register
(0x10306) module Enter into qr_rule_register
(0x10309) module Enter into qr_type_register
(0x10307) module Enter into qa_register
(0x10308) module Enter into qq_register
MSG(0x003) module proc_msg_init
extract_env_cfg_bin envhdr->magic = ENVZ
extract_env_cfg_binclen uncompress after = 816 bytes
envdb-enable = 1
CORE(0x007) module clear wan module 1705 table row is:0
CORE(0x007) module clear wan module 1706 table row is:0
CORE(0x007) module clear wan module 1704 table row is:0
CORE(0x007) module clear wan module 1708 table row is:0
CORE(0x007) module clear wan module 1714 table row is:0
print_all start
env used: 816 bytes
env free: 261328 bytes
env total : 262144 bytes
print_all end
can`t find m:security i:700 r: 0 n:password v:admin
can`t find m:security i:700 r: 0 n:username v:admin
can`t find m:security i:700 r: 0 n:enable v:1
can`t find m:security i:710 r: 0 n:enable v:0
can`t find m:syspara i:4004 r: 0 n:URL v:http:///ACS
can`t find m:syspara i:4004 r: 0 n:Username v:
can`t find m:syspara i:4004 r: 0 n:Password v:
can`t find m:syspara i:4004 r: 0 n:ConnectionRequestUsername v:
can`t find m:syspara i:4004 r: 0 n:ConnectionRequestPassword v:
can`t find m:syspara i:4004 r: 0 n:PeriodicInformEnable v:0
can`t find m:syspara i:4004 r: 0 n:PeriodicInformInterval v:43200
can`t find m:syspara i:4004 r: 0 n:PeriodicInformTime v:0000-00-00T00:00:00
can`t find m:syspara i:4004 r: 0 n:Tr069Enable v:0
can`t find m:syspara i:4004 r: 0 n:MiddlewareURL v:255.255.255.255:0
can`t find m:syspara i:4020 r: 0 n:BOOTSTRAP v:1
can`t find m:syspara i:4020 r: 0 n:ssl_auth v:0
can`t find m:wan i:1711 r: 0 n:areacode v:AnHui1
continue: writeFlashForOther don't sys lable param
Failed to read 22!
Failed to read 23!
Failed to read 24!
continue: writeFlashForWLANKEYID don't sys lable param
Failed to read 32!
Failed to read 33!
Failed to read 34!
Failed to read 41!
continue: writeFlashForOther don't sys lable param
Failed to read 43!
Failed to read 51!
__no node:key_para_get.para_val=lfjpn,name = password
Failed to read 53!
Failed to read 61!
Failed to read 62!
sys lable param is NULL, write_default_value set default param,name = password, value = useradmin
DEVINFO(0x101) module Save critical param...
CORE(0x007) module add_first_class_param start
CORE(0x007) module add_first_class_param end
CORE(0x007) module delete_second_class_param start
CORE(0x007) module delete_second_class_param end
CORE(0x007) module add_second_class_param start
CORE(0x007) module add_second_class_param end
env used: 816 bytes
env free: 261328 bytes
env total : 262144 bytes
compress_env_cfg_binzipsize compress = 292 bytes
DEVINFO(0x101) module Save...
error:sys lable param ,config is not exist!!!
continue: writeFlashForOther don't sys lable param
Failed to read 22!
Failed to read 23!
Failed to read 24!
continue: writeFlashForWLANKEYID don't sys lable param
Failed to read 32!
Failed to read 33!
Failed to read 34!
Failed to read 41!
continue: writeFlashForOther don't sys lable param
Failed to read 43!
Failed to read 51!
__no node:key_para_get.para_val=lfjpn,name = password
Failed to read 53!
Failed to read 61!
Failed to read 62!
sys lable param is NULL, write_default_value set default param,name = password, value = useradmin
DEVINFO(0x101) module Save critical param...
extract_env_cfg_bin envhdr->magic = ENVZ
extract_env_cfg_binclen uncompress after = 816 bytes
CORE(0x007) module add_first_class_param start
CORE(0x007) module add_first_class_param end
CORE(0x007) module delete_second_class_param start
CORE(0x007) module delete_second_class_param end
CORE(0x007) module add_second_class_param start
CORE(0x007) module add_second_class_param end
env used: 816 bytes
env free: 261328 bytes
env total : 262144 bytes
compress_env_cfg_binzipsize compress = 291 bytes
DEVINFO(0x101) module Save...
!!!error:sys lable param ,lable param is not exist!!!
continue: writeFlashForOther don't sys lable param
Failed to read 22!
Failed to read 23!
Failed to read 24!
continue: writeFlashForWLANKEYID don't sys lable param
Failed to read 32!
Failed to read 33!
Failed to read 34!
Failed to read 41!
continue: writeFlashForOther don't sys lable param
Failed to read 43!
Failed to read 51!
__no node:key_para_get.para_val=lfjpn,name = password
Failed to read 53!
Failed to read 61!
Failed to read 62!
sys lable param is NULL, write_default_value set default param,name = password, value = useradmin
DEVINFO(0x101) module Save critical param...
extract_env_cfg_bin envhdr->magic = ENVZ
extract_env_cfg_binclen uncompress after = 816 bytes
CORE(0x007) module add_first_class_param start
CORE(0x007) module add_first_class_param end
CORE(0x007) module delete_second_class_param start
CORE(0x007) module delete_second_class_param end
CORE(0x007) module add_second_class_param start
CORE(0x007) module add_second_class_param end
env used: 816 bytes
env free: 261328 bytes
env total : 262144 bytes
compress_env_cfg_binzipsize compress = 292 bytes
DEVINFO(0x101) module Save...
DSL(0x20211) module InitTrainMode strTemp = |N/A| !!!
DSL(0x20211) module InitTrainMode value = |N/A| !!!
DSL(0x20211) module DSL_TRAINMODE Add Item!!
DSL(0x20211) module InitTrainMode mode = |ff| !!!
DSL(0x20211) module InitTrainMode mode = |ff| !!!
DSL(0x20211) module InitTrainMode mode = |ff| !!!
echo "PSa1:AnnexACapability:AnnexA/T1413" > /proc/quantum/drv_ctl
echo "PSa1:BisACapability:A2/A2+" > /proc/quantum/drv_ctl
echo "PSa1:BisMCapability:Disable" > /proc/quantum/drv_ctl
ct_jffs2 exist!
=========== mount ct_jffs ===========
No need to syn version!
---dsl is off--
LOG(0x103) module set_apply_conf:syslogd process not run
LOG(0x103) module control_syslogd:success to start syslogd 308
LOG(0x103) module control_klogd:success to start klogd 309
one second = 100 tick
BRIDGE(0x40224) module cant add CONF_ID_BRIDGE_MM
syslogd:StarupTime:39
syslog:AutoSave:0,SaveIntrvl:7200,FileSize:102400,HbInterval:72000 顺便说一下，猫是淘宝上买的，提醒我去找电信换的朋友们，谢谢你们了。 我手上有个608V1的猫，你付来回邮费我给你换~然后我再退回给电信，呵呵 路过进来看看 我手上有个608V1的猫，你付来回邮费我给你换~然后我再退回给电信，呵呵
redcom 发表于 2009-7-25 20:26 https://www.chinadsl.net/images/common/back.gif
这是什么精神阿，国际人道主义精神阿！你太伟大了，回头给你发站内信。
页:
[1]