教你把BCM6358硬超到400MHZ
教你把BCM6358硬超到400MHZ这个很简单。焊几个电阻就搞定了。。我测试了下还好。快多了。。没有死过机。不过
你得装散热哟
以下方法只适用于DB120-WG（我没有其它设备的硬件。无法确定位置。如果有朋友可以把你们手上的板借给我二天我就可以确定其它型号的BCM6358主板超频位置）
把R206，R207，R208，R209都焊一个4.7K的电阻就OK了。简单吧
看我超频后的图。呵呵。。。。
我先自已DING一下。呵呵。。。。 上pcb上的图看看 dyscc大侠又发高文造福大众了 顶！ 只找到R207的位置.R206.R208.R209在哪?可以上个图标明吗. 问题是干什么快多了？？我是菜鸟！ 5# sxj1234
R207 R208 R209位于BCM4318下面不远处。大约有8个电阻是空焊的地方。仔细找找 本帖最后由 sxj1234 于 2009-7-7 00:26 编辑
找到了,谢谢.照着你讲的方法把BCM6358硬超到400MHZ
,启动到一半卡住了,咋办?
启发信息:
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot Kern
AuxFS Misc PSI
Flash RootFS Partition Length: 12058624
CPU type 0x2A010: 399MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 67108864 bytes (64MB)
Total memory used by CFE:0x80401000 - 0x80529860 (1214560)
Initialized Data: 0x8041E740 - 0x80421060 (10528)
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-8) : 96358VW2
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:1e:40:00:00:00
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number : 0
udp_send finished
No answer .auto boot ...
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from latest image (0xbe5e0000) ...
Code Address: 0x80010000, Entry Address: 0x80257018
Decompression OK!
Entry at 0x80257018
Closing network.
Starting program at 0x80257018
Linux version 2.6.8.1 (root@liangbingtong) (gcc version 3.4.2) #1 Thu Apr 17 19:
47:37 CST 2008
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
fInfo.flash_rootfs_available_length = 16252928
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 03fa0000 @ 00000000 (usable)
On node 0 totalpages: 16288
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 12192 pages, LIFO batch:2
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 256 (order 8: 2048 bytes)
Using 200.000 MHz high precision timer.
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 61864k/65152k available (1902k kernel code, 3220k reserved, 425k data, 7
6k init, 0k highmem)
Calibrating delay loop... 399.76 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...unavailable.
NET: Registered protocol family 16
Total Flash size: 16384K with 128 sectors
Computing partition layout for flash of size sectors
Flash split 25% into RootFS+Kernel : AuxFS
Partition ROOTFS_KRN Blks[ 92: 1 ..92]
SubPartition Image 1 Blks[ 46: 1 ..46]
SubPartition Image 2 Blks[ 46:47 ..92]
Blk# BlkOff Blks BlkSize AvailSize MemStart MemLen Partition Name
0 1408 1131072 131072 0xbe000580 1024 BOOTLOADER
1 0 9213107212058624 0xbe020000 12058624 ROOTFS_KRN
93 0 32131072 4194304 0xbeba0000 4194304 JFFS_AUXFS
125 0 1131072 131072 0xbefa0000 131072 LOG_SCRPAD
126 106496 1131072 131072 0xbefda000 24576 TW_PERSISTMEM
127 106496 1131072 131072 0xbeffa000 24576 PERSISTMEM
Can't analyze prologue code at 801ea324
SCSI subsystem initialized
usbcore: registered new driver hub
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v2.0
File system address: 0xbe5e0100
Registered device mtd dev Flash
Registered device mtd dev Flash
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0050300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0052400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x3 is enabled
WIFI: Button Interrupt 0x0 is enabled
WIFI: map_external_irq begin
SES: LED GPIO 0x8018 is enabled
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
initLed: led: mask=0x400000, state=0
initLed: led: mask=0x0100, state=0
initLed: led: mask=0x1000000, state=0
initLed: led: mask=0x0001, state=0
initLed: led: mask=0x0004, state=0
initLed: led: mask=0x0010, state=0
initLed: led: mask=0x0002, state=0
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
u32 classifier
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 76k freed
init started:BusyBox v1.00 (2008.04.17-11:53+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
BusyBox v1.00 (2008.04.17-11:53+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Apr 17 2008 19:45:36
Config Ethernet Switch Through MDIO Pseudo PHY Interface
dgasp: kerSysRegisterDyingGaspHandler: eth0 registered
eth0: MAC Address: 00:1E:40:00:00:01
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 00:1E:40:00:00:02
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.150.10.15.cpe2.2
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
BcmCfg_recover, L341: Waiting Usb init complete
cfminit.c, L358: flgfoundusb:0
cfminit.c, L379: flgfounddisk:0
cfminit.c, L445: time:1 sec
##no usb device22
SIGUSR1
# 是不是6358的个体体制问题跟PC的cpu那样 超频后电压没喂饱开机进不了系统...? 我只设置了挢接.无线没开.去掉了usb
的两个发光二极管.
是不是硬改后要重刷一遍固件.