中兴 H101 网关 求助
入手一中兴 H101 网关 带VOIP、蓝牙、无线、路由现在只能当ap和交换机用
连无线和有线都能分配ip
ping路由能ping通 telnet和ftp都可以
就是不能进路由管理界面 本帖最后由 kuanxiao 于 2009-6-14 21:42 编辑
启动过程
H100 boot v3.10 for board3.0 2.0( add watchDog ) 2005-7-16 11:19
Please use version: h100ver (or h100vmlinuz.bin h100jffs.img )
h100_deviceId == 0x0017
to read Wlan key,if on,to recovery
ADI Linux Kernel (Version: 2.4.16 - 20040713) (Build #0)...version 1Looks Ok
Please select a system to boot. If you do not before the timer
expires, the default selection will be used. A "*" indicates
the default selection.
1. ZTE Recovery
2. ZTE Linux Kernel...
.....Using default system...
Preparing ADI Linux Kernel (Version: 2.4.16 - 20040713) (Build #0)..............
.
Starting Kernel 1 ...
Number of Clks = ffffffff
Adding 32 MB RAM and 8 MB Flash
Loading LX4189 MMU routines.
CPU revision is: 0000c401
Primary instruction cache 16kb, linesize 32 bytes
Primary data cache 16kb, linesize 32 bytes
Linux version 2.4.18 (root@XLVersion) (gcc version 3.3.4) #22 Sat Feb 25 10:44:0
5 CST 2006
System clock is 100 MHz
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
memory: 00800000 @ 1f800000 (ROM data)
On node 0 totalpages: 8192
zone(0): 4096 pages.
zone(1): 4096 pages.
zone(2): 0 pages.
Kernel command line: auto debug rw root=/dev/mtdblock4
Initializing AD6843 Interrupt Controller, Revision 4.0
On node 0 totalpages: 8192
zone(0): 4096 pages.
zone(1): 4096 pages.
zone(2): 0 pages.
Kernel command line: auto debug rw root=/dev/mtdblock4
Initializing AD6843 Interrupt Controller, Revision 4.0
Timers are getting initalized
Timers are getting initalized
Calibrating delay loop... 199.47 BogoMIPS
Memory: 28732k/32768k available (2006k kernel code, 4036k reserved, 113k data, 6
4k init)
Dentry-cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode-cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Checking for 'wait' instruction...unavailable.
POSIX conformance testing by UNIFIX
Press ESC to enter manufacture test in 2 seconds .....
VENDOR ID = 1106 DEVICE ID 3038IRQ 4
PCI: I/O region #5:20@20 for device 00:02.1
VENDOR ID = 1106 DEVICE ID 3104IRQ 4
PCI: mem region #1:100@1a010000 for device 00:02.2
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
event logger registeration successpty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI en
abled
ttyS00 at 0xb9020000x (irq = 1) is a 16450
ttyS01 at 0xb90a0000x (irq = 2) is a 16450
ADSL Link Tracker Module Initialized
block: 64 slots per queue, batch=16
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
sierra_probe is called 11111
Init_ether: is called
phEthPortis 00000000,
phEthPortis 810cf400,
sierra_probe is called 11111
Init_ether: is called
phEthPortis 00000000,
phEthPortis 811bf800,
Added AP PREROUTE Hook
Added AP POSTROUTE Hook Initialize EMACMON !!!
Start EMACMON!!!
!!!!!initDataAPATM OK!!!!!
initADSLInterface():is called!!
PPP generic driver version 2.4.1
!!!!flashSize = 8 MB!!!!
AD6843 Residential Gateway flash probe(0x1f800000,8388608,2): 800000 at 1f800000
Found: INTEL TE28f640j3
0x002 gen_probe.c
0: offset=0x0,size=0x20000,blocks=64
tjg add Using word write method
tjg set cfi_intelext_write_buffers !!!!!!!!!!!!!!!!!!!!!1
Creating 5 MTD partitions on "Analog Devices AD6843 Residential Gateway":
0x00000000-0x00004000 : "Bootstrap 1"
0x00004000-0x00008000 : "Configuration"
0x00008000-0x00020000 : "Bootstrap 2"
0x00020000-0x00100000 : "Kernel"
0x00100000-0x007e0000 : "Root"
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
IPv4 over IPv4 tunneling driver
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack_pptp version 1.9 loaded
ip_nat_pptp version 1.5 loaded
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack_rtsp v0.01 loading
ip_nat_rtsp v0.01 loading
netfilter PSD loaded - (c) astaro AG
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
FAT: bogus logical sector size 6552
jffs2_scan_inode_node(): CRC failed on node at 0x00003c9c: Read 0x00001ae2, calc
ulated 0x03299aab
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00003ca4: 0x504b in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00003cb8: 0x0004 in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00003cbc: 0x43ff in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00003cc0: 0x43ff in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00003cc4: 0x43ff in
stead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00003cc8: 0x0002 in
stead
split old frag 0x0000-0xc2000 -->hole
split old frag 0x43000-0xc2000 -->hole
split old frag 0x54000-0xc2000 -->hole
split old frag 0x0000-0x41000 -->hole
split old frag 0x4000-0x3f000 -->hole
split old frag 0xa1000-0xc2000 -->hole
split old frag 0xa1000-0xbe000 -->hole
split old frag 0x4000-0x31000 -->hole
split old frag 0x4000-0x1e000 -->hole
split old frag 0x4000-0x12000 -->hole
split old frag 0xb5000-0xbe000 -->hole
split old frag 0x62000-0x7d000 -->hole
split old frag 0x8000-0x2d000 -->hole
split old frag 0x8000-0xc000 -->hole
split old frag 0xf000-0x2d000 -->hole
split old frag 0xf000-0x28000 -->hole
split old frag 0x15000-0x28000 -->hole
split old frag 0x15000-0x22000 -->hole
split old frag 0x0000-0x34000 -->hole
split old frag 0x2b000-0x34000 -->hole
split old frag 0x14000-0x2a000 -->hole
split old frag 0x35000-0x4b000 -->hole
split old frag 0x43000-0x4b000 -->hole
split old frag 0x24000-0x2a000 -->hole
split old frag 0x0000-0x6000 -->hole
split old frag 0x0000-0x32000 -->hole
split old frag 0x3000-0x32000 -->hole
split old frag 0x16000-0x32000 -->hole
split old frag 0x22000-0x32000 -->hole
split old frag 0x5000-0x15000 -->hole
split old frag 0x5000-0x11000 -->hole
split old frag 0x2a000-0x32000 -->hole
split old frag 0x6000-0xe000 -->hole
split old frag 0x1a000-0x1f000 -->hole
split old frag 0xb000-0x16000 -->hole
split old frag 0xb000-0x14000 -->hole
split old frag 0x18000-0x48000 -->hole
split old frag 0x30000-0x48000 -->hole
split old frag 0x30000-0x3f000 -->hole
split old frag 0x30000-0x36000 -->hole
split old frag 0x0000-0x8000 -->hole
split old frag 0x1b000-0x2b000 -->hole
split old frag 0x24000-0x2b000 -->hole
split old frag 0x0000-0x1a000 -->hole
split old frag 0xb000-0x1a000 -->hole
split old frag 0x1000-0xa000 -->hole
split old frag 0x1b000-0x22000 -->hole
split old frag 0x1b000-0x20000 -->hole
split old frag 0x33000-0x3b000 -->hole
split old frag 0x5000-0xa000 -->hole
split old frag 0x7000-0x42000 -->hole
split old frag 0x7000-0x1d000 -->hole
split old frag 0x1f000-0x42000 -->hole
split old frag 0xa000-0x1d000 -->hole
split old frag 0x49000-0x63000 -->hole
split old frag 0x0000-0xb000 -->hole
split old frag 0x0000-0x4000 -->hole
split old frag 0x0000-0x3000 -->hole
split old frag 0x140000-0x255000 -->hole
split old frag 0x140000-0x1b3000 -->hole
split old frag 0x7000-0xdd000 -->hole
split old frag 0x18000-0xdd000 -->hole
split old frag 0x1d8000-0x255000 -->hole
split old frag 0x46000-0xdd000 -->hole
split old frag 0x18000-0x3d000 -->hole
split old frag 0x46000-0xd4000 -->hole
split old frag 0x1d8000-0x21f000 -->hole
split old frag 0x232000-0x255000 -->hole
split old frag 0x46000-0xd0000 -->hole
split old frag 0x61000-0xd0000 -->hole
split old frag 0x19d000-0x1b3000 -->hole
split old frag 0x232000-0x252000 -->hole
split old frag 0x62000-0xaf000 -->hole
split old frag 0x62000-0x9a000 -->hole
split old frag 0x0000-0x2a000 -->hole
split old frag 0x0000-0x13000 -->hole
split old frag 0x19000-0x5b000 -->hole
split old frag 0x19000-0x3b000 -->hole
split old frag 0xe000-0x13000 -->hole
split old frag 0x43000-0x5b000 -->hole
split old frag 0x30000-0x3b000 -->hole
split old frag 0x38000-0x3b000 -->hole
split old frag 0x1a000-0x2a000 -->hole
split old frag 0x5d000-0x68000 -->hole
split old frag 0x0000-0x6000 -->hole
split old frag 0x1000-0x14000 -->hole
split old frag 0x4000-0x14000 -->hole
split old frag 0x0000-0x40000 -->hole
split old frag 0x0000-0x32000 -->hole
split old frag 0x0000-0x2c000 -->hole
split old frag 0x0000-0x28000 -->hole
split old frag 0x8000-0x12000 -->hole
split old frag 0x13000-0x28000 -->hole
split old frag 0x39000-0x40000 -->hole
split old frag 0x13000-0x18000 -->hole
split old frag 0x7000-0x1b000 -->hole
split old frag 0x7000-0x10000 -->hole
split old frag 0x1e000-0x26000 -->hole
split old frag 0x3000-0x15000 -->hole
split old frag 0x2f000-0x5e000 -->hole
split old frag 0x34000-0x5e000 -->hole
split old frag 0x34000-0x58000 -->hole
split old frag 0x41000-0x58000 -->hole
split old frag 0x41000-0x56000 -->hole
split old frag 0x5000-0x25000 -->hole
split old frag 0x4d000-0x56000 -->hole
split old frag 0x4d000-0x54000 -->hole
split old frag 0xf000-0x22000 -->hole
split old frag 0x17000-0x22000 -->hole
split old frag 0xf000-0x15000 -->hole
split old frag 0x0000-0x9000 -->hole
split old frag 0x0000-0x1e000 -->hole
split old frag 0x12000-0x1e000 -->hole
split old frag 0x16000-0x1e000 -->hole
split old frag 0x3000-0xf000 -->hole
split old frag 0x20000-0x28000 -->hole
split old frag 0x3000-0x8000 -->hole
split old frag 0x0000-0x22000 -->hole
split old frag 0x33000-0x68000 -->hole
split old frag 0x0000-0x1c000 -->hole
split old frag 0x4b000-0x68000 -->hole
split old frag 0x4d000-0x68000 -->hole
split old frag 0x10000-0x1c000 -->hole
split old frag 0x52000-0x68000 -->hole
split old frag 0x52000-0x64000 -->hole
split old frag 0x0000-0x13000 -->hole
split old frag 0x15000-0x1a000 -->hole
split old frag 0x0000-0x14000 -->hole
split old frag 0xc000-0x14000 -->hole
split old frag 0x0000-0x61000 -->hole
split old frag 0xd1000-0xf7000 -->hole
split old frag 0x69000-0xc7000 -->hole
split old frag 0x39000-0x61000 -->hole
split old frag 0x0000-0x37000 -->hole
split old frag 0x39000-0x5f000 -->hole
split old frag 0xd1000-0xee000 -->hole
split old frag 0x69000-0xa6000 -->hole
split old frag 0x0000-0x2d000 -->hole
split old frag 0x5a000-0x5f000 -->hole
split old frag 0x39000-0x56000 -->hole
split old frag 0x34000-0x37000 -->hole
split old frag 0xa7000-0xc7000 -->hole
split old frag 0x10c000-0x11a000 -->hole
split old frag 0xbe000-0xc7000 -->hole
split old frag 0x6a000-0x9e000 -->hole
split old frag 0xd1000-0xe5000 -->hole
split old frag 0x74000-0x9e000 -->hole
split old frag 0x39000-0x49000 -->hole
split old frag 0x98000-0x9e000 -->hole
split old frag 0x3b000-0x49000 -->hole
split old frag 0x0000-0x1b000 -->hole
split old frag 0x74000-0x92000 -->hole
split old frag 0x0000-0x18000 -->hole
split old frag 0x4b000-0x56000 -->hole
split old frag 0xa1000-0xa6000 -->hole
split old frag 0x3b000-0x3e000 -->hole
split old frag 0x0000-0xe000 -->hole
split old frag 0x1e000-0x2d000 -->hole
split old frag 0x4b000-0x54000 -->hole
split old frag 0x1e000-0x2a000 -->hole
split old frag 0xd5000-0xe0000 -->hole
split old frag 0x0000-0x45000 -->hole
split old frag 0x49000-0xd9000 -->hole
split old frag 0x49000-0xad000 -->hole
split old frag 0xb2000-0xd9000 -->hole
split old frag 0x9000-0x45000 -->hole
split old frag 0x49000-0x9a000 -->hole
split old frag 0x9000-0x25000 -->hole
split old frag 0xa5000-0xad000 -->hole
split old frag 0x26000-0x45000 -->hole
split old frag 0x26000-0x3f000 -->hole
split old frag 0x49000-0x92000 -->hole
split old frag 0x49000-0x75000 -->hole
split old frag 0xdd000-0xe5000 -->hole
split old frag 0xb3000-0xc8000 -->hole
split old frag 0xb3000-0xbc000 -->hole
split old frag 0x2e000-0x3f000 -->hole
split old frag 0x5b000-0x75000 -->hole
split old frag 0xc2000-0xc8000 -->hole
split old frag 0x81000-0x91000 -->hole
split old frag 0xcc000-0xd8000 -->hole
split old frag 0x10000-0x18000 -->hole
split old frag 0x0000-0x33000 -->hole
split old frag 0x0000-0x31000 -->hole
split old frag 0x0000-0x1c000 -->hole
split old frag 0x0000-0xc000 -->hole
split old frag 0x5000-0xc000 -->hole
split old frag 0x0000-0x28000 -->hole
split old frag 0xf000-0x28000 -->hole
split old frag 0x2e000-0x44000 -->hole
split old frag 0x16000-0x28000 -->hole
split old frag 0x0000-0x15000 -->hole
split old frag 0x26000-0x3e000 -->hole
split old frag 0x19000-0x23000 -->hole
split old frag 0xa000-0x15000 -->hole
split old frag 0x19000-0x1e000 -->hole
split old frag 0x0000-0x1a000 -->hole
split old frag 0x9000-0x1a000 -->hole
split old frag 0x0000-0x3000 -->hole
split old frag 0x0000-0x6000 -->hole
split old frag 0x0000-0x21000 -->hole
split old frag 0x9000-0x21000 -->hole
split old frag 0x11000-0x21000 -->hole
split old frag 0x9000-0x10000 -->hole
split old frag 0x3000-0x6000 -->hole
VFS: Mounted root (jffs2 filesystem).
Freeing unused kernel memory: 64k freed
split old frag 0x0000-0x22000 -->hole
split old frag 0x33000-0x68000 -->hole
split old frag 0x0000-0x1c000 -->hole
split old frag 0x4b000-0x68000 -->hole
split old frag 0x4d000-0x68000 -->hole
split old frag 0x10000-0x1c000 -->hole
split old frag 0x52000-0x68000 -->hole
split old frag 0x52000-0x64000 -->hole
split old frag 0x0000-0x34000 -->hole
split old frag 0x2b000-0x34000 -->hole
split old frag 0x14000-0x2a000 -->hole
split old frag 0x35000-0x4b000 -->hole
split old frag 0x43000-0x4b000 -->hole
split old frag 0x24000-0x2a000 -->hole
Algorithmics/MIPS FPU Emulator v1.4
mkdir: Cannot create directory `/etcsplit old frag 0x3000-0x6000 -->hole
/csplit old frag 0x0000-0x21000 -->hole
split old frag 0x9000-0x21000 -->hole
split old frag 0x11000-0x21000 -->hole
split old frag 0x9000-0x10000 -->hole
onfig': Filesplit old frag 0x0000-0x28000 -->hole
split old frag 0xf000-0x28000 -->hole
split old frag 0x2e000-0x44000 -->hole
split old frag 0x16000-0x28000 -->hole
split old frag 0x0000-0xc000 -->hole
split old frag 0x5000-0xc000 -->hole
exisplit old frag 0x0000-0x15000 -->hole
split old frag 0x26000-0x3e000 -->hole
split old frag 0x19000-0x23000 -->hole
split old frag 0xa000-0x15000 -->hole
split old frag 0x19000-0x1e000 -->hole
sts
split old frag 0x0000-0x6000 -->hole
split old frag 0x0000-0x33000 -->hole
split old frag 0x0000-0x31000 -->hole
split old frag 0x0000-0x1c000 -->hole
split old frag 0x10000-0x18000 -->hole
split old frag 0x0000-0x3000 -->hole
split old frag 0x0000-0x1a000 -->hole
split old frag 0x9000-0x1a000 -->hole
insmod: voxgpio.o: no module by that name found
Using /lib/modules/2.4.18/kernel/drivers/net/usb/usb.o
Installing LINUX USB FUSIV DRIVER..........
Using /lib/modules/2.4.18/kernel/drivers/scsi/scsi_mod.o
SCSI subsystem driver Revision: 1.00
Using /lib/modules/2.4.18/kernel/drivers/scsi/sd_mod.o
Using /lib/modules/2.4.18/kernel/drivers/usb/usbcore.o
usb.c: registered new driver hub
Using /lib/modules/2.4.18/kernel/drivers/usb/storage/usb-storaInitializing USB M
ass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
ge.o
Using /lib/modules/2.4.18/kernel/usb.c: registered new driver usblp
printer.c: v0.13: USB Printer Device Class driver
drivers/usb/printer.o
Using /lib/modules/2.4.18/kernel/drivers/usb/host/usb-uhci.o
usb-uhci.c: $Revision: 1.1.1.1 $ time 10:40:21 Feb 25 2006
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0x0, IRQ 4
Detected 2 ports<6>usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.28:UHCI driver, Leo changed for VOX200 board.
init_mac(): 0:d0:d0:b8:5:73
Using /lib/modules/2.4.18/kernel/drivers/char/voice/dspvoice.o
sierra_open is called
EMACMON: add EMAC 1 to monitored list
sierra_open is called
EMACMON: add EMAC 2 to monitored list
config DownloadOpts for 2nd DSP is 4 chan G711
Found the DSP Image[/lib/modules/2.4.18/kernel/drivers/char/voice/dsp218x_2ch_g7
11.img] of 245395 words
No of words read : 245395
Total Number of words : 49079
0 ==== ADSP218x DOWNLOAD BEGINS !!!!
Found the DSP Image[/lib/modules/2.4.18/kernel/drivers/char/voice/dsp218x_4ch_g7
11.img] of 276031 words
No of words read : 276031
Total Number of words : 46006
1 ==== ADSP218x DOWNLOAD BEGINS !!!!
DSP TIME SLOT Assigned:3
DSP CLock Assigned:15
DSP Codec TypeAssigned:1
DSP TIME SLOT Assigned:1360
DSP CLock Assigned:15
DSP Codec TypeAssigned:1
ADSP218x DOWNLOAD DONE !!!!
DSP Ver No:1.1
Initializing SLIC and VOICE Wait Queues
Registering Call Back Handlers
Initializing Voice
Initializing SPI Module
Enable IRQ for DSP
dspInntr DSP1 is Done f0f030f
dspInntr DSP2 is Done f0f0f0f
Gain -3 DB
Gain -3 DB
Gain -3 DB
Gain -3 DB
Gain -3 DB
Gain -3 DB
DSP System Initialized Successfully
Using /lib/modules/2.4.18/kernel/drivers/char/slc/spi_ad6843.o
Using /lib/modules/2.4.18/kernel/drivers/char/slc/usr_line.o
Using /lib/modules/2.4.18/kernel/drivers/char/slc/leg88221.o
Using /lib/modules/2.4.18/kernel/drivers/char/slc/peb2466.o
Using /lib/modules/2.4.18/kernel/drivers/net/wireless/atheros/wlan.o
wlan: 0.8.4.2 (Atheros/multi-bss)
Using /lib/modules/2.4.18/kernel/drivers/net/wireless/atheros/ath_hal.o
ath_hal: 0.9.14.25 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413)
Using /lib/modules/2.4.18/kernel/drivers/net/wirelath_rate_atheros: Version 2.0.
1
Copyright (c) 2001-2004 Atheros Communications, Inc, All Rights Reserved
ess/atheros/ath_rate_atheros.o
Using /lib/modules/2.4.18/kernel/drivers/net/wireless/atheros/wlan_wep.o
Using /lib/modules/2.4.18/kerwlan: mac acl policy registered
nel/drivers/net/wireless/atheros/wlan_acl.o
Using /lib/modules/2.4.18/kernel/drivers/net/wireless/atheros/wlan_ccmp.o
Using /lib/modules/2.4.18/kernel/drivers/net/wireless/atheros/wlan_tkip.o
Using /lib/modules/2.4.18/kernel/drivers/net/wireless/atheros/wlan_xauth.o
call idmaThread() in atmaptmapdriver.c
initADSLInterface():is called!!
initAdslUserCmv():is called!!
call adiAdsl_CreateSwapPages!!
L1 code download SUCCEssed.
**** InitIDMAboot is called !!!****
H100 printd start
<7>split old frag 0x0000-0x6000 -->hole
split old frag 0x0000-0x2a000 -->hole
Process oamd(89) Created!
split old frag 0x0000-0x45000 -->hole
split old frag 0x49000-0xd9000 -->hole
split old frag 0x49000-0xad000 -->hole
split old frag 0xb2000-0xd9000 -->hole
split old frag 0x9000-0x45000 -->hole
split old frag 0x49000-0x9a000 -->hole
split old frag 0x9000-0x25000 -->hole
split old frag 0xa5000-0xad000 -->hole
split old frag 0x26000-0x45000 -->hole
split old frag 0x26000-0x3f000 -->hole
split old frag 0x49000-0x92000 -->hole
split old frag 0x49000-0x75000 -->hole
split old frag 0xdd000-0xe5000 -->hole
split old frag 0xb3000-0xc8000 -->hole
split old frag 0xb3000-0xbc000 -->hole
split old frag 0x2e000-0x3f000 -->hole
split old frag 0x5b000-0x75000 -->hole
split old frag 0xc2000-0xc8000 -->hole
split old frag 0x81000-0x91000 -->hole
split old frag 0xcc000-0xd8000 -->hole
ZXV10-H101 login: Receive split old frag 0x0000-0x13000 -->hole
split old frag 0x19000-0x5b000 -->hole
split old frag 0x19000-0x3b000 -->hole
split old frag 0xe000-0x13000 -->hole
split old frag 0x43000-0x5b000 -->hole
split old frag 0x30000-0x3b000 -->hole
split old frag 0x38000-0x3b000 -->hole
split old frag 0x1a000-0x2a000 -->hole
split old frag 0x5d000-0x68000 -->hole
split old frag 0x0000-0x6000 -->hole
cmdline split old frag 0x7000-0x1b000 -->hole
split old frag 0x7000-0x10000 -->hole
split old frag 0x1e000-0x26000 -->hole
"webd -S"(1split old frag 0x2f000-0x5e000 -->hole
split old frag 0x34000-0x5e000 -->hole
split old frag 0x34000-0x58000 -->hole
split old frag 0x41000-0x58000 -->hole
split old frag 0x41000-0x56000 -->hole
split old frag 0x5000-0x25000 -->hole
split old frag 0x4d000-0x56000 -->hole
split old frag 0x4d000-0x54000 -->hole
split old frag 0xf000-0x22000 -->hole
split old frag 0x17000-0x22000 -->hole
split old frag 0xf000-0x15000 -->hole
003)
Process webd(90) Created!
Receive cmdline "vsftpd"(1003)
Process vsplit old fr
ag 0x0000-0x14000 -->hole
split old frag 0xc000-0x14000 -->hole
sftpd(91) Created!
Receive csplit old frag 0x0000-0x61000 -->hole
split old frag 0xd1000-0xf7000 -->hole
split old frag 0x69000-0xc7000 -->hole
split old frag 0x39000-0x61000 -->hole
split old frag 0x0000-0x37000 -->hole
split old frag 0x39000-0x5f000 -->hole
split old frag 0xd1000-0xee000 -->hole
split old frag 0x69000-0xa6000 -->hole
split old frag 0x0000-0x2d000 -->hole
split old frag 0x5a000-0x5f000 -->hole
split old frag 0x39000-0x56000 -->hole
split old frag 0x34000-0x37000 -->hole
split old frag 0xa7000-0xc7000 -->hole
split old frag 0x10c000-0x11a000 -->hole
split old frag 0xbe000-0xc7000 -->hole
split old frag 0x6a000-0x9e000 -->hole
split old frag 0xd1000-0xe5000 -->hole
split old frag 0x74000-0x9e000 -->hole
split old frag 0x39000-0x49000 -->hole
split old frag 0x98000-0x9e000 -->hole
split old frag 0x3b000-0x49000 -->hole
split old frag 0x0000-0x1b000 -->hole
split old frag 0x74000-0x92000 -->hole
split old frag 0x0000-0x18000 -->hole
split old frag 0x4b000-0x56000 -->hole
split old frag 0xa1000-0xa6000 -->hole
split old frag 0x3b000-0x3e000 -->hole
split old frag 0x0000-0xe000 -->hole
split old frag 0x1e000-0x2d000 -->hole
split old frag 0x4b000-0x54000 -->hole
split old frag 0x1e000-0x2a000 -->hole
split old frag 0xd5000-0xe0000 -->hole
mdline "tr069"(1003)
Process tr069(92) Created!
oamd init_system
Receivsplit old fr
ag 0x0000-0x1e000 -->hole
split old frag 0x12000-0x1e000 -->hole
split old frag 0x16000-0x1e000 -->hole
split old frag 0x3000-0xf000 -->hole
split old frag 0x20000-0x28000 -->hole
split old frag 0x3000-0x8000 -->hole
e cmdline "syslogd"(2001)
Receive cmdlinesplit old frag 0x3000-0x15000 -->hole
"syslogd"(1001)
Process split old frag 0x0000-0x32000 -->hole
split old frag 0x3000-0x32000 -->hole
split old frag 0x16000-0x32000 -->hole
split old frag 0x22000-0x32000 -->hole
split old frag 0x5000-0x15000 -->hole
split old frag 0x5000-0x11000 -->hole
split old frag 0x2a000-0x32000 -->hole
split old frag 0x6000-0xe000 -->hole
split old frag 0x1a000-0x1f000 -->hole
syslogd(96) Created!
initializing vlan ....
new vlan, id: 1, pri: 0
Added VLAN with VID == 1 to IF -:eth0:-
WARNING:VLAN 1 does not work with many
switches,
consider another number if you have problems.
Set egress mapping on devi
ce -:eth0.1:- Should be visible in /proc/net/vlan/eth0.1
Set egress mapping on de
vice -:eth0.1:- Should be visible in /proc/net/vlan/eth0.1
Set egress mapping on
device -:eth0.1:- Should be visible in /proc/net/vlan/eth0.1
Set egress mapping o
n device -:eth0.1:- Should be visible in /proc/net/vlan/eth0.1
Set egress mapping
on device -:eth0.1:- Should be visible in /proc/net/vlan/eth0.1
Set egress mappi
ng on device -:eth0.1:- Should be visible in /proc/net/vlan/eth0.1
Set egress map
ping on device -:eth0.1:- Should be visible in /proc/net/vlan/eth0.1
Set egress m
apping on device -:eth0.1:- Should be visible in /proc/net/vlan/eth0.1
SIOCGIFFLA
GS: No such device
ERROR: trying to remove VLAN -:eth0.2:- error: Invalid argumen
t
SIOCGIFFLAGS: No such device
ERROR: trying to remove VLAN -:eth0.3:- error: Inva
lid argument
SIOCGIFFLAGS: No such device
ERROR: trying to remove VLAN -:eth0.4:-
error: Invalid argument
initializing lan group ....
SIOCGIFFLAGS: No such device
br
idge langroup2 doesn't exist; can't delete it
SIOCGIFFLAGS: No such device
bridge
langroup3 doesn't exist; can't delete it
SIOCGIFFLAGS: No such device
bridge langr
oup4 doesn't exist; can't delete it
SIOCSIFMTU: No such device
SIOCSIFMTU: No such
device
SIOCSIFMTU: No such device
SIOCSIFMTU: No such device
SIOCSIFMTU: No such d
evice
split old frag 0x0000-0x8000 -->hole
bridge langroup2 doesn't exist!
bridge langroup3 doesn't exist!
bridge langroup4 d
oesn't exist!
device usb0 entered promiscuous mode
langroup1: port 1(usb0) entering listening state
langroup1: port 1(usb0) entering learning state
(_llangroup1: port 1(usb0) entering forwarding state
langroup1: topology change detected, propagating
angroup_add_if) ownkey igd.ld1.usb0 add usb0
SIOCSIFADDR: No such device
bridge la
ngroup2 doesn't exist!
bridge langroup3 doesn't exist!
bridge langroup4 doesn't ex
ist!
interface bnep0 does not exist!
(_langroup_adeth0.1: add 01:00:5e:00:00:01 mc
ast address to master interface
d_if) ownkey igd.ld1.bnep0 add bnep0
eth0.1: dev_set_promiscuity(master, 1)
device eth0 entered promiscuous mode
device eth0.1 entered promiscuous mode
langroup1: port 2(eth0.1) entering listening state
langroup1: port 2(eth0.1) entering learning state
langroup1: port 2(eth0.1) entering forwarding state
langroup1: topology change detected, propagating
(_langroup_add_if) ownkey igd.ld1.eth0.1 add eth0.1
SIOCSIFADDR: No such device
de
vice eth0.1 is already a member of a bridge; can't enslave it to bridge langroup
1.
(_langroup_add_if) ownkey igd.ld1.eth0.2 add eth0.2
SIOCSIFADDR: No such device
device eth0.1 is already a member of a bridge; can't enslave it to bridge langro
up1.
(_langroup_add_if) ownkey igd.ld1.eth0.3 add eth0.3
SIOCSIFADDR: No such devi
ce
device eth0.1 is already a member of a bridge; can't enslave it to bridge lang
roup1.
(_langroup_add_if) ownkey igd.ld1.eth0.4 add eth0.4
SIOCSIFADDR: No such de
vice
bridge langroup2 doesn't exist!
bridge langroup3 doesn't exist!
bridge langrou
p4 doesn't exist!
interface nas0 does not exist!
(_langroup_add_if) ownkey igd.ld1
.nas0 add nas0
initializing dns relay......
Receive cmdline "dnsmasq"(2001)
Receive cmdline "dnsmasq -r /etc/config/resolv.co
nf -r /etc/ppp/resolv.conf -r /etc/udhcpc/resolv.conf"(1001)
Process dnsmasq(230)
Created!
Notify, add DSL.CD0
SIOCGIFFLAGS: No such device
Enter b ATM VCC not conf
igured
r2684_cmd_exec br2684ctl -d 0
RFC 1483/2684 bridge:Interface "nas0" done
Exec: br2
684ctl -c 0 -e 0 -q ubr,aal5:max_pcr=3000,pcr=3000,max_cdv=500000,mbs=45 -a 8.81
Enter br2684_cmd_exec br2684ctl -c 0 -e 0 -q ubr,aal5:max_pcr=3000,pcr=3000,max_
cdv=500000,mbs=45 -a 8.81
RFC 1483/2684 bridge:Interface "nas0" created sucessful
ly
RFC 1483/2684 bridge:Communicating over ATM 0.8.81, encapsulation: LLC
RFC 1483
/2684 bridge:Interface configuredRFC 1483/2684 bridge:RFC 1483/2684 bridge start
ed
All of the LANGroups are OK now ** write STR to /etc/snmpd.pid*
Exec: ifconfig
nas0 up
device nas0 entered promiscuous mode
langroup1: port 3(nas0) entering listening state
langroup1: port 3(nas0) entering learning state
langroup1: port 3(nas0) entering forwarding state
langroup1: topology change detected, propagating
initializing route......................
initializing zebra...
initializing rip...
initializing WLAN...
Using /lib/modules/2.4.18/kernel/drivers/net/wireless/athero
s/ath_pci.o
ath_pci: 0.9.4.5 (Atheros/multi-bss)
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36
Mbps 48Mbps 54Mbps
wifi0: mac 7.8 phy 4.5 radio 5.6
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
wifi0: Atheros 5212: mem=0x1a000000, irq=4
Using /lib/modules/2.4.18/kernel/drivers/net/wireless/atheros/wlan_scan_ap.o
wlan
0
split old frag 0x0000-0x3000 -->hole
wlan0 getcountrylist:60
initializing WLAN Paramsplit old frag 0x0000-0xb000
-->hole
split old frag 0x0000-0x4000 -->hole
...
new vlan, id: 1, pri: 0
Added VLAN with VID == 1 to IF -:wlan0:-
WARNING:VLAN 1 does not work with many
switches,
consider another number if you have problems.
process nonify:wlan0__up_
______________wlan0.1
initializing WLAN Security...
wlan0,NONE ffffff80
init_wlan_a
cl.....
wlan0 getacllist:61
First time ,please load saved acl content for wl
an0
register_wlan_rf row=0
This zone's Max txpower is 18 dBm
initializing tc IPQoS
....
get_if_state, return -1
No N/A conn !!!
initializing snooping................
......
Receive split old frag 0x140000-0x255000 -->hole
split old frag 0x140000-0x1b3000 -->hole
cmsplit old frag 0x7000-0xdd000 -->hole
split old frag 0x18000-0xdd000 -->hole
split old frag 0x1d8000-0x255000 -->hole
split old frag 0x46000-0xdd000 -->hole
split old frag 0x18000-0x3d000 -->hole
split old frag 0x46000-0xd4000 -->hole
split old frag 0x1d8000-0x21f000 -->hole
split old frag 0x232000-0x255000 -->hole
split old frag 0x46000-0xd0000 -->hole
split old frag 0x61000-0xd0000 -->hole
split old frag 0x19d000-0x1b3000 -->hole
dsplit old frag 0x232000-0x252000 -->hole
split old frag 0x62000-0xaf000 -->hole
lsplit old frag 0x62000-0x9a000 -->hole
ine "voip sip"(1001)
Process voip(40disable snooping
7) Created!
initializing ddns......................
get_if_state, return -1
Starting System Root Tasktaskinit root task ok
Starting System Exception TaskTimer module Initailized success!
Level Print Initi
alized success!
ScheOne Initialized success!
OSS system Initialized success!
DR_ZTE
open dsp OK
DR_ZTE open voice OK
APP: OnPowerOn
get_if_state, return -1
initializing SNMP...
initializing pt ....
initializing serv
ersplit old frag 0x0000-0x9000 -->hole
..................
initializing IPSec....
apBridgeHook(): port no 3
send
send
send
Using /lib/modules/2.4.18/kernel/net/ipsec/ipsec.o
Running: insmod
ipsec
ret=0
Using /lib/modules/2.4.18/kernel/net/ipsec/alg/ipsec_aes.o
ipsec_aes_i
nit(alg_type=15 alg_id=12 name=aes): ret=0
klips_debug: experimental ipsec_alg_AES_MAC not registered (auth_id=0)
Running: insmod ipsec_aes
ret=0
Running: echo 1 > /proc/sys/net/ipsec/icmp
ret=0
Run
ning: echo 1 > /proc/sys/net/ipsec/inbound_policy_check
ret=0
Running: echo 1 > /p
roc/sys/net/ipsec/tos
ret=0
Running: eroute --clear
ret=0
Running: spi --clear
ret=0
R
eceive cmdlisplit old frag 0x0000-0xc2000 -->hole
split old frag 0x43000-0xc2000 -->hole
split old frag 0x54000-0xc2000 -->hole
split old frag 0x0000-0x41000 -->hole
split old frag 0x4000-0x3f000 -->hole
split old frag 0xa1000-0xc2000 -->hole
split old frag 0xa1000-0xbe000 -->hole
split old frag 0x4000-0x31000 -->hole
split old frag 0x4000-0x1e000 -->hole
split old frag 0x4000-0x12000 -->hole
split old frag 0xb5000-0xbe000 -->hole
split old frag 0x62000-0x7d000 -->hole
ne "pluto --nofork --uniqueids"(1001)
Process pluto(454) Created!
Running: echo ""
> /etc/ipsec.secrets
ret=0
AP2AP enable...
interface bnep0 does not exist!
(langr
oup_del_if) ownkey igd.ld1.bnep0
invoke rf_switch_act
Pluto initialized
SIOCSIFFLA
GS: Network is down
bridge langroup2 doesn't exist!
bridge langroup3 doesn't exist
!
bridge langroup4 doesn't exist!
device wlan0.1 entered promiscuous mode
APP: Data Load Default OK!
int start_init_data(): 6
(_langroup_add_if) ownkey igd.lwlan0.1: dev_set_promiscu
ity(master, 1)
device wlan0 entered promiscuous mode
wlan0.1: add 01:00:5e:00:00:01 mcast address to master interface
langroup1: port 4(wlan0.1) entering listening state
langroup1: port 4(wlan0.1) entering learning state
d1.wlalangroup1: port 4(wlan0.1) entering forwarding state
langroup1: topology change detected, propagating
n0.1 add wlan0.1
invoke rf_switch_act
OAM data ok
APP: OnSyncDataOK
APP: RTP Init OK!
CTP_AGENT: init...
SIP Enter SIP_ST_INIT For Server Host Or Local Host UnConfiged
RCA PowerOn!
SLC Control PowerOn!
SLC Report PowerOn!
No route to host
Connect try 1 times
get_http_sockfd fail!
Destroying request!
Closi
ng connection! 问题解决了 路由用http是登陆不了的要用https 而且要在ie选项里把ssl2.0 ssl3.0 tls 1.0 三项勾上才可以 不然用https也登陆不了 谁有使用说明上传一份 谁有说明书啊上传一份上来 网上找不到
页:
[1]