中兴531B配置文件上看已经开启了telnet可是登陆居然不行,附上配置文件和图大家研究下
本帖最后由 hanmin 于 2009-1-22 19:16 编辑中兴531B配置文件上看已经开启了telnet可是登陆居然不行,附上配置文件和图大家研究下
2个中兴531B为什么一个用telnet登陆不了复位也不行,可是另外一个又没问题.(有图)
求解决办法,我想刷成Dynalink RTA1025W
https://www.chinadsl.net/attachments/ext_jpg/0901211323d71b6cf92c3f3691.jpg.thumb.jpg
以下到尾巴是配置文件,附件里也有下载.
- <psitree>
- <WirelessCfg>
<wlMacFilter tableSize="0" />
<wdsFilter tableSize="0" />
<scanWdsFilter tableSize="0" />
<vars state="disabled" hide="0" ssId="ZXDSL531BII-7093CF" country="AU" Apname="ConnectionPoint" authMode="open" radiusServerIP="0.0.0.0" radiusServerPort="1812" radiusServerKey="" wep="disabled" auth="0" keyBit="128-bit" keyType="ASCII" key64_1="" key64_2="" key64_3="" key64_4="" key64_a_1="" key64_a_2="" key64_a_3="" key64_a_4="" key64Index="0" key128_1="" key128_2="" key128_3="" key128_4="" key128_a_1="" key128_a_2="" key128_a_3="" key128_a_4="" key128Index="0" wpaRekey="0" wpakey="" wpa="tkip" fltMacMode="disabled" apMode="ap" bridgeRestrict="enabled_scan" wdsMAC_0="" wdsMAC_1="" wdsMAC_2="" wdsMAC_3="" apIsolation="off" band="b" channel="11" rate="auto" multicastRate="auto" basicRate="default" fragThreshold="2346" RTSThreshold="2347" DTIM="1" beacon="100" XPress="off" gMode="auto" gProtection="auto" preamble="long" AfterBurner="off" WME="off" WMENoAck="off" Preauthentication="off" ReauthTimeout="36000" />
</WirelessCfg>
- <ADSL>
<settings G.Dmt="enable" G.lite="enable" T1.413="disable" ADSL2="enable" AnnexL="enable" ADSL2plus="enable" AnnexM="disable" pair="inner" bitswap="disable" SRA="disable" ADSLenable="enable" />
</ADSL>
+ <AtmCfgTd>
<td1 cat="UBR" PCR="0" SCR="0" MBS="0" />
</AtmCfgTd>
- <AtmCfgVcc>
<vccId1 vpi="0" vci="35" tdId="1" aalType="AAL5" adminStatus="up" encap="llc" qos="disable" vccPrio="1" />
</AtmCfgVcc>
- <PPCfg>
<groupId0 groupname="Default" ifname="br0" groupedinf="eth0.2|eth0.3|eth0.4|eth0.5|wl0|usb0|nas_0_35|" prio="1" multicast="1" management="1" useflag="1" />
</PPCfg>
- <Lan>
<entry1 address="192.168.1.1" startAddr="192.168.1.3" endAddr="192.168.1.254" mtu="1500" mask="255.255.255.0" dhcpServer="enable" leasedTime="86400" dhcpForever="disable" />
</Lan>
- <SystemInfo>
<sysLog state="disable" displayLevel="ERR" logLevel="DEBUG" option="local" serverIP="0.0.0.0" serverPort="514" />
<snmp state="disable" readCommunity="public" writeCommunity="private" sysName="ZXDSL531BII" sysLocation="ShangHai,CHINA" sysContact="www.zte.com.cn" trapIP="0.0.0.0" trapStatus="disable" />
<sysPassword value="9E9B929691" />
<usrUserName value="8A8C9A8D" />
<usrPassword value="8A8C9A8D" />
<defaultGateway enblGwAutoAssign="enable" ifName="" ipAddr="0.0.0.0" />
<dns dynamic="enable" primary="0.0.0.0" secondary="0.0.0.0" />
<remoteservice value="" />
<authservice value="" />
<protocol autoScan="disable" upnp="enable" igmpSnp="disable" macFilterPolicy="forward" />
<actpppconn value="" />
<domainname value="home" />
<hostname value="ZXDSL531BII" />
<sysFirewall state="enable" />
<sysUserName value="9E9B929691" />
</SystemInfo>
+ <RouteCfg>
<ripGlobal state="disable" ripIfcTableSize="1" />
- <ripIfc tableSize="1">
<ripIfcEntry id="1" name="br0" state="disable" version="2" operation="active" />
</ripIfc>
<route tableSize="0" />
</RouteCfg>
- <SNTPCfg>
<cfg state="disable" server1="time.windows.com" server2="time.nist.gov" timezone="Beijing, Chongquing, Hong Kong, Urumqi" enblLightSaving="1" />
</SNTPCfg>
- <SecCfg>
<vrtSrv tableSize="0" />
<prtTrigger tableSize="0" />
<outFilter tableSize="0" />
<inFilter tableSize="0" />
<qosCls tableSize="0" />
<dmzHost ipAddr="0.0.0.0" wanif="" />
<srvCtrlList ftp="lan" http="lan" icmp="enable" snmp="lan" ssh="lan" telnet="lan" tftp="lan" />
</SecCfg>
- <wan_0_35>
<entry1 vccId="1" conId="1" name="br_0_35" protocol="BRIDGE" encap="LLC" firewall="disable" nat="disable" igmp="disable" vlanId="0" service="enable" remoteWeb="0" remoteTelnet="0" remoteSnmp="0" remotePing="0" remoteFtp="0" remoteTftp="0" remoteSsh="0" remoteipauth="0" remoteWebPort="8080" />
</wan_0_35>
</psitree> 没人理我... 你现在的固件版本是多少
页:
[1]