**hg522用数据线连接怎么登入系统修改
setwmestrcnxt : Set WME ACK strategy status(0 = ack , 1 = no ack, 2 = dynamic).
statusset or get BSS enabled status: up/down.
statusset or get BSS enabled status: up/down.
statusset or get BSS enabled status: up/down.
WIRELESS is on
SIOCGIFFLAGS: Unknown error 19
SIOCGIFFLAGS: Unknown error 19
SIOCGIFFLAGS: Unknown error 19
file open failed, trying default file.
Let's go boy... :p
[*] Get ethernetflags....
[*] Eth header is ready....
[*] Arp header is ready....
Let's go boy... :p
[*] Get ethernetflags....
[*] Eth header is ready....
[*] Arp header is ready....
device eth0 is not a slave of br0
Connction id is 1
acCmd : echo "L:vpi=8/vci=35/rfc1483=true/rfc1483.mode=Llcbridged/class=ubr/port
=a1" > /proc/quantum/drv_ctl
acCmd : echo "V:vpi=8:vci=35:conid=1" > /proc/quantum/drv_ctl
Call the function for bunif interface
Starting OAM test
Starting OAM test
Connction id is 4
acCmd : echo "L:vpi=8/vci=35/rfc1483=true/rfc1483.mode=Llcbridged/class=ubr/port
=a1" > /proc/quantum/drv_ctl
acCmd : echo "V:vpi=8:vci=35:conid=4" > /proc/quantum/drv_ctl
Call the function for bunif interface
Error: an inet address is expected rather than "dev".
Error: an inet address is expected rather than "dev".
Error: an inet address is expected rather than "dev".
Error: an inet address is expected rather than "dev".
Error: an inet address is expected rather than "dev".
Error: an inet address is expected rather than "dev".
Error: an inet address is expected rather than "dev".
paed: w 0-China netlink_coPrivacy invoked is NOT set because open system enabl
ed
paed: w wpanone_inNo IV counter file available, starting from zero
wpa_supplicant: applet not found
Got interface ifname wl0
WIRELESS is on
string = setoid wl0 10000002ssid ChinaQos-Com
RSSID :ssid set done ChinaQos-Com
DEVICE PIN: 35420736
pppc -I ppp_8_35_2 connecting...
===bUsbconf=0====!
Error: an inet prefix is expected rather than "table".
Error: an inet address is expected rather than "dev".
FILE Iswanmonitor.c, LINE is349 result is1
FILE Iswanmonitor.c, LINE is349 result is1
WAN Not Found
1970-1-1 0:0:49 Notice 104508 DSL成功激活!
paed: w 0-China netlink_coPrivacy invoked is NOT set because open system enabl
ed
pppc -I ppp_8_35_2 113.232.142.110 connected.
wpa_supplicant: applet not found
FILE Iswanmonitor.c, LINE is349 result is1
FILE Iswanmonitor.c, LINE is349 result is1
RTNETLINK answers: Unknown error 3
RTNETLINK answers: Unknown error 3
RTNETLINK answers: Unknown error 3
RTNETLINK answers: Unknown error 3
RTNETLINK answers: Unknown error 3
RTNETLINK answers: Unknown error 3
RTNETLINK answers: Unknown error 3
v0.06 PLL w ln p08 zi
Solos 461x PP boot v1.5
SDRAM size = 0x2000000
Processor clock speed 264.0MHz
--- Check Tag CRC success,System Type: DUAL.
Start up info: 在线等{{gangzai13{{ 本帖最后由 lph1216 于 2009-7-5 20:42 编辑
我也想知道。。。
TTL进入后，输入用户名：!!Huawei 密码@HuaweiHgw
显示提示符为“ATP>”，输入“start”后，提示符变为“#”。。。
输入“ls”查看目录。。。，后面就不懂怎么搞了。。。。
此状态无法输入信息 是不是数据线问题 多半是数据线的问题，检查一下接地线是否正确 不是数据线问题
现在用的里面的putty这个软件用ctrl+c的方法可以看到井号提示符
（未使用密码）
不知道下面怎么进行 本帖最后由 yunyiying 于 2009-7-6 12:57 编辑
1# 古梁
start变成#号后：
cd var
然后有两种方法：
方法1
vi curcfg.xml(如果你对VI比较熟可以直接在这里打开这个文件就能在里面找到超级用户的密码了)
方法：弄个U盘插上，输入
cp curcfg.xml /mnt/usb1_1
把这个文件复制到U盘，然后到电脑上打开它也能在里面找到超级用户和密码。然后就不需要数据线了，用超级用户登陆以后基本所有的配置都可以修改了。 本帖最后由 古梁 于 2009-7-6 05:23 编辑
现在恢复了原来e8的配置文件，是东大的配置文件里没那个密码
现在可以登陆了。关键是把mtdblock3文件考到U盘修改在回传就会ok
可惜我不懂linux系统，，请提供些命令
用下面i这段命令U盘放电脑上没文件
cat /dev/mtd3> /mnt/usb1_4/mtd2
自己乱搞了一气U盘出现了几个mtd2的0字节文件 9# 古梁
HG522应该也有导入配置文件的功能吧？我的HG527是有的。http://192.168.1.1/download/configfile.conf 超级用户登陆后，配置文件下回来，修改后再用导入配置文件的功能把修改后的配置文件导入进去应该就OK了。
俺的HG527就是用这种方法开的telnet，并把user用户也提成超级用户了。