HG6143F启动信息
HG6143F启动信息：
EN7523DRAMC V0.2
dram_type = 5, speed = 1866
Final Impdance Cal Result: OCDP:0xa, OCDN:0xa, ODTP:0xa, ODTN:0xa
DDR1866 PLL setting init
PCDDR3 AC Timing update
Fire MRW command...
ModeReg.2, value.0x20 done
Fire MRW command...
ModeReg.3, value.0x0 done
Fire MRW command...
ModeReg.1, value.0x6 done
Fire MRW command...
ModeReg.0, value.0x1114 done
Fire MRW command...
ModeReg.1, value.0x86 done
Fire MRW command...
ModeReg.1, value.0x6 done
Calculate size.
DRAM size=512MB
U-Boot 2014.04-rc1-svn104540 (Jan 14 2022 - 15:57:14)
DRAM:496 MiB
EN7529CU
Now running in RAM - U-Boot at: 9ee73000
spi_nand_probe: mfr_id=0x98, dev_id=0xcb
Using Flash ECC.
Detected SPI NAND Flash :_SPI_NAND_DEVICE_ID_TC58CVG1S3H, Flash Size=0x10000000
bmt pool size: 81
BMT & BBT Init Success
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
CPU0: found redistributor 0 region 0:9eeb3630
*** Warning - bad CRC, using default environment
Net: ecnt_eth
Uip activated
Not found TC Phy
fh_hwcfg: 0x77
Not found TC Phy
fh_hwcfg: 0x77
Not found TC Phy
fh_hwcfg: 0x77
Not found TC Phy
fh_hwcfg: 0x77
start fh_upg_upgrade!
multi pkg detect timeout!
Hit any key to stop autoboot:0
not find tclinux partition
fhdrv try get bootflag
fh_hwcfg: 0x77
fh_uart: 0xff
#####################################################
flag A kernel=0
flag A rootfs=0
flag A app = 0
flag A framework = 0
flag A crc = 0x90392a84
flag B kernel=0
flag B rootfs=0
flag B app = 0
flag B framework = 0
flag B crc = 0x90392a84
#####################################################
calculate crc32 value = 0x90392a84
Get flag info form FlagA partition
bootflag==0 --> booting from Main Image
get second image info.
get first image info.
Reading kernel...
bootargs init.
bootm flag=0, states=70f
## Loading kernel from FIT Image at 81800000 ...
Using 'conf@1' configuration
Trying 'kernel@1' kernel subimage
Description:ECONET Linux kernel
Type: Kernel Image
Compression:lzma compressed
Data Start: 0x8180206c
Data Size: 2815884 Bytes = 2.7 MiB
Architecture: ARM
OS: Linux
Load Address: 0x80088000
Entry Point:0x80088000
Hash algo: sha1
Hash value: ba08c6b2b156d28a1f3c6e95689d734c21741799
Verifying Hash Integrity ... sha1+ OK
## Loading fdt from FIT Image at 81800000 ...
Using 'conf@1' configuration
Trying 'fdt@1' fdt subimage
Description:ECONET Flattened Device Tree blob
Type: Flat Device Tree
Compression:uncompressed
Data Start: 0x818000f4
Data Size: 7935 Bytes = 7.7 KiB
Architecture: ARM
Verifying Hash Integrity ... OK
Booting using the fdt blob at 0x818000f4
Uncompressing Kernel Image ... OK
Loading Device Tree to 9ce66000, end 9ce6aefe ... OK
Starting kernel ...
Booting Linux on physical CPU 0x0
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Initializing cgroup subsys cpuacct
Linux version 4.4.115 (root@lzw-virtual-machine) (gcc version 4.9.3 (Buildroot 2015.08.1-gd814875) ) #1 SMP Fri Jan 14 16:16:47 CST 2022
CPU: ARMv7 Processor revision 4 (ARMv7), cr=10c5383d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: econet,en7523
bootconsole enabled
Memory policy: Data cache writealloc
psci: probing for conduit method from DT.
psci: PSCIv1.1 detected in firmware.
psci: Using standard PSCI v0.2 function IDs
psci: MIGRATE_INFO_TYPE not supported.
npu_pkt_buf_addr=9d4f1f80:9d4f1f80
npu_pkt_buffer memblock_alloc:9d4f1f80,buf_size=1600000
PERCPU: Embedded 11 pages/cpu @dd4d9000 s14016 r8192 d22848 u45056
Built 1 zonelists in Zone order, mobility grouping on.Total pages: 129472
Kernel command line: sdram_conf=0x00108893 vendor_name=ECONET Technologies Corp. product_name=xPON ONU ethaddr=00:AA:BB:01:23:40 snmp_sysobjid=1.2.3.4.5 country_code=ff ether_gpio=0c power_gpio=1515 dsl_gpio=0b internet_gpio=02 multi_upgrade_gpio=0b020400000000000000000000000000 onu_type=2 qdma_init=22 root=/dev/mtdblock4 ro rootfstype=squashfs console=ttyS0,115200n8 earlycon bootflag=0 tclinux_info=0x2b1b6c,0x406c,0x2af78c,0x20cc,0x1910abf,0x2b1b6c,0x406c,0x2af78c,0x20cc,0x1910abf
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 470372K/523008K available (5422K kernel code, 185K rwdata, 1532K rodata, 260K init, 621K bss, 52636K reserved, 0K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector: 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap: 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xe0800000 - 0xff800000 ( 496 MB)
lowmem: 0xc0000000 - 0xe0000000 ( 512 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbe800000 - 0xbfe00000 (22 MB)
.text : 0xc0088000 - 0xc0752c94 (6956 kB)
.init : 0xc0753000 - 0xc0794000 ( 260 kB)
.data : 0xc0794000 - 0xc07c2740 ( 186 kB)
.bss : 0xc07c5000 - 0xc0860560 ( 622 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
NR_IRQS:64 nr_irqs:64 64
CPU0: found redistributor 0 region 0:0x09080000
Architected cp15 timer(s) running at 25.00MHz (virt).
clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
Switching to timer-based delay loop, resolution 40ns
console enabled
console enabled
bootconsole disabled
bootconsole disabled
Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Initializing cgroup subsys io
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys debug
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x80088280 - 0x800882d8
CPU1: found redistributor 1 region 0:0x090a0000
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
Brought up 2 CPUs
SMP: Total of 2 processors activated (100.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
futex hash table entries: 512 (order: 3, 32768 bytes)
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 8 bytes.
l2c_sram_size:0x0
Initializing Ecnt Event Netlink Socket
Initializing Econet Event Netlink Socket nl_sk = dc8a7400
ecnt-hsdma 1fa01800.dma-controller: Econet HSDMA driver registered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 8
NET: Registered protocol family 20
clocksource: Switched to clocksource arch_sys_counter
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
sgmii probe init start
sgmii:int_name: sgmii_pcie0
sgmii:int_id: 0
sgmii:int_register: inin!
sgmii:sgmii->pcs1_base= e087c100
sgmii:sgmii->pcs2_base= e087ea00
sgmii:sgmii->an_base= e0944000
sgmii:sgmii->ra_base= e0946600
sgmii:sgmii->phya_base= e0948c00
sgmii:int_register: exit!
sgmii: int_init called
sgmii:cmd_wo:reg_t=e087ea20, val=0
sgmii: sync_int exit
sgmii probe init exit
sgmii probe init start
sgmii:int_name: sgmii_pcie1
sgmii:int_id: 1
sgmii:int_register: inin!
sgmii:sgmii->pcs1_base= e094a100
sgmii:sgmii->pcs2_base= e094ca00
sgmii:sgmii->an_base= e094e000
sgmii:sgmii->ra_base= e0950600
sgmii:sgmii->phya_base= e0952c00
sgmii:int_register: exit!
sgmii: int_init called
sgmii:cmd_wo:reg_t=e094ca20, val=0
sgmii: sync_int exit
sgmii probe init exit
sgmii probe init start
sgmii:int_name: sgmii_usb0
sgmii:int_id: 2
sgmii:int_register: inin!
sgmii:sgmii->pcs1_base= e0954100
sgmii:sgmii->pcs2_base= e0956a00
sgmii:sgmii->an_base= e0958000
sgmii:sgmii->ra_base= e095a600
sgmii:sgmii->phya_base= e095cc00
sgmii:int_register: exit!
sgmii: int_init called
sgmii:cmd_wo:reg_t=e0956a20, val=0
sgmii: sync_int exit
sgmii probe init exit
TC3162 hardware watchdog module loaded.
irq-0: 109 irq-1: 110 ecnt_i2c_drv_probe
res->name:/crypto_k@1fb70000
res->start:0x1fb70000 ===
res->end:0x1fb70803 ===
ecnt_crypto_k->base:0xe09dc000
ecnt_trng_drv_probe
test_uc:e0826000 test_c:dc8c0000 cpu_top->base:e09e6800
ecnt_timer_drv_probe
ecnt_timer->irq: 80
ecnt_timer->irq_soft_ratelimit: 77
res->name:/apb_timer1@1fbf0100
i2c_slave init(ecnt_i2c_slave_drv_probe) done
ecnt_i2s_drv_probe
7523 Thermal Sensor address probe done
squashfs: version 4.0 (2009/01/31) Phillip Lougher
ntfs: driver 2.1.32 .
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
io scheduler noop registered (default)
PCIe driver version: 7523.0.20210201
PCIe ref clk init.
===EN7523 PCIe init
mtk-pcie 1fa91000.pcie: Port0 link down
mtk-pcie 1fa91000.pcie: pcie rc 1 linkup success
===============PCIe check===tmp_reg=========81014c3===========
mtk-pcie 1fa91000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
pci_bus 0000:00: root bus resource
pci_bus 0000:00: root bus resource
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:00.0: bridge configuration invalid (), reconfiguring
pci 0000:00:01.0: bridge configuration invalid (), reconfiguring
PCI: bus1: Fast back to back transfers enabled
PCI: bus2: Fast back to back transfers disabled
pci 0000:00:01.0: BAR 8: assigned
pci 0000:00:00.0: PCI bridge to
{:6_183:}谢谢!!!!!!!!!!!!!
页:
[1]