RG100A 刷2740问题！！！
由于刷固件失败，jtag恢复了2.61的cfe。后刷了2次2.61带cfe的fw，再刷2次2.89，在cfe中改好Board了，还是启动不了，进入系统，到底是怎么回事？启动信息：
Use default boot line parameters: e=192.168.1.1:ffffff00 h=192.168.1.100 g= r=f f=vmlinux i=bcm963xx_fs_kernel d=1 p=0
*** Restore to Factory Default Setting ***
*** Break into CFE console ***
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-15) : 96358VW2
Number of MAC Addresses (1-32) : 12
Base MAC Address : 00:1f:a3:b4:ea:89
PSI Size (1-64) KBytes : 24
Main Thread Number : 0
web info: Waiting for connection on socket 0.
CFE> i
Erase persisten storage data? (y/n):y
*** command status = 0
CFE> r
Booting from latest image (0xbe800000) ...
Code Address: 0x80010000, Entry Address: 0x801ac018
Decompression OK!
Entry at 0x801ac018
Closing network.
Starting program at 0x801ac018
Linux version 2.6.8.1 (root@fc6.ayecom.com) (gcc version 3.4.2) #1 Wed Jan 21 23:56:28 CLST 2009
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 4000 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 30160k/32384k available (1429k kernel code, 2180k reserved, 215k data, 72k init, 0k highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80e00000 ... 0x80f00000>
Calibrating delay loop... 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...unavailable.
NET: Registered protocol family 16
Total Flash size: 16384K with 128 sectors
File system address: 0xbe800100
Can't analyze prologue code at 80173cc4
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v1.0
brcmboard: brcm_board_init entry
Invalid External Interrupt definition
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
u32 classifier
OLD policer on
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET: Registered protocol family 1
NET: Registered protocol family 17
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 72k freed
init started:BusyBox v1.00 (2009.01.22-02:59+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
BusyBox v1.00 (2009.01.22-02:59+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Jan 21 2009 23:55:01
Config Ethernet Switch Through MDIO Pseudo PHY Interface
dgasp: kerSysRegisterDyingGaspHandler: eth0 registered
eth0: MAC Address: 00:1F:A3:B4:EA:89
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 00:1F:A3:B4:EA:8A
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.174.64.12.cpe1.1
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
eth0 Link UP.
app: wlctl country list a > /var/wlclist
app: wlctl country list b > /var/wlclist
BcmAdsl_Initialize=0xC005D3C8, g_pFnNotifyCallback=0xC0076294
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
pSdramPHY=0xA1FFFFF8, 0x11F17 0xDEADBEEF
AdslCoreHwReset: AdslOemDataAddr = 0xA1FFD3D4
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
app: atmctl start --pqs 125
ATM proc init !!!
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (253 buckets, 0 max) - 384 bytes per conntrack
ip_conntrack_pptp version 2.1 loaded
ip_nat_pptp version 2.0 loaded
ip_ct_h323: init success
ip_nat_h323: init success
ip_conntrack_rtsp v0.01 loading
ip_nat_rtsp v0.01 loading
ipt_time loading
app: insmod /lib/modules/2.6.8.1/kernel/net/bridge/netfilter/ebt_iprange.ko
==> Bcm963xx Software Version: EU_2.89 <==
app: echo "3" > /proc/sys/net/ipv4/conf/all/force_igmp_version
app: echo "1" > /proc/sys/net/ipv4/ip_forward
app: echo "1" > /proc/sys/net/ipv4/ip_dynaddr
app: echo "1" > /proc/sys/net/ipv4/icmp_echo_ignore_broadcasts
app: pvc2684d &
app: echo > /etc/pppmsg
app: brctl addbr br0
app: brctl stp br0 off
app: brctl setfd br0 0
app: ifconfig eth0 up
app: ifconfig br0 192.168.1.1 netmask 255.255.255.0 broadcast 192.168.1.255 up
app: ifconfig eth0 up 2>/dev/null
app: brctl addif br0 eth0 2>/dev/null
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
app: sendarp -s br0 -d br0
app: sendarp -s br0 -d br0
app: sendarp -s br0 -d eth0
restrieve 1 ok !
restrieve 2 ok !, num = 4
num<WL_NUM_SSID ok !
restrieve 3 ok !
app: wlctl wds none
app: wlctl down
app: wlctl mbss 1
app: wlctl bss -C 0 down
app: wlctl bss -C 1 down
app: wlctl bss -C 2 down
app: wlctl bss -C 3 down
app: wlctl ssid -C 0 'D''L''i''n''k'
Setting SSID "DLink"
app: ifconfig wl0 down 2>/dev/null
app: ifconfig wl0.1 down 2>/dev/null
app: ifconfig wl0.2 down 2>/dev/null
app: ifconfig wl0.3 down 2>/dev/null
app: ifconfig wl0 hw ether 00:1F:A3:B4:EA:8A 2>/dev/null
app: wlctl -i wl0 cur_etheraddr 00:1F:A3:B4:EA:8A2>/dev/null
app: ifconfig wl0.1 hw ether 5a:1f:a3:b4:ea:8b 2>/dev/null
app: wlctl -i wl0.1 cur_etheraddr 5a:1f:a3:b4:ea:8b2>/dev/null
app: ifconfig wl0.2 hw ether 5a:1f:a3:b4:ea:88 2>/dev/null
app: wlctl -i wl0.2 cur_etheraddr 5a:1f:a3:b4:ea:882>/dev/null
app: ifconfig wl0.3 hw ether 5a:1f:a3:b4:ea:89 2>/dev/null
app: wlctl -i wl0.3 cur_etheraddr 5a:1f:a3:b4:ea:892>/dev/null
app: wlctl ap 1
app: wlctl -i wl0 closed 0
app: wlctl country GB
Setting country code using abbreviation: "GB"
app: wlctl band b
app: wlctl regulatory 0
app: wlctl radar 0
wlctl: Unsupported
app: wlctl spect 0
app: wlctl channel 1
app: wlctl wpa_cap -C 0 12 2>/dev/null
wlctl: Not Found
app: wlctl wpa_cap -C 1 0 2>/dev/null
wlctl: Not Found
app: wlctl wpa_cap -C 2 0 2>/dev/null
wlctl: Not Found
app: wlctl wpa_cap -C 3 0 2>/dev/null
app: wlctl -i wl0 maxassoc 128
app: wlctl gmode Auto
app: wlctl gmode_protection_override -1
app: wlctl gmode_protection_control 2
app: wlctl nmode 0; wlctl gmode 1; wlctl nmode 1
wlctl: Bad Band
app: wlctl rate 0 ;wlctl bg_rate 0 ;
app: wlctl mrate -1 ;wlctl bg_mrate -1 ;
app: wlctl rateset default
app: wlctl rtsthresh 2347
app: wlctl fragthresh 2346
app: wlctl dtim 1
app: wlctl bi 100
app: wlctl afterburner_override 0
app: wlctl wme 1
app: wlctl wme_noack 0
app: wlctl wme_apsd 1
app: wlctl -i wl0 wme_bss_disable 0
app: wlctl afterburner_override 0
app: wlctl frameburst 0
app: wlctl -i wl0 ap_isolate 0
app: wlctl -i wl0 wme_bss_disable 0
app: wlctl wds none
app: wlctl pwr_percent 100
app: wlctl -i wl0 mac none
app: wlctl -i wl0 macmode 0
app: wlctl lazywds 0
app: wlctl wds
app: ebtables -t nat -A POSTROUTING --out-if wl0 -p IPV4 -j wmm-mark> /dev/null 2>&1
app: ebtables -t nat -A POSTROUTING --out-if wl0 -p 802_1Q -j wmm-mark --wmm-marktag vlan> /dev/null 2>&1
app: wlctl up
app: wlctl antdiv 0
KLOB extended to 2 pools
app: wlctl txant 0
app: wlctl csscantimer 0
app: wlctl rmwep -C 0 0
app: wlctl rmwep -C 0 1
app: wlctl rmwep -C 0 2
app: wlctl rmwep -C 0 3
app: wlctl rmwep -C 1 0
app: wlctl rmwep -C 1 1
app: wlctl rmwep -C 1 2
app: wlctl rmwep -C 1 3
app: wlctl rmwep -C 2 0
app: wlctl rmwep -C 2 1
app: wlctl rmwep -C 2 2
app: wlctl rmwep -C 2 3
app: wlctl rmwep -C 3 0
app: wlctl rmwep -C 3 1
app: wlctl rmwep -C 3 2
app: wlctl rmwep -C 3 3
app: wlctl wsec -C 0 0
app: wlctl wsec_restrict -C 0 0
app: wlctl wpa_auth -C 0 0
app: wlctl eap 0
app: wlctl auth -C 0 0
app: wlctl bss -C 0 up
app: wlctl bss -C 1 down
app: wlctl bss -C 2 down
app: wlctl bss -C 3 down
app: ifconfig wl0 up
app: ifconfig wl0 up 2>/dev/null
app: brctl addif br0 wl0 2>/dev/null
device wl0 entered promiscuous mode
br0: port 2(wl0) entering learning state
br0: topology change detected, propagating
br0: port 2(wl0) entering forwarding state
app: sendarp -s br0 -d br0
startServices@4674 m_wlVar.wlEnbl= wlInitDone=
app: sendarp -s br0 -d br0
app: dhcpd &> /dev/null &
app: brctl delif br0 eth0 2>/dev/null
device eth0 left promiscuous mode
br0: port 1(eth0) entering disabled state
app: sendarp -s br0 -d br0
app: ifconfig eth0 up 2>/dev/null
app: ethctl eth0 vport query 2>/var/vcfgerr
app: rm /var/vcfgerr
app: insmod /lib/modules/2.6.8.1/extra/vnet.ko
eth0.2: MAC Address: 00:1F:A3:B4:EA:89
eth0.3: MAC Address: 00:1F:A3:B4:EA:89
eth0.4: MAC Address: 00:1F:A3:B4:EA:89
eth0.5: MAC Address: 00:1F:A3:B4:EA:89
app: ifconfig eth0.2 up
app: ifconfig eth0.3 up
app: ifconfig eth0.4 up
app: ifconfig eth0.5 up
app: ifconfig eth0 up 2>/dev/null
app: brctl delif br0 wl0 2>/dev/null
device wl0 left promiscuous mode
br0: port 2(wl0) entering disabled state
app: sendarp -s br0 -d br0
app: ifconfig wl0 up 2>/dev/null
app: ifconfig eth0 up 2>/dev/null
app: ifconfig wl0 up 2>/dev/null
app: brctl addif br0 wl0 2>/dev/null
device wl0 entered promiscuous mode
br0: port 1(wl0) entering learning state
br0: topology change detected, propagating
br0: port 1(wl0) entering forwarding state
app: sendarp -s br0 -d br0
app: ifconfig eth0.2 up 2>/dev/null
app: brctl addif br0 eth0.2 2>/dev/null
device eth0.2 entered promiscuous mode
br0: port 2(eth0.2) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0.2) entering forwarding state
app: sendarp -s br0 -d br0
app: ifconfig eth0.3 up 2>/dev/null
app: brctl addif br0 eth0.3 2>/dev/null
device eth0.3 entered promiscuous mode
br0: port 3(eth0.3) entering learning state
br0: topology change detected, propagating
br0: port 3(eth0.3) entering forwarding state
app: sendarp -s br0 -d br0
app: ifconfig eth0.4 up 2>/dev/null
app: brctl addif br0 eth0.4 2>/dev/null
device eth0.4 entered promiscuous mode
br0: port 4(eth0.4) entering learning state
br0: topology change detected, propagating
br0: port 4(eth0.4) entering forwarding state
app: sendarp -s br0 -d br0
app: ifconfig eth0.5 up 2>/dev/null
app: brctl addif br0 eth0.5 2>/dev/null
device eth0.5 entered promiscuous mode
br0: port 5(eth0.5) entering learning state
br0: topology change detected, propagating
br0: port 5(eth0.5) entering forwarding state
app: sendarp -s br0 -d br0
startServices@4674 m_wlVar.wlEnbl= wlInitDone=
app: rtpd
Scratch pad is not initialized.
Scratch pad is not initialized.
No scratch pad found.Initialize scratch pad...
br0: port 2(eth0.2) entering disabled state
br0: port 3(eth0.3) entering disabled state
br0: port 4(eth0.4) entering disabled state
Restore default configuration and Reset the system!!!
device eth0.2 left promiscuous mode
br0: port 2(eth0.2) entering disabled state
device eth0.3 left promiscuous mode
br0: port 3(eth0.3) entering disabled state
device eth0.4 left promiscuous mode
br0: port 4(eth0.4) entering disabled state
br0: port 5(eth0.5) entering disabled state
device eth0.5 left promiscuous mode
br0: port 5(eth0.5) entering disabled state
CFE version 1.0.37-11.3 for BCM96358 (32bit,SP,BE)
Build Date: 涓? 5鏈?28 22:37:40 CST 2008 (root@fc6.ayecom.com)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x805284A0 (1209504)
Initialized Data: 0x8041D840 - 0x8041FCC0 (9344)
BSS Area: 0x8041FCC0 - 0x804264A0 (26592)
Local Heap: 0x804264A0 - 0x805264A0 (1048576)
Stack Area: 0x805264A0 - 0x805284A0 (8192)
Text (code) segment: 0x80401000 - 0x8041D83C (116796)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
*** Restore to Factory Default Setting ***
*** Break into CFE console ***
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-15) : 96358VW2
Number of MAC Addresses (1-32) : 12
Base MAC Address : 00:1f:a3:b4:ea:89
PSI Size (1-64) KBytes : 24
Main Thread Number : 0
web info: Waiting for connection on socket 0.
CFE> 问题已找到，把Board Id (0-15): 96358VW2 改为2740b的96358GW,就得了。
把论坛的帖子翻了遍。。。。。。。。 good!!!!!!!!!! Board Id (0-15) : 96358VW2
要改成96358GW 楼上的，已经解决的老帖子你也来翻，真的pf你了，我无语了。。。。 2# haxc
太好了真的是这样了 我也是翻边了论坛才找到你这个太感谢了 不错。。。。
页:
[1]