用D828数据线改的TTL线进不了CFE模式
是PL2302的芯片， 就3根线。 插上后能显示CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: 二1月 29 07:41:15 CST 2008 (root@ZTJ)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot Kern
AuxFS Misc PSI
Flash RootFS Partition Length: 12320768
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x805285A0 (1209760)
Initialized Data: 0x8041DD30 - 0x8041FDC0 (8336)
BSS Area: 0x8041FDC0 - 0x804265A0 (26592)
Local Heap: 0x804265A0 - 0x805265A0 (1048576)
Stack Area: 0x805265A0 - 0x805285A0 (8192)
Text (code) segment: 0x80401000 - 0x8041DD30 (118064)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.159
Gateway IP address :
Run from flash/host (f/h) : h
Default host run file name : 308nfs6358
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-9) : 96358VW2
Number of MAC Addresses (1-32) : 24
Base MAC Address : 00:1e:40:47:13:da
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from latest image (0xbe600000) ...
Code Address: 0x80010000, Entry Address: 0x80263018
Decompression OK!
显示Press any key to stop auto run的时候我按了键盘，但是没反应。 然后就全部自动下去了， 键盘一直没有响应。 是不是输出线没信号？？但是我打环路后测，能收到自己发的数据的呀。 ipt_hashlimit: Unknown symbol ipt_unregister_match
insmod: cannot insert `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ipt_hashlimit.ko': Success (2): Success
iptables v1.2.11: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
br0: port 2(eth0) entering disabled state
br0: port 4(eth1.2) entering disabled state
br0: port 5(eth1.3) entering disabled state
br0: port 6(eth1.4) entering disabled state
br0: port 1(usb0) entering disabled state
这是最后几行，然后就没反应了， 按键盘没反应 按键没有反应,要么是数据线接得不好,要么就是接反了.仔细检查一下喔 qqqqqqqqqqqqqqqqqqqq 按键没有反应,要么是数据线接得不好,要么就是接反了.仔细检查一下喔
天涯 发表于 2009-5-22 20:17 https://www.chinadsl.net/images/common/back.gif
接反了应该收不到数据的啊， 但是我收的到。 接地也肯定对的，上面标着的。。。 查数据线所使用的IC,对照IC的DATASHEET,用表把正确的线找出来,仔细查找和核对,应该能搞定.这些只能靠自己了,别人帮不上忙的.实在不想折腾就直接花银子买根线算了.反正线也不贵应该在20-30左右.
我的数据线是当年的NOKIA 6100配的.手机被盗,把线改了.当年买手机的时候那线是花了110元的,(NOKIA)真TNND的黑,我KAO.后来才知道,其实买兼容的数据线搞NOKIA 6100也是一样用的.呜~~~~~~~~
页:
[1]