大亚DB120 WG启动信息!
CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)Build Date: 二1月 29 07:41:15 CST 2008 (root@ZTJ)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot Kern
AuxFS Misc PSI
Flash RootFS Partition Length: 12320768
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x805285A0 (1209760)
Initialized Data: 0x8041DD30 - 0x8041FDC0 (8336)
BSS Area: 0x8041FDC0 - 0x804265A0 (26592)
Local Heap: 0x804265A0 - 0x805265A0 (1048576)
Stack Area: 0x805265A0 - 0x805285A0 (8192)
Text (code) segment: 0x80401000 - 0x8041DD30 (118064)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.159
Gateway IP address :
Run from flash/host (f/h) : h
Default host run file name : 308nfs6358
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-9) : 96358VW2
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:1e:40:30:c8:3d
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xbe020000) ...
Code Address: 0x80010000, Entry Address: 0x80257018
Decompression OK!
Entry at 0x80257018
Closing network.
Starting program at 0x80257018
Linux version 2.6.8.1 (root@qinjian) (gcc version 3.4.2) #1 Thu Feb 21 21:29:49 EST 2008
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Not find second flash
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 4000 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 29428k/32384k available (1908k kernel code, 2912k reserved, 419k data, 76k init, 0k highmem)
Calibrating delay loop... 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...unavailable.
NET: Registered protocol family 16
Computing partition layout for flash of size sectors
Flash split 25% into RootFS+Kernel : AuxFS
Partition ROOTFS_KRN Blks[ 94: 1 ..94]
SubPartition Image 1 Blks[ 47: 1 ..47]
SubPartition Image 2 Blks[ 47:48 ..94]
Blk# BlkOff Blks BlkSize AvailSize MemStart MemLen Partition Name
0 1408 1131072 131072 0xbe000580 1024 BOOTLOADER
1 0 9413107212320768 0xbe020000 12320768 ROOTFS_KRN
95 0 31131072 4063232 0xbebe0000 4063232 JFFS_AUXFS
126 0 1131072 131072 0xbefc0000 131072 LOG_SCRPAD
127 106496 1131072 131072 0xbeffa000 24576 PERSISTMEM
Can't analyze prologue code at 801eba14
SCSI subsystem initialized
usbcore: registered new driver hub
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v2.0
File system address: 0xbe020100
Registered device mtd dev Flash
Registered device mtd dev Flash
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0050300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0052400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x3 is enabled
SES: LED GPIO 0x801b is enabled
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
u32 classifier
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 76k freed
init started:BusyBox v1.00 (2008.02.22-02:35+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
BusyBox v1.00 (2008.02.22-02:35+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Feb 21 2008 21:27:58
Config Internal PHY Through MDIO
BCM63xx_ENET: Auto-negotiation timed-out
BCM63xx_ENET: 10 MB Half-Duplex (assumed)
eth0: MAC Address: 00:1E:40:30:C8:3D
Broadcom BCM6358A1 Ethernet Network Device v0.3 Feb 21 2008 21:27:58
Config Ethernet Switch Through MDIO Pseudo PHY Interface
dgasp: kerSysRegisterDyingGaspHandler: eth1 registered
eth1: MAC Address: 00:1E:40:30:C8:3E
Broadcom BCM6358A1 USB Network Device v0.4 Feb 21 2008 21:28:00
usb0: MAC Address: 00 1E 40 30 C8 3F
usb0: Host MAC Address: 00 1E 40 30 C8 40
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 00:1E:40:30:C8:41
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.120.25.0.cpe1.3
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
BcmAdsl_Initialize=0xC00BA3F8, g_pFnNotifyCallback=0xC00D33C4
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
pSdramPHY=0xA1FFFFF8, 0xDFFFFDFF 0xFFFFFBFD
AdslCoreHwReset: AdslOemDataAddr = 0xA1FFD3D4
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
ATM proc init !!!
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (253 buckets, 0 max) - 376 bytes per conntrack
ip_conntrack_pptp version 2.1 loaded
ip_nat_pptp version 2.0 loaded
ip_ct_h323: init success
ip_nat_h323: init success
ip_conntrack_rtsp v0.01 loading
ip_nat_rtsp v0.01 loading
==> Bcm963xx Software Version: 3.10L.CT_06V.A2pB022g.d20e <==
device usb0 entered promiscuous mode
br0: port 1(usb0) entering learning state
br0: topology change detected, propagating
br0: port 1(usb0) entering forwarding state
device eth0 entered promiscuous mode
br0: port 2(eth0) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0) entering forwarding state
killall: lld2d: no process killed
killall: wsccmd: no process killed
killall: wps_btn: no process killed
Setting SSID "Ren.Yong"
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCSIFHWADDR: No such device
wlctl: wl driver adapter not found
SIOCSIFHWADDR: No such device
wlctl: wl driver adapter not found
SIOCSIFHWADDR: No such device
wlctl: wl driver adapter not found
Setting country code using abbreviation: "CN"
wlctl: Not Found
wlctl: Not Found
wlctl: Not Found
channel 1 selected
wl0: current channel 1
device wl0 entered promiscuous mode
br0: port 3(wl0) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0) entering forwarding state
BcmRfc2684_init interface is not up nas_0_8_35!
pvc2684ctl -a -v 0.8.35 -f &
mac=00:1e:40:30:c8:3d
pvc2684d: Interface "nas_0_8_35" created sucessfully
pvc2684d: Communicating over ATM 0.8.35, encapsulation: LLC
HTB init, kernel part version 3.17
BcmRfc2684_init interface is not up nas_0_0_35!
pvc2684ctl -a -v 0.0.35 &
mac=00:1e:40:30:c8:3d
pvc2684d: Interface "nas_0_0_35" created sucessfully
pvc2684d: Communicating over ATM 0.0.35, encapsulation: LLC
HTB init, kernel part version 3.17
device nas_0_0_35 entered promiscuous mode
br0: port 4(nas_0_0_35) entering learning state
br0: topology change detected, propagating
br0: port 4(nas_0_0_35) entering forwarding state
BcmRfc2684_init interface is not up nas_0_0_127!
pvc2684ctl -a -v 0.0.127 &
mac=00:1e:40:30:c8:3d
pvc2684d: Interface "nas_0_0_127" created sucessfully
pvc2684d: Communicating over ATM 0.0.127, encapsulation: LLC
HTB init, kernel part version 3.17
device nas_0_0_127 entered promiscuous mode
br0: port 5(nas_0_0_127) entering learning state
br0: topology change detected, propagating
br0: port 5(nas_0_0_127) entering forwarding state
eth1.2: MAC Address: 00:1E:40:30:C8:3E
eth1.3: MAC Address: 00:1E:40:30:C8:3E
eth1.4: MAC Address: 00:1E:40:30:C8:3E
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
device usb0 left promiscuous mode
br0: port 1(usb0) entering disabled state
device eth0 left promiscuous mode
br0: port 2(eth0) entering disabled state
device wl0 left promiscuous mode
br0: port 3(wl0) entering disabled state
device nas_0_0_35 left promiscuous mode
br0: port 4(nas_0_0_35) entering disabled state
device nas_0_0_127 left promiscuous mode
br0: port 5(nas_0_0_127) entering disabled state
device usb0 entered promiscuous mode
br0: port 1(usb0) entering learning state
br0: topology change detected, propagating
br0: port 1(usb0) entering forwarding state
device eth0 entered promiscuous mode
br0: port 2(eth0) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0) entering forwarding state
device eth1.2 entered promiscuous mode
br0: port 3(eth1.2) entering learning state
br0: topology change detected, propagating
br0: port 3(eth1.2) entering forwarding state
device eth1.3 entered promiscuous mode
br0: port 4(eth1.3) entering learning state
br0: topology change detected, propagating
br0: port 4(eth1.3) entering forwarding state
device eth1.4 entered promiscuous mode
br0: port 5(eth1.4) entering learning state
br0: topology change detected, propagating
br0: port 5(eth1.4) entering forwarding state
device nas_0_0_35 entered promiscuous mode
br0: port 6(nas_0_0_35) entering learning state
br0: topology change detected, propagating
br0: port 6(nas_0_0_35) entering forwarding state
device nas_0_0_127 entered promiscuous mode
br0: port 7(nas_0_0_127) entering learning state
br0: topology change detected, propagating
br0: port 7(nas_0_0_127) entering forwarding state
device wl0 entered promiscuous mode
br0: port 8(wl0) entering learning state
br0: topology change detected, propagating
br0: port 8(wl0) entering forwarding state
CT SystemLog Init Read From Flash string lenth =12296
CT SystemLog Init Read From Flash string acsloglenth =2881 secloglenth=151
sntp: host not found
DareNtwk_blockmacinit running!!!!!!
br0: port 2(eth0) entering disabled state
br0: port 3(eth1.2) entering disabled state
br0: port 4(eth1.3) entering disabled state
br0: port 5(eth1.4) entering disabled state
br0: port 1(usb0) entering disabled state
CONSOLED launched
Login: admin
Password:
>
这个是调试模式可以使用的命令
CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)Build Date: 二1月 29 07:41:15 CST 2008 (root@ZTJ)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot Kern
AuxFS Misc PSI
Flash RootFS Partition Length: 12320768
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x805285A0 (1209760)
Initialized Data: 0x8041DD30 - 0x8041FDC0 (8336)
BSS Area: 0x8041FDC0 - 0x804265A0 (26592)
Local Heap: 0x804265A0 - 0x805265A0 (1048576)
Stack Area: 0x805265A0 - 0x805285A0 (8192)
Text (code) segment: 0x80401000 - 0x8041DD30 (118064)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.159
Gateway IP address :
Run from flash/host (f/h) : h
Default host run file name : 308nfs6358
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-9) : 96358VW2
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:1e:40:30:c8:3d
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1
web info: Waiting for connection on socket 0.
CFE> help
Available commands:
w Write the whole image start from beginning of the flash
e Erase vram or ll flash except bootrom
r Run program from flash image or from host depend on flag
p Print boot line and board parameter info
c Change booline parameters
f Write image to the flash
i Erase persistent storage data
b Change board parameters
reset Reset the board
flashimage Flashes a compressed image after the bootloader.
help Obtain help for CFE commands
For more information about a command, enter 'help command-name'
*** command status = 0
CFE> 32m内存,秒杀一切无线路由器,就等dd-wrt了 呵呵，还不至于秒杀一切无线路由。
思科WRT54GS V1-V3版本就是32M内存。
贝尔金7231-4P加强版是64M内存。
大家都是Linux内核，不至于大亚的就能强到秒杀的地步。
只能说大亚这个配置可以秒杀国产的无线路由器了。
虽然说主频很重要，BCM6358是300M的主频，是算目前最强的芯片了，但是真正在做应用的时候，大内存的优势更明显。
就像只要完成打字的工作，P4并不比P3优秀多少。更多的在于更大内存的电脑，运行更流畅一点，会更快一些。
[ 本帖最后由 yiping 于 2008-4-12 14:42 编辑 ] 等DD中,,,,,, 我tftp文件上去总是失败，你成功没？ 好奇120主板上哪个孔是 串口 or jtag 接头啊? 发现有5个孔 还有4根针，咋个接法，有没有方法不用修改kernel,先把应用层mount到usb SD卡上来
[ 本帖最后由 virus101 于 2008-4-13 00:13 编辑 ] 高手看看这里，为db120-wg 编译个 应用层程序 应该不成问题吧？ctorrent之类 现在就可实现？
http://www.efixo.com/neufbox4/freesoftware/ 原帖由 virus101 于 2008-4-13 00:24 发表 https://www.chinadsl.net/images/common/back.gif
高手看看这里，为db120-wg 编译个 应用层程序 应该不成问题吧？ctorrent之类 现在就可实现？
http://www.efixo.com/neufbox4/freesoftware/
关键是谁去编呢？ 我是编不来了,
期待高人出现
页:
[1]
2