呵呵，8楼朋友把我之前出售的信息也贴出来了啊。。
白绿蓝，直接顺着从面相灯最下面的一根针开始插，最上面的留空。。
唉 不知道是不是我的PL2303线不能用，还是我的DB120-WG根本就是没救了，或者是我水平有限、操作有误
反正，今晚的尝试是失败了
谢谢楼上的各位
改天我去淘宝买根PL2303线回来，再试一次，不行就只能扔掉这个砖块了
哇，这以多高手都进来啦！
呵，我的线明天到了，不知道刷哪个固件。
有大侠有好的建议帮我回复下
本帖最后由 yusheng2008 于 2009-7-20 18:31 编辑
我的猫和你一模一样。也是在淘宝买了ttl线，靠近显示灯这边算起是GND、TX、RX、VCC。我接好了能显示如下信息：
|
CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: 二1月 29 07:41:15 CST 2008 (root@ZTJ)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot Kern
AuxFS Misc PSI
Flash RootFS Partition Length: 12320768
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x805285A0 (1209760)
Initialized Data: 0x8041DD30 - 0x8041FDC0 (8336)
BSS Area: 0x8041FDC0 - 0x804265A0 (26592)
Local Heap: 0x804265A0 - 0x805265A0 (1048576)
Stack Area: 0x805265A0 - 0x805285A0 (8192)
Text (code) segment: 0x80401000 - 0x8041DD30 (118064)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.159
Gateway IP address :
Run from flash/host (f/h) : h
Default host run file name : 308nfs6358
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-9) : 96358VW2
Number of MAC Addresses (1-32) : 24
Base MAC Address : 00:1e:40:9c:e2:e2
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
这里猛按键盘都没有反应！
然后路由猫启动一直走到最后不动了，也不能输入。
device eth1.3 entered promiscuous mode
br0: port 3(eth1.3) entering learning state
br0: topology change detected, propagating
br0: port 3(eth1.3) entering forwarding state
device eth1.4 entered promiscuous mode
br0: port 4(eth1.4) entering learning state
br0: topology change detected, propagating
br0: port 4(eth1.4) entering forwarding state
device wl0.1 entered promiscuous mode
br0: port 5(wl0.1) entering learning state
br0: topology change detected, propagating
br0: port 5(wl0.1) entering forwarding state
device wl0.2 entered promiscuous mode
br0: port 6(wl0.2) entering learning state
br0: topology change detected, propagating
br0: port 6(wl0.2) entering forwarding state
device wl0.3 entered promiscuous mode
br0: port 7(wl0.3) entering learning state
br0: topology change detected, propagating
br0: port 7(wl0.3) entering forwarding state
device wl0 entered promiscuous mode
br0: port 8(wl0) entering learning state
br0: topology change detected, propagating
br0: port 8(wl0) entering forwarding state
HTB init, kernel part version 3.17
Action 4 device ifb0 ifindex 2
tcf_action_init_1: successfull mirred
br0: port 2(eth1.2) entering disabled state
br0: port 3(eth1.3) entering disabled state
br0: port 4(eth1.4) entering disabled state
br0: port 1(usb0) entering disabled state
就是进不了CFE状态。
键盘输入无效？我用xp的超级终端和SecureCRT都试过，不行。为啥？
如果按键没有能停止,就试着交换一下TX、RX接线.
如果按键没有能停止,就试着交换一下TX、RX接线.
天涯 发表于 2009-7-20 18:35 https://www.chinadsl.net/images/common/back.gif
不行。交换了连显示都没有了。
我也按照帖子介绍把 流控制 下面的 钩（rst/cst）全部去掉了。
更换笔记本上操作，问题解决。进入成功。原因不明。
怀疑我的台式机主板有问题。。。
学习啦~~~~~~
按照靠近显示灯这边算起是GND、TX、RX、VCC是正确的，成功将砖变成路由！谢谢啦
收藏备用，接下来开刷