zhjook 发表于 2021-11-25 13:22
捅菊花，开机，接ttl重置nvram就可以了
大佬 有没有相关的教程文档 或链接 我去参考学习一下
1531 发表于 2021-11-25 14:07
第一次学习 TTL模式，菊花是啥 ，是拆机的意思么
菊花就是光猫的复位键。
不懂，帮顶，来学习一下。
hutuch 发表于 2021-11-25 15:04
菊花就是光猫的复位键。
我还以为是后面的 螺丝啦！ 有涨知识了
牛人，语法不对，也敢执行
1531 发表于 2021-11-25 14:10
大佬 有没有相关的教程文档 或链接 我去参考学习一下
类似这样 ttl 进入cfe 命令模式之后
一般是 输入b 回车
就可以进入底层参数设置模式包括 CPUID ，mac 等等
img]https://www.chinadsl.net/forum.php?mod=attachment&aid=NTQ5NDN8ODc2NzllYzV8MTYzNzgyNjI4N3w0NTQ0NzF8MTA0MTQz&noupdate=yes
1531 发表于 2021-11-25 14:10
大佬 有没有相关的教程文档 或链接 我去参考学习一下
CFE version 1.0.37-106.24 for BCM96328 (32bit,SP,BE)
Build Date: ?????? ?????? 21 08:38:40 UTC 2012 (legath@desk)
Copyright (C) 2000-2009 Broadcom Corporation.
HS Serial flash device: name S25FL128, id 0x0118 size 16384KB
Total Flash size: 16384K with 256 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-6) : 96328avng
Number of MAC Addresses (1-32) : 12
Base MAC Address : 00:0a:c2:c3:fa:a7
PSI Size (1-64) KBytes : 48
Enable Backup PSI : 1
System Log Size (0-256) KBytes : 48
Main Thread Number : 0
Voice Board Configuration (0-11): VE890
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 110
Booting from latest image (0xb8800000) ...
Code Address: 0x80010000, Entry Address: 0x80014230
Decompression OK!
照片光模块右边的 J2 是TTL， 从上到下顺序是vcc
gnd
rx
tx
zhjook 发表于 2021-11-25 22:08
照片光模块右边的 J2 是TTL， 从上到下顺序是vcc
gnd
rx
TTL 显示 ，mac地址位数：显示只有11位 估计是这个位置错误导致无法启动，同时现在也无法进入 无法进入CFE ，一直重复如下：
BTRM
V1.0
R1.0
L1CD
MMUI
MMU9
DATA
ZBBS
MAIN
OTP?
OTPP
USBT
NAND
IMG?
IMGL
UHD?
UHDP
RLO?
RLOP
UBI?
UBIP
PASS
----
HELO
5.0205DW1-1.0.38-163.156
CPU0
L1CD
MMUI
MMUC
ZBBS
MAIN
Boot Strap Register:0x12008076
NVRAM memcfg 0x142f
MCB chksum 0x7a5e439d, config 0x142f
MemsysInit hpg0_generic_aarch64 3.5.1.1 20171009
DDR3
8262B278 80180000 801A0000 00000000 00000000 0010598A
MCB rev=0x00000501 Ref ID=0x0598A Sub Bld=0x001
Dram Timing 12-12-12
start of memsys_begin
mc_cfg_init(): Initialize the default values on mc_cfg
init_memc_dram_profile(): Initializing MEMC DRAM profile
---------------------------------------------------------------
MEMC DRAM profile (memc_dram_profile_struct) values:
====================================================
PART values:
part_speed_grade = 14
part_size_Mbits = 4096 (DRAM size in MegaBits)
part_row_bits = 15 (number of row bits)
part_col_bits = 10 (number of column bits)
part_ba_bits = 3 (number of bank bits)
part_width_bits = 16 (DRAM width in bits)
NUMER OF PARTS:
part_num = 1 (Number of parts)
TOTAL values:
total_size_Mbits = 4096 (DRAM size in MegaBits)
total_cs_bits = 0 (number of cs bits, for dual_rank mode)
total_width_bits = 16 (DRAM width in bits)
total_burst_bytes = 16 (Number of bytes per DRAM access)
total_max_byte_addr = 0x1fffffff (Maximum/last DRAM byte address)
(Number of bits in total_max_byte_addr is 29)
(i.e. total_max_byte_addr goes from bit 0 to bit 28)
ddr_2T_mode = 0
ddr_hdp_mode = 1
large_page = 1
ddr_dual_rank = 0
cs_mode = 0
MEMC timing (memc_dram_timing_cfg_struct) values:
====================================================
MC_CHN_TIM_TIM1_0 register fields:
tCwl = 9
tRP = 12
tCL = 12
tRCD = 12
MC_CHN_TIM_TIM1_1 register fields:
tCCD_L = 4
tCCD = 4
tRRD_L = 6
tRRD = 6
MC_CHN_TIM_TIM1_2 register fields:
tFAW = 33
tRTP = 7
tRCr = 44
MC_CHN_TIM_TIM1_3 register fields:
tWTR_L = 7
tWTR = 7
tWR_L= 14
tWR = 14
MC_CHN_TIM_TIM2 register fields:
tR2R = 0
tR2W = 2
tW2R = 2
tW2W = 0
tAL = 0
tRFC = 244
Poll PHY Status register
PHY Status= 1
Disable Auto-Refresh
refresh_ctrl_cfg writing to refresh control register (dram_clk_freq_MHz=933 ; ref_rate=0xd4 ; ref_disable=1)
= 0x8000d400
= 0x00000305
End of memsys_begin
Add/Ctl Alignment
Coarse Adj=0x087 deg, cmd steps=0x0AC
reg 0x801A0090 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A0094 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A0098 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A009C set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00A0 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00A4 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00A8 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00AC set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00B0 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00B4 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00B8 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00BC set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00C0 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00C4 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00C8 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00CC set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00D0 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00D4 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00D8 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00DC set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00E0 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00E4 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00E8 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00EC set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00F0 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00F4 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00F8 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A00FC set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A0100 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A0108 set to VDL 0x041 with Fine Adj=0x01 deg
reg 0x801A010C set to VDL 0x041 with Fine Adj=0x01 deg
HP RX TRIM
itrim = 0x0
lstrim = 0x9
ZQ Cal HP PHY
R in Ohm
P: Finger=0x364 Term=0x7C Drv=0x27
N: Finger=0x336 Term=0x75 Drv=0x27
PLL Ref(Hz)=0x02FAF080 UI STEPS=0x056
DDR CLK(MHz)=0x39F WL CLK dly(ps)=0x0C8 bitT(ps)=0x21B VDLsize(fs)=0x187B CLK_VDL=0x020
start of memc_init
= 0x0110061f
= 0x00001101
Enable Auto-Refresh
refresh_ctrl_cfg writing to refresh control register (dram_clk_freq_MHz=933 ; ref_rate=0xd4 ; ref_disable=0)
= 0x0000d400
= 0x11100f0e
= 0x15141312
= 0x19181716
= 0x001c1b1a
= 0x04000000
= 0x08070605
= 0x00000a09
= 0x000d0c0b
Writing to MC_CHN_CFG_CNFG reg; data=0x00000000
= 0x00000000
cfg_memc_timing_ctrl() Called
= 0x090c0c0c
= 0x04040606
= 0x2100072c
= 0x07070e0e
= 0x120000f4
End of memc_init
start of pre_shmoo
= 0xc110071f
end of pre_shmoo
SHMOO 28nm
801A0000 80180800 00000000 00020000 00000000
Shmoo WL
One UI Steps : 0x61
disable_dram_refresh
refresh_ctrl_cfg writing to refresh control register (dram_clk_freq_MHz=933 ; ref_rate=0xd4 ; ref_disable=1)
= 0x8000d400
auto-clk result = 00B (filter=0C steps)
initial CLK shift = 020
final CLK shift = 00B
disable_dram_refresh
refresh_ctrl_cfg writing to refresh control register (dram_clk_freq_MHz=933 ; ref_rate=0xd4 ; ref_disable=1)
= 0x8000d400
enable_dram_refresh
refresh_ctrl_cfg writing to refresh control register (dram_clk_freq_MHz=933 ; ref_rate=0xd4 ; ref_disable=0)
= 0x0000d400
0000000000111111111122222222223333333333444444444455555555556666666666777777777788888888889999999
0123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456
00 S------------X-----------------------------------------------------------------------------------
01 S------------------------X-----------------------------------------------------------------------
Shmoo RD En
FORCED WR ODT = 0x00001800
DQSN DRIVE PAD CONTROL (from) (to)
B0 00039ED5 00079ED5
B1 00039ED5 00079ED5
B0 RISE UI=1 VDL=3F PICK UI=2 VDL=3F
B1 RISE UI=1 VDL=23 PICK UI=2 VDL=23
0000000000111111111122222222223333333333444444444455555555556666666666777777777788888888889999999
0123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456
00 --S------------------------------------------------------------X+++++++++++++++------------------
01 --S--------------------------------X+++++++++++++++----------------------------------------------
Shmoo RD DQ NP
DQS :
B0 VDL=56 ok
B1 VDL=56 ok
0000000000111111111122222222223333333333444444444455555555556666666666777777777788888888889999999
0123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456
00 -----------------------++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++
01 -----------------------++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++
02 ----------------------+++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++
03 --------------------++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++---
04 --------------------++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++---
05 ----------------+++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++-----
06 -------------------+++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++--
07 -----------------+++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++-----
08 --------------------+++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++-
09 ----------------+++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++-----
10 ------------------+++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++---
11 --------------++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++------
12 ------------------+++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++---
13 ------------++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++-----------
14 -----------------+++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++-----
15 -------------++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++------
Shmoo RD DQ P
0000000000111111111122222222223333333333444444444455555555556666666666777777777788888888889999999
0123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456
00 -----------------------++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++
01 -----------------------++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++
02 ----------------------+++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++
03 --------------------++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++---
04 --------------------+++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++--
05 ----------------++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++----
06 -------------------++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++-
07 ----------------+++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++-----
08 ---------------------+++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++-
09 ----------------+++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++-----
10 ------------------+++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++---
11 --------------++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++------
12 ------------------++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++--
13 -----------+++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++----------
14 ----------------++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++---
15 -------------+++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++-----
Shmoo RD DQ N
0000000000111111111122222222223333333333444444444455555555556666666666777777777788888888889999999
0123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456
00 --------------------++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++
01 ---------------------+++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++
02 --------------------++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++
03 -----------------++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++--
04 ------------------+-++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++---
05 -------------+++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++-----
06 ------------------+++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++---
07 --------------+++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++----
08 ---------------++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++-
09 ------------++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++----
10 ---------------+++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++---
11 ----------++++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++------
12 --------------+++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++---
13 --------++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++-----------
14 -------------+++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++-----
15 -----------+++++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++++++------
RD DQS adjustments :
BL0: Start: 0x56 Final: 0x56
BL1: Start: 0x56 Final: 0x56
Shmoo WR DQ
0000000000111111111122222222223333333333444444444455555555556666666666777777777788888888889999999
0123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456
00 ----------------++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++------------
01 ----------------++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++-------
02 -------------------+++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++----------
03 ----------------++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++------------
04 ----------------++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++-----------
05 ------------+++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++-------------
06 -----------------++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++----------
07 ------------+++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++-------------
08 -----------++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++------------
09 --------++++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++----------------
10 -----------++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++----------------
11 -------+++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++-------------------
12 ----------+++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++----------------
13 --++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++-------------------------
14 -----++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++------------------
15 ----+++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++---------------------
Shmoo WR DM
WR DM
0000000000111111111122222222223333333333444444444455555555556666666666777777777788888888889999999
0123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123456
00 ---------------+++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++----------
01 ---+++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++++----------------------
start of memsys_end
= 0x8110071f
= 0x00000009
end of memsys_end
DDR test done successfully
FPS0
----
PAR1
U998
COM0
UBI#
03E6
BT98
0008
----
PAR2
U999
COM1
UBI#
03E7
BT99
0496
----
TRY2
NAN3
UBI!
NAN5
Base: 5.2_05DW1
CFE version 1.0.38-163.156 for BCM96856 (64bit,SP,LE)
Build Date: Wed Jan 15 17:21:31 CST 2020 (publisher@publisher.rd.scty)
Copyright (C) 2000-2015 Broadcom Corporation.
Boot Strap Register:0x12008076
Chip ID: BCM68560_B1, Broadcom B53 Dual Core: 1500MHz
RDP: 1400MHz
Total Memory: 536870912 bytes (512MB)
Status wait timeout: nandsts=0x10000000 mask=0x40000000, count=0
NAND ECC BCH-8, page size 0x800 bytes, spare size used 108 bytes
NAND flash device: Micron MT29F2G08ABA, id 0x2cda block 128KB size 262144KB
CPU1
Take PMC out of reset
waiting for PMC finish booting
PMC rev: 3.1.9.427360 running
Dump Current setting of SWREGs
1.0D, reg=0x00, val=0xc690
1.0D, reg=0x01, val=0x0d06
1.0D, reg=0x02, val=0xcb12
1.0D, reg=0x03, val=0x5372
1.0D, reg=0x04, val=0x0000
1.0D, reg=0x05, val=0x0702
1.0D, reg=0x06, val=0xa300
1.0D, reg=0x07, val=0x0029
1.0D, reg=0x08, val=0x0c02
1.0D, reg=0x09, val=0x0071
1.8 , reg=0x00, val=0xc690
1.8 , reg=0x01, val=0x0d06
1.8 , reg=0x02, val=0xcb12
1.8 , reg=0x03, val=0x5370
1.8 , reg=0x04, val=0x0000
1.8 , reg=0x05, val=0x0702
1.8 , reg=0x06, val=0xb000
1.8 , reg=0x07, val=0x0029
1.8 , reg=0x08, val=0x0c02
1.8 , reg=0x09, val=0x0071
1.5 , reg=0x00, val=0xc690
1.5 , reg=0x01, val=0x0d06
1.5 , reg=0x02, val=0xcb12
1.5 , reg=0x03, val=0x5370
1.5 , reg=0x04, val=0x0000
1.5 , reg=0x05, val=0x0702
1.5 , reg=0x06, val=0xb000
1.5 , reg=0x07, val=0x0029
1.5 , reg=0x08, val=0x0c02
1.5 , reg=0x09, val=0x0071
1.0A, reg=0x00, val=0xc690
1.0A, reg=0x01, val=0x0d06
1.0A, reg=0x02, val=0xcb12
1.0A, reg=0x03, val=0x5370
1.0A, reg=0x04, val=0x0000
1.0A, reg=0x05, val=0x0702
1.0A, reg=0x06, val=0xb000
1.0A, reg=0x07, val=0x0029
1.0A, reg=0x08, val=0x0c02
1.0A, reg=0x09, val=0x0071
pmc_init:PMC using DQM mode
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host/tftp (f/h/c): f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Default host ramdisk file name :
Default ramdisk store address :
Default DTB file name :
Board Id : TY968560D9CT
Number of MAC Addresses (1-64) : 11
Base MAC Address : c4:a1:51:0c:d8:cc
PSI Size (1-512) KBytes : 24
Enable Backup PSI : 1
System Log Size (0-256) KBytes : 0
Auxillary File System Size Percent: 0
GPON Serial Number : "XX"
GPON Password : " "
RNR_TBLS memory allocation (8-13) (MB) : 8
FPM_POOL memory allocation (MB) : 32
DHD 0 memory allocation (MB) : 0
DHD 1 memory allocation (MB) : 0
DHD 2 memory allocation (MB) : 0
WLan Feature : 0x00
Voice Board Configuration (0-2) : SI32192_ISI_CB
Partition 1 Size (MB) : 128M
Partition 2 Size (MB) : 0M
Partition 3 Size (MB) : 0M
Partition 4 Size (MB) (Data) : 4M
*** Press 'ty' to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from latest image (address 0x03e00000, flash offset 0x03e00000) ...
ubi_find_file: got vmlinux.lzsize 2818667
Decompression LZMA Image OK!
Entry at 0x0000000000080000
Starting program at 0x0000000000080000
ubi_find_file: got 96856.dtbsize 2905
/memory = 0x20000000 bytes @ 0x0
Appending CFE version to dtb, ret:0
Appending NVRAM to dtb, ret:0
Booting Linux on physical CPU 0x0
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Initializing cgroup subsys cpuacct
Linux version 4.1.51 (publisher@publisher.rd.scty) (gcc version 5.5.0 (Buildroot 2017.11.1) ) #2 SMP PREEMPT Wed Jan 15 17:29:53 CST 2020
CPU: AArch64 Processor revision 0
Detected VIPT I-cache on CPU0
alternatives: enabling workaround for ARM erratum 845719
PERCPU: Embedded 16 pages/cpu @ffffffc01ffd5000 s24792 r8192 d32552 u65536
Built 1 zonelists in Zone order, mobility grouping on.Total pages: 118944
Kernel command line: coherent_pool=4M cpuidle_sysfs_switch pci=pcie_bus_safe
PID hash table entries: 2048 (order: 2, 16384 bytes)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Memory: 456452K/483328K available (4723K kernel code, 1053K rwdata, 1912K rodata, 212K init, 444K bss, 26876K reserved, 0K cma-reserved)
Virtual kernel memory layout:
vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000 ( 246 GB)
vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum)
0xffffffbdc0000000 - 0xffffffbdc0800000 ( 8 MB actual)
fixed : 0xffffffbffabfd000 - 0xffffffbffac00000 ( 12 KB)
PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000 ( 16 MB)
modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
memory: 0xffffffc000000000 - 0xffffffc020000000 ( 512 MB)
.init : 0xffffffc0006fc000 - 0xffffffc000731000 ( 212 KB)
.text : 0xffffffc000080000 - 0xffffffc0006fb694 (6638 KB)
.data : 0xffffffc000732000 - 0xffffffc0008396e0 (1054 KB)
Preemptible hierarchical RCU implementation.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
NR_IRQS:64 nr_irqs:64 0
Architected cp15 timer(s) running at 50.00MHz (phys).
clocksource arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb8812736b, max_idle_ns: 440795202655 ns
sched_clock: 56 bits at 50MHz, resolution 20ns, wraps every 4398046511100ns
BRCM Legacy Drivers' Helper, all legacy drivers' IO memories/interrupts should be remapped here
Remapping interrupts...
hwirq virq
61 5
64 6
65 7
125 8
92 9
93 10
94 11
43 12
44 13
45 14
46 15
213 16
214 17
215 18
216 19
217 20
218 21
219 22
220 23
70 24
116 25
131 26
130 27
137 28
138 29
139 30
160 31
161 32
162 33
163 34
164 35
165 36
166 37
167 38
168 39
169 40
170 41
171 42
172 43
173 44
174 45
175 46
176 47
177 48
178 49
179 50
180 51
181 52
182 53
183 54
184 55
185 56
186 57
187 58
188 59
189 60
190 61
191 62
146 63
153 64
156 65
157 66
154 67
155 68
Remapping IO memories...
phys virt size
0000000080180000ffffff800004000000024000
00000000ffb00000ffffff800000800000006000
00000000ffb20000ffffff800000200000001000
0000000082000000ffffff800008000001000000
0000000083000000ffffff800001000000001000
00000000ff800000ffffff800001400000003000
00000000ff854000ffffff800001200000001000
00000000ff858000ffffff800001800000004000
00000000ffe00000ffffff800110000000100000
00000000ff860000ffffff800002000000002000
0000000083058600ffffff800001e60000000100
0000000082db2000ffffff800002400000001000
0000000082db4000ffffff80000300000000e000
000000008000c000ffffff800002800000003fff
000000008300c000ffffff800002600000001000
0000000083028000ffffff800002e00000001000
0000000083020000ffffff800006600000001000
0000000083038000ffffff800006800000001000
0000000083058000ffffff800006a00000001000
0000000083064000ffffff800006c00000001000
0000000083068000ffffff800006e00000001000
0000000083080000ffffff800007000000001000
0000000083088000ffffff800007200000001000
00000000830a0000ffffff800007400000001000
00000000830a4000ffffff800007600000001000
00000000830ac000ffffff800007800000001000
00000000810a0000ffffff800007a00000001000
0000000081060000ffffff800007c00000003000
console enabled
Calibrating delay loop (skipped), value calculated using timer frequency.. 100.00 BogoMIPS (lpj=500000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes)
--Kernel Config--
SMP=1
PREEMPT=1
DEBUG_SPINLOCK=0
DEBUG_MUTEXES=0
Initializing cgroup subsys blkio
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
creating mapping for reserved memory phys 0x0e000000 virt 0xffffffc00e000000 size 0x02000000 for fpm_pool
creating mapping for reserved memory phys 0x0d800000 virt 0xffffffc00d800000 size 0x00800000 for rnr_tbls
pmc_init:PMC using DQM mode
Successfully retrieved NVRAM data from dtb
cfe-v: 1.0.38-163.156
CPU1: Booted secondary processor
Detected VIPT I-cache on CPU1
Brought up 2 CPUs
SMP: Total of 2 processors activated.
CPU: All CPU(s) started at EL2
alternatives: patching kernel code
devtmpfs: initialized
clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
futex hash table entries: 512 (order: 3, 32768 bytes)
NET: Registered protocol family 16
cpuidle: using governor ladder
cpuidle: using governor menu
Toggle reset of XRDP core...
Toggle reset of XRDP core...
vdso: 2 pages (1 code @ ffffffc000739000, 1 data @ ffffffc000738000)
DMA: preallocated 4096 KiB pool for atomic allocations
Broadcom Logger v0.1
ACPI: Interpreter disabled.
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
bcmhs_spi bcmhs_spi.1: master is unqueued, this is deprecated
skb_free_task created successfully with start budget 256
gbpm_do_work scheduled
BLOG v3.0 Initialized
BLOG Rule v1.0 Initialized
Broadcom IQoS v1.0 initialized
Switched to clocksource arch_sys_counter
pnp: PnP ACPI: disabled
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2. (NAND) (SUMMARY)© 2001-2006 Red Hat, Inc.
fuse init (API version 7.23)
io scheduler noop registered (default)
brd: module loaded
loop: module loaded
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
bcm63xx_nand ff801800.nand: Adjust timing_1 to 0x6532845b timing_2 to 0x00091e94
bcm63xx_nand ff801800.nand: detected 256MiB total, 128KiB blocks, 2KiB pages, 27B OOB, 8-bit, BCH-8
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
>>>>> For primary mtd partition rootfs, cferam/vmlinux.lz UBI volume, vmlinux fs mounted as squash fs on UBI <<<<<
Secondary mtd partition rootfs_update detected as UBI for cferam/vmlinux source and squash fs on UBI for vmlinux filesystem
extra max size:8000000
Creating 10 MTD partitions on "brcmnand.0":
0x000003e00000-0x000007b00000 : "rootfs"
0x000000100000-0x000003e00000 : "rootfs_update"
0x00000fb00000-0x00000ff00000 : "data"
0x000000000000-0x000000100000 : "nvram"
0x000000100000-0x000003e00000 : "image_update"
0x000003e00000-0x000007b00000 : "image"
0x000007b00000-0x00000fb00000 : "saf"
0x000007b00000-0x000008700000 : "frwk1"
0x000008700000-0x000009300000 : "frwk2"
0x000009300000-0x00000fb00000 : "apps"
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usbserial
usbcore: registered new interface driver ch341
usbserial: USB Serial support registered for ch341-uart
usbcore: registered new interface driver cp210x
usbserial: USB Serial support registered for cp210x
usbcore: registered new interface driver ftdi_sio
usbserial: USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver option
usbserial: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver pl2303
usbserial: USB Serial support registered for pl2303
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
brcmboard registered
brcmboard: brcm_board_init entry
set_location_info: init location code:0x3300
print_rst_status: Last RESET due to Unknown
print_rst_status: RESET reason: 0x00000000
DYING GASP IRQ Initialized and Enabled
map_hw_timer_interrupt,127: interrupt_id 12
map_hw_timer_interrupt,127: interrupt_id 13
map_hw_timer_interrupt,127: interrupt_id 14
map_hw_timer_interrupt,127: interrupt_id 15
id:1
id:1
id:1
id:1
id:1
hw_id:1f
Serial: BCM63XX driver $Revision: 3.00 $
Magic SysRq with Auxilliary trigger char enabled (type ^ h for list of supported commands)
ttyS0 at MMIO 0xff800640 (irq = 6, base_baud = 921600) is a BCM63XX
ttyS1 at MMIO 0xff800660 (irq = 7, base_baud = 921600) is a BCM63XX
i2c-bcm63000 ff802100.i2c: Broadcom BCM96xxx I2C driver
bcm_i2c: prepare_sfp_detection i2c bus 0 sfp detection using interrupt on gpio 23
bcm_i2c: probe_sfp_sff i2c device at address 0x50 detected
bcm_i2c: probe_sfp_sff i2c device at address 0x51 detected
Opticaldet: optical module detected on i2c bus 0:
Opticaldet: Illegal TRX type 255
Optical detection module loaded.
GACT probability NOT on
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
ip6_gre: GRE over IPv6 tunneling driver
NET: Registered protocol family 17
bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
L2TP core: blog_l2tp_rcv_check
l2tp_core: L2TP core driver, V2.0
l2tp_ppp: PPPoL2TP kernel driver, V2.0
8021q: 802.1Q VLAN Support v1.8
ubi0: attaching mtd0
ubi0: scanning is finished
ubi0: attached mtd0 (name "rootfs", size 61 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 488, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 4, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1412928644
ubi0: available PEBs: 0, total reserved PEBs: 488, PEBs reserved for bad PEB handling: 1
ubi0: background thread "ubi_bgt0d" started, PID 390
VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
devtmpfs: mounted
Freeing unused kernel memory: 212K
init started: BusyBox v1.28.3 (2020-01-15 17:35:00 CST)
starting pid 420, tty '': '/bin/sh -l -c "bcm_boot_launcher start"'
Mounting filesystems...
>>>>> Starting mdev <<<<<
>>>>> Creating static device nodes <<<<<
>>>>> Mounting /data partition <<<<<
get mtd 'usrex' info failed
jffs2: Empty flash at 0x00278004 ends at 0x00278800
jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x00278fd8: Read 0xffffffff, calculated 0x9c10f1f9
jffs2: notice: (550) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Configuring system...
mkdir: can't create directory '/opt/upt/apps/probe/': Read-only file system
makedir /opt/upt/apps/probe/ succeed failed
mkdir: can't create directory '/opt/upt/apps/probe/lib/': No such file or directory
makedir /opt/upt/apps/probe/lib/ failed
mkdir: can't create directory '/opt/upt/apps/probe/tool/': No such file or directory
makedir /opt/upt/apps/probe/tool/ failed
mkdir: can't create directory '/opt/upt/apps/probe/boot/': No such file or directory
makedir /opt/upt/apps/probe/boot/ failed
mkdir: can't create directory '/opt/upt/apps/probe/curl/': No such file or directory
makedir /opt/upt/apps/probe/curl/ failed
/opt/scripts/loader.sh: cd: line 497: can't cd to /opt/upt/apps/probe/lib/: No such file or directory
start download curl
/opt/scripts/loader.sh: cd: line 497: can't cd to /opt/upt/apps/probe/curl/: No such file or directory
start download curlinfo
rm: can't remove '/opt/upt/apps/probe/curl/curl.info': No such file or directory
download curl from http://10.0.0.23:9992/GetCurl/curl.info
/opt/scripts/loader.sh: cd: line 497: can't cd to /opt/upt/apps/probe/curl/: No such file or directory
Connecting to 10.0.0.23:9992 (10.0.0.23:9992)
wget: can't connect to remote host (10.0.0.23): Network is unreachable
Loading drivers and kernel modules...
bcm_pondrv: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
RDPA_MW: scratchpad get_or_init: WanRate - 1025
RDPA_MW: scratchpad get_or_init: RdpaWanType - XGPON1
fpm base =0xffffffc00e000000 fpm poolsize 33554432, MTU: 1536, token: 512 rnr_tables=0xffffffc00d800000 size=8388608
INFO: _data_path_init#2139: Start.
INFO: _data_path_init#2149: Driver init.
FPM driver: base 0xffffffc00e000000; buffer size 512
INFO: _data_path_init#2171: EnCreating CPU ring for queue number 17 with 16384 packets descriptor=0xffffffbffc512ab8, size_of_entry 8
Done initializing Ring 17 Base=0xffffffc01dac0000 num of entries= 16384 RDD Base=1dac0000 descriptor=0xffffffbffc512ab8
Creating CPU ring for queue number 18 with 16384 packets descriptor=0xffffffbffc512b30, size_of_entry 8
Done initializing Ring 18 Base=0xffffffc01d5c0000 num of entries= 16384 RDD Base=1d5c0000 descriptor=0xffffffbffc512b30
Creating CPU ring for queue number 16 with 2048 packets descriptor=0xffffffbffc512a40, size_of_entry 8
able Accelerators.
INFO:Done initializing Ring 16 Base=0xffffffc01dab8000 num of entries= 2048 RDD Base=1dab8000 descriptor=0xffffffbffc512a40
_data_path_init#2173: End.
Bridge fastpath module
brcmchipinfo: brcm_chipinfo_init entry
NBUFF v1.0 Initialized
npe_max_ent<32768> npe_ht_ent<8192>
Total # of labels = 66
Initialized fcache state
Broadcom Packet Flow CacheChar Driver v4.0 Registered<3002>
fc_timer_task created successfully
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Broadcom Packet Flow Cache learning via BLOG enabled.
pktDbgLvl=0
fhw_construct:
Initialized Fcache HW accelerator layer state
flwStatsThread created. numFlwsPerPoll 546 maxFlwIdx 16383
Fcache Pathstats created
Constructed Broadcom Packet Flow Cache v4.0
Creating CPU ring for queue number 4 with 1024 packets descriptor=0xffffffbffc5124a0, size_of_entry 16
Done initializing Ring 4 Base=0xffffffc01a208000 num of entries= 1024 RDD Base=1a208000 descriptor=0xffffffbffc5124a0
Creating CPU ring for queue number 3 with 1024 packets descriptor=0xffffffbffc512428, size_of_entry 16
Done initializing Ring 3 Base=0xffffffc01a090000 num of entries= 1024 RDD Base=1a090000 descriptor=0xffffffbffc512428
Creating dynamic meter on cpu/index=0 queue 3
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
IPTV ddr base addr: 0x000000001a1e0000
IPTV virtual ddr base addr: ffffffc01a1e0000
Retrieve num_fhw_path=32
Broadcom Packet Flow Cache HW acceleration enabled.
Retrieve num_fhw_path=32
Broadcom Packet Flow Cache HW acceleration enabled.
Initializing WLCSM Module
WLCSM Module loaded successfully
download curl from http://10.0.0.23:9992/GetCurl/curl.info
/opt/scriPCIe HCD (impl1)
pts/loader.sh: cd: line 497: can't cd to /opt/upt/apps/probe/curl/: No such file or directory
Connecting to 10.0.0.23:9992 (10.0.0.23:9992)
wget: can't connect to remobcm963xx-pcie: found port GEN2 Core Rev with 1 Lanes
te host (10.0.0.23): Network is unreachable
bcm963xx-pcie: core Link UP - lanes, speed
bcm963xx-pcie bcm963xx-pcie.0: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource
pci_bus 0000:00: root bus resource
bcm963xx-pcie: Core Enabled PCIE/UBUS Error Interrupts
bcm963xx-pcie: Core UBUS Intr
pci 0000:00:00.0: of_irq_parse_pci() failed with rc=-22
pci 0000:00:00.0: bridge configuration invalid (), reconfiguring
pci 0000:01:00.0: of_irq_parse_pci() failed with rc=-22
pci 0000:00:00.0: BAR 8: assigned
pci 0000:01:00.0: BAR 2: assigned
pci 0000:01:00.0: BAR 0: assigned
pci 0000:00:00.0: PCI bridge to
pci 0000:00:00.0: bridge window
pcieport 0000:00:00.0: enabling device (0000 -> 0002)
pcieport 0000:00:00.0: Max Payload Size set to512/ 512 (was128), Max Read Rq512
pci 0000:01:00.0: Max Payload Size set to512/ 512 (was128), Max Read Rq512
bcm963xx-pcie: found port GEN2 Core Rev with 1 Lanes
download curl from http://10.0.0.23:9992/GetCurl/curl.info
/opt/scripts/loader.sh: cd: line 497: can't cd to /opt/upt/apps/probe/curl/: No such file or directory
Connecting to 10.0.0.23:9992 (10.0.0.23:9992)
wget: can't connect to remote host (10.0.0.23): Network is unreachable
bcm963xx-pcie: core Link UP - lanes, speed
bcm963xx-pcie bcm963xx-pcie.1: PCI host bridge to bus 0001:00
pci_bus 0001:00: root bus resource
pci_bus 0001:00: root bus resource
bcm963xx-pcie: Core Enabled PCIE/UBUS Error Interrupts
bcm963xx-pcie: Core UBUS Intr
pci 0001:00:00.0: of_irq_parse_pci() failed with rc=-22
pci 0001:00:00.0: bridge configuration invalid (), reconfiguring
pci 0001:01:00.0: of_irq_parse_pci() failed with rc=-22
pci 0001:00:00.0: BAR 8: assigned
pci 0001:01:00.0: BAR 0: assigned
pci 0001:00:00.0: PCI bridge to
pci 0001:00:00.0: bridge window
pcieport 0001:00:00.0: enabling device (0000 -> 0002)
pcieport 0001:00:00.0: Max Payload Size set to128/ 512 (was128), Max Read Rq512
pci 0001:01:00.0: Max Payload Size set to128/ 128 (was128), Max Read Rq512
bcm963xx-pcie: found port GEN2 Core Rev with 1 Lanes
bcm963xx-pcie: core link is DOWN
bcm963xx-pcie: core powered down
Wifi Forwarding Driver is initialized!
dsphal_init: Starting DSPHAL driver.
Configuring PCM bus mux
pcm_clk_init: starting PCM clock
pcm_nco_init: PCM clock in ISI mode
pcm_nco_init: loading MISC FCW to PCM NCO: 0xa7c5ac47
dh_configure_channel: device 0, channel 0, id 0, devType 22, intfType 0, status 0, chanType 0, rate 8000 Hz, comp 0
pcm_config_channel: channel 0
pcm_ts_alloc: DMA timeslot assigned to PCM channel 0
pcm_ts_alloc: DMA timeslot assigned to PCM channel 0
dh_configure_channel: ignoring non-active device 0 channel 1
cat /opt/upt/apps/probe/curl/curl.info
cat: can't open '/opt/upt/apps/probe/curl/curl.info': No such file or directory
download curl from http://10.0.0.23:9993/GetCurl/curl.tar.gz
/opt/scripts/loader.sh: cd: line 497: can't cd to /opt/upt/apps/probe/lib slicslac_init: Starting SLIC/SLAC driver.
/: No such file or directory
Connecting to 10.0.0.23:9993 (10.0.0.23:9993)
wget: can't connect to remote host (10.0.0.23): Network is unreachable
md5sum ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
/opt/upt/apps/probe/lib/curl.tar.gz
md5sum: can't open '/opt/upt/apps/probe/lib/curl.tar.gz': No such fehci-platform: EHCI generic platform driver
ile or directehci-pci: EHCI PCI platform driver
ory
kkk
correct curl.tar.gz
tar: canohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
't open '/optohci-platform: OHCI generic platform driver
/upt/apps/proohci-pci: OHCI PCI platform driver
be/lib/curl.tar.gz': No such file or directory
++++ Powering up USB blocks
xhci-hcd xhci-hcd.0: xHCI Host Controller
xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 1
xhci-hcd xhci-hcd.0: hcc params 0x0250f17d hci version 0x100 quirks 0x00014010
xhci-hcd xhci-hcd.0: irq 64, io mem 0x8000d000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
xhci-hcd xhci-hcd.0: xHCI Host Controller
xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ehci-platform ehci-platform.0: EHCI Host Controller
ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 3
ehci-platform ehci-platform.0: irq 66, io mem 0x8000c300
ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
ohci-platform ohci-platform.0: Generic Platform OHCI controller
ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 4
ohci-platform ohci-platform.0: irq 65, io mem 0x8000c400
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
ehci-platform ehci-platform.1: EHCI Host Controller
ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 5
ehci-platform ehci-platform.1: irq 68, io mem 0x8000c500
ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 1 port detected
ohci-platform ohci-platform.1: Generic Platform OHCI controller
ohci-platform ohci-platform.1: new USB bus registered, assigned bus number 6
ohci-platform ohci-platform.1: irq 67, io mem 0x8000c600
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 1 port detected
usbcore: registered new interface driver usblp
usbcore: registered new interface driver usb-storage
usbcore: registered new interface driver uas
Broadcom 802.1Q VLAN Interface, v0.1
i2s registered
nf_conntrack version 0.5.0 (8192 buckets, 65536 max)
MAXNET DPI interface Loaded
Loading GRE kernel modules...
gre: GRE over IPv4 demultiplexor driver
ip_gre: GRE over IPv4 tunneling driver
mounting cgroup...
get mtd 'apps' info success
DEVNAME:mtd9
MAJOR:90
MINOR:18
attaching mtd apps(mtd9)...
ubi1: attaching mtd9
download curl from http://10.0.0.23:9993/GetCurl/curl.tar.gz
/opt/scripts/loader.sh: cd: line 497: can't cd to /opt/upt/apps/probe/lib/: No such file or directory
Connecting to 10.0.0.23:9993 (10.0.0.23:9993)
wget: can't connect to remote host (10.0.0.23): Network is unreachable
md5sum /opt/upt/apps/probe/lib/curl.tar.gz
md5sum: can't open '/opt/upt/apps/probe/lib/curl.tar.gz': No such file or directory
kkk
correct curl.tar.gz
tar: can't open '/opt/upt/apps/probe/lib/curl.tar.gz': No such file or directory
ubi1: scanning is finished
ubi1: attached mtd9 (name "apps", size 104 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 832, bad PEBs: 0, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 7/3, WL threshold: 4096, image sequence number: 2706998041
ubi1: available PEBs: 0, total reserved PEBs: 832, PEBs reserved for bad PEB handling: 1
ubi1: background thrUBI deviceead "ubi_bgt1d" started, PID 1259
number 1, total 832 LEBs (105644032 bytes, 100.8 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
attached mtd9 to ubi1
MAJOR:250
MINOR:0
Volume ID: 0 (on ubi1)
Type: dynamic
Alignment: 1
Size: 827 LEBs (105009152 bytes, 100.1 MiB)
State: OK
Name: apps
CharacteUBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 1303
r device major/minor: 250:1
mounting ubi volume 'apps' to /opt/upt/apps...
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "apps"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 103612416 bytes (98 MiB, 816 LEBs), journal size 5206016 bytes (4 MiB, 41 LEBs)
UBIFS (ubi1:0): reserved for root: 4893869 bytes (4779 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 79B380D4-4FB3-491D-ABDA-4FA94488DB75, small LPT model
no modules list in nvram, using defaults...
loading WLAN kernel modules ... wlemf wl dhd wlct
download curl from http://10.0.0.23:9993/GetCurl/curl.tar.gz
/opt/scripts/loader.sh: cd: line 497: can't cd to /opt/upt/apps/probe/lib/: No such file or directory
Connecting to 10.0.0.23:9993 (10.0.0.23:9993)
wget: can't connect to remote host (10.0.0.23): Network is unreachable
md5sum /opt/upt/apps/probe/lib/curl.tar.gz
md5sum: can't open '/opt/upt/apps/probe/lib/curl.tar.gz': No such file or directory
kkk
correct curl.tar.gz
tar: can't open '/opt/upt/apps/probe/lib/curl.tar.gz': No such file or directory
--SMP support
wl: dsl_tx_pkt_flush_len=338
wl: norm_wmark_tot=400, pktc_wmark_tot=2048
wl 0001:01:00.0: enabling device (0000 -> 0002)
wl: passivemode=1
wl0: creating kthread wl0-kthrd
initvars_cis_pci: Not CIS format
Neither SPROM nor OTP has valid image
wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
wl: pszBoardId: TY968560D9CT, ucHwBoardId: 0x1f, FEM BoardId: RTC5638H
wl: ID=pci/1/1/0/
wl: BoardId: _TY968560D9CT_RTC5638H, chipId: a8d1
pcid:0
wl: ready to read file: /etc/wlan/bcm43217_TY968560D9CT_RTC5638H_map.bin
wl: ID=pci/1/1/0/
wl: BoardId: _TY968560D9CT, chipId: a8d1
pcid:0
wl: ready to read file: /etc/wlan/bcm43217_TY968560D9CT_map.bin
wl: loading /etc/wlan/bcm43217_TY968560D9CT_map.bin
srom rev:8
wl: reading /etc/wlan/bcm43217_nvramvars.bin
Apply NVRAMVARS:/etc/wlan/bcm43217_nvramvars.bin
wl0: allocskbmode=1 currallocskbsz=1024
Creating CPU ring for queue number 7 with 1024 packets descriptor=0xffffffbffc512608, size_of_entry 16
Done initializing Ring 7 Base=0xffffffc0192a8000 num of entries= 1024 RDD Base=192a8000 descriptor=0xffffffbffc512608
Creating CPU ring for queue number 8 with 1024 packets descriptor=0xffffffbffc512680, size_of_entry 16
Done initializing Ring 8 Base=0xffffffc0192b0000 num of entries= 1024 RDD Base=192b0000 descriptor=0xffffffbffc512680
wfd_bind: Dev wl%d wfd_idx 0 wl_radio_idx 0 Type skb configured WFD thread wfd0-thrd minQId/maxQId (0/1), status (0) qmask 0x3
Instantiating WFD 0 thread
wfd_registerdevice Successfully registered dev wl0 ifidx 0 wfd_idx 0
wl0: Broadcom BCM43227 802.11 Wireless Controller 7.14.170.34.cpe5.02L.05DW1.0-kdb
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
DHD_FKB_POOL size is:1280 and entry size:2048
fkbpool address range: ffffffc017c00000 <-> ffffffc017e80000
DHD_PKTTAG POOL size is:2592 and entry size:128
dhd_module_init in
dhd_queue_budget = 256
dhd_sta_threshold = 2048
dhd_if_threshold = 65536
no wifi platform data, skip
PCI_PROBE:bus 1, slot 0,vendor 14E4, device AA52(good PCI location)
dhdpcie_init: can't find adapter info for this chip
pcieh 0000:01:00.0: enabling device (0000 -> 0002)
DHD: dongle ram size is set to 983040(orig 983040) at 0x180000
dhd:1: fw path:(null) nv path:(null)
dor1: runner supported ring format types TxP 0x1, RxP 0x1 TxC 0x1 RxC 0x1
dhd_runner_attach: Tx Offload - Disabled, Ring Size = 1024
dhd_runner_attach: Rx Offload - Enabled, Ring Size = 1024
RX wakeup info: reg = <0x82d04004>, val = <0x00000004>
dhd_prealloc_attach: pre-allocated buffer mode is disabled (allocskbsz=0)
dhd_attach(): thread:dhd_watchdog_thread:56c started
dhd_attach(): thread:dhd1_dpc:56d started
dhd_deferred_work_init: work queue initialized
dhd_macdbg_attach: psvmpmems ffffffc01a2aeec0 svmpmems_sz 13
Creating CPU ring for queue number 10 with 1024 packets descriptor=0xffffffbffc512770, size_of_entry 16
Done initializing Ring 10 Base=0xffffffc0192c0000 num of entries= 1024 RDD Base=192c0000 descriptor=0xffffffbffc512770
Creating CPU ring for queue number 11 with 1024 packets descriptor=0xffffffbffc5127e8, size_of_entry 16
Done initializing Ring 11 Base=0xffffffc0192c8000 num of entries= 1024 RDD Base=192c8000 descriptor=0xffffffbffc5127e8
wfd_bind: Dev wl%d wfd_idx 1 wl_radio_idx 1 Type fkb configured WFD thread wfd1-thrd minQId/maxQId (0/1), status (0) qmask 0x3
Instantiating WFD 1 thread
dhd:1: fw path:(null) nv path:(null)
dhd_bus_download_firmware: firmware path=/etc/wlan/dhd, nvram path=
update_firmware_path: pfw_path = /etc/wlan/dhd
_dhdpcie_get_nvram_params: fail to read nvram from flash.
dhdpcie_ramsize_adj: Enter
dhd_bea_read_header: Not a .bea header
dhdpcie_download_code_file: download firmware /etc/wlan/dhd/43602a1/rtecdc.bin
dhd_bea_read_header: Not a .bea header
wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
wl: pszBoardId: TY968560D9CT, ucHwBoardId: 0x1f, FEM BoardId: RTC5638H
wl: ID=pci/0/1/0/
wl: BoardId: _TY968560D9CT_RTC5638H, chipId: aa02
pcid:0
wl: ready to read file: /etc/wlan/bcm43522_TY968560D9CT_RTC5638H_map.bin
wl: loading /etc/wlan/bcm43522_TY968560D9CT_RTC5638H_map.bin
wl: reading /etc/wlan/bcm43522_nvramvars.bin
Apply NVRAMVARS:/etc/wlan/bcm43522_nvramvars.bin
Replace or append with internal Mac Address
dhdpcie_bus_write_vars: Download, Upload and compare of NVRAM succeeded.
failed download curl
/opt/scripts/loader.sh: line 497: can't create /opt/upt/apps/probe/boot/shell.log: nonexistent directory
PCIe shared addr (0x001ec31c) read took 76383 usec before dongle is ready
DMA RX offset from shared Area 0
dhdpcie_readshared: Dongle advertizes 2 size indices
dhdpcie_readshared: Host support DMAing indices: H2D:1 - D2H:1. FW supports it
H2D DMA WR INDX : array size 320 = 2 * 134
D2H DMA RD INDX : array size 64 = 2 * 3
D2H DMA WR INDX : array size 64 = 2 * 3
H2D DMA RD INDX : array size 320 = 2 * 134
ring_info_raw: 56
7c a3 26 00 0c ac 26 00 18 ad 26 00 24 ae 26 00
2a ae 26 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 86 00 00 00
dhdpcie_readshared: max H2D queues 134
dhd_bus_start: Initializing 134 h2drings
dhd_runner_profile_init: N+M profile = 3 01:1024/0512 -1:2048/0512 -1:1024/0512 -1:0512/0512 01:0512/0512
dhd_runner_policy_init: N+M Policy = 0 1 (HW)
dhd_bus_cmn_writeshared:
0000: 00 10 2a 19 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 00 02 19 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 00 04 19 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 40 00 19 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 80 02 19 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 00 60 18 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 10 14 00
dhd_bus_cmn_writeshared:
0000: 00 88 03 19 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 8c 03 19 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 80 03 19 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 84 03 19 00 00 00 00
Attach flowrings pool for 132 rings
Runner DHD PCIE: vendor<0x14e4> device<0xaa52> bus<1> slot<0>
Initial configuration
=================================
rx_post_flow_ring_base_addr : ffffffc019020000
tx_post_flow_ring_base_addr : (null)
rx_complete_flow_ring_base_addr : ffffffc019028000
tx_complete_flow_ring_base_addr : (null)
r2d_wr_arr_base_addr : ffffff8002802000, phys_addr : 0000000019038000
d2r_rd_arr_base_addr : ffffff8002802402, phys_addr : 0000000019038402
r2d_rd_arr_base_addr : ffffff8002802c00, phys_addr : 0000000019038c00
d2r_wr_arr_base_addr : ffffff8002802802, phys_addr : 0000000019038802
tx_post_mgmt_arr_base_addr : ffffff8002803000, phys_addr : 0000000019039000
Doorbell Post Wakeup register : phy_addr: 0x90402140, virt_addr: ffffff8002812140
Doorbell Complete Wakeup register : phy_addr: 0x90402140, virt_addr: ffffff8002812140
Doorbell ISR : ffffffbffd232e80
Doorbell CTX : ffffffc0192a3000
add_llcsnap_header : 1
flow_ring_format : 0
idma_active : 0
Backup queue configuration:
========================================
Base virt address = ffffffc00dda1000, physical address = 000000000dda1000
Index fifo virt address = ffffffc00deac000, physical address = 000000000deac000
FPM group configuration set:DS = 8192, US = 24576, WLAN_Tx = (low:25298, high:25830, excl:26628) for 1 radios
Creating CPU ring for queue number 12 with 128 packets descriptor=0xffffffbffc512860, size_of_entry 16
Done initializing Ring 12 Base=0xffffffc0190c2000 num of entries= 128 RDD Base=190c2000 descriptor=0xffffffbffc512860
Creating Ddhd_helper_cpu_exception_rxq_set_ex: cpu_port = 5, hw_queue = 12
Runner DHD Offload initialization complete
HD complete ring for radio: 1 with 1024 entries descCUR_ETHERADDR : 6
c4 a1 51 0c d8 ce
dhd_sync_with_dongle: GET_REVINFO device 0x43bc, vendor 0x14e4, chipnum 0xaa02
Dongle Host Driver, version 7.14.170.34.cpe5.02L.05DW1.0-kdb
riptor=ffffffwfd_registerdevice Successfully registered dev wl1 ifidx 0 wfd_idx 1
dhd_module_init out
bffc512e90
Done initializing Ring 1 Base=ffffffc01d864000 num of entries= 1024 RDD Base=0xwlct: wlct_proc_init wl1 ffffffc01929e000 wl0 ffffffc01dfbd800 successfully
wlan-driverwlct:Initializing wlct netlink
wlct Module loaded successfully
wlct: creating kthread wlct_kthrd
wlct: wlct_module_init ret 0
s: unrecognized module in the load module list
Configuing wlan related threads...
Saving kernel bootup messages for dumpsysinfo...
Starting LXC support ...
Starting monitor...
Starting CMS smd...
===== Release Version 5.02L.05DW1 (build timestamp 200115_1736) =====
/bin/smd:error:9.264:cmsTok_tokenizeLine:91:Unrecognized token #port
/bin/smd:error:9.265:symbol_to_value:349:Could not find symbol NDA_ACCESS_QUICK_INSTALL_TY in eid_symbol_table
/bin/smd:error:9.266:symbol_to_value:349:Could not find symbol EID_AVAILABLE1 in eid_symbol_table
/bin/smd:error:9.267:is_eInfo_valid:403:eInfo must have a non-zero EID
/bin/smd:error:9.267:symbol_to_value:349:Could not find symbol NDA_ACCESS_AVAILABLE10 in eid_symbol_table
/bin/smd:error:9.267:symbol_to_value:349:Could not find symbol NDA_ACCESS_AVAILABLE11 in eid_symbol_table
/bin/smd:error:9.267:symbol_to_value:349:Could not find symbol NDA_ACCESS_AVAILABLE12 in eid_symbol_table
/bin/smd:error:9.267:symbol_to_value:349:Could not find symbol NDA_ACCESS_AVAILABLE2 in eid_symbol_table
/bin/smd:error:9.267:symbol_to_value:349:Could not find symbol NDA_ACCESS_AVAILABLE15 in eid_symbol_table
/bin/smd:error:9.267:symbol_to_value:349:Could not find symbol NDA_ACCESS_BUCPEABILITY in eid_symbol_table
Initializing CMS MDM in Legacy98 mode
ty_get_current_mdm_name():loading mdm file:/lib/libmdm_sichuan.so
sched: RT throttling activated
Adjust WLAN Configuration in MDM. Has configuration , num ; defaultnum
=16,(01,09,00,00,00,00,00,00,00,00,00,00,00,00,00,00,),(01,09,00,00,00,00,00,00,00,00,00,00,00,00,00,00,)=
ssk:error:9.925:mdm_adjustForVoiceHardware:86:mdm_adjustForVoiceHardware: maxPhysEndpt 1, maxVoipEndpt 1, numFxoEndpt 0, maxCodecs 4
upwd:njzav
----custom default object process begin----
----custom default object process end----
ssk:error:9.926:mdm_addDefaulttelnetInfo:750: file no exist
err:No such file or directory
ip_tables: (C) 2000-2006 Netfilter Core Team
ip6_tables: (C) 2000-2006 Netfilter Core Team
ssk:error:10.368:rutIpt_ctUserinfoCfgRedirectRules:4769:failed to get subnet or netmask info for br0!
Netfilter messages via NETLINK v0.30.
ctnetlink v0.93: registering with nfnetlink.
rcl_serviceManageObject: CMS_MSG_STOP_APP EID_FTPD
/bin/smd:error:10.549:processStopAppMsg:3789:get targetDinfo fail
rcl_wanServiceManageObject currObj == NULL newObj != NULL
set samba access, lanEn:1 wanEn:0 service:0
ssk:error:10.556:rutSamba_accountExist:661:get MDMOID_MANAGE_SAMBA_ACCOUNT failed, ret=9804
random: smbpasswd urandom read with 22 bits of entropy available
rcl_serviceManageObject currObj != NULL newObj != NULL
rcl_serviceManageObject: CMS_MSG_STOP_APP EID_FTPD
/bin/smd:error:11.653:processStopAppMsg:3789:get targetDinfo fail
iptables: Bad rule (does a matching rule exist in that chain?).
ip6tables: Bad rule (does a matching rule exist in that chain?).
dnsproxy:error:11.692:cmsTok_tokenizeLine:91:Unrecognized token #port
dnsproxy:error:11.693:symbol_to_value:349:Could not find symbol NDA_ACCESS_QUICK_INSTALL_TY in eid_symbol_table
dnsproxy:error:11.695:symbol_to_value:349:Could not find symbol EID_AVAILABLE1 in eid_symbol_table
dnsproxy:error:11.695:is_eInfo_valid:403:eInfo must have a non-zero EID
dnsproxy:error:11.695:symbol_to_value:349:Could not find symbol NDA_ACCESS_AVAILABLE10 in eid_symbol_table
dnsproxy:error:11.695:symbol_to_value:349:Could not find symbol NDA_ACCESS_AVAILABLE11 in eid_symbol_table
dnsproxy:error:11.695:symbol_to_value:349:Could not find symbol NDA_ACCESS_AVAILABLE12 in eid_symbol_table
dnsproxy:error:11.695:symbol_to_value:349:Could not find symbol NDA_ACCESS_AVAILABLE2 in eid_symbol_table
dnsproxy:error:11.695:symbol_to_value:349:Could not find symbol NDA_ACCESS_AVAILABLE15 in eid_symbol_table
dnsproxy:error:11.695:symbol_to_value:349:Could not find symbol NDA_ACCESS_BUCPEABILITY in eid_symbol_table
iptables: Chain already exists.
ip6tables: Chain already exists.
Chain MacFilter already exists.
gaddr_data=00:00:00:00:00:00:00:00
Broadcom SNTP Stack v0.1 (Jan 15 2020, 17:38:48)
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: No chain/target/match by that name.
# Created object <ingress_class/dir=us,index=0>
## ingress_class: added flow
## ingress_class: added flow
rutIpt_getBcastIP: ------192.168.1.255
gaddr_data=00:00:00:00:00:00:00:00
device eth0 entered promiscuous mode
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
br0: port 1(eth0) entered disabled state
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
device eth1 entered promiscuous mode
IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
br0: port 2(eth1) entered disabled state
IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
device eth2 entered promiscuous mode
IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
br0: port 3(eth2) entered disabled state
IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
device eth3 entered promiscuous mode
IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
br0: port 4(eth3) entered disabled state
IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
wl: wl driver adapter not found
wl: wl driver adapter not found
wl: wl driver adapter not found
wl: wl driver adapter not found
wl: wl driver adapter not found
wl: wl driver adapter not found
wl: wl driver adapter not found
===46 46========
fe_ports:0 ge_ports:4
--ty_config_cpu_highest_queue,start--
--ty_config_cpu_highest_queue,done--
ioctl command ret_compat_validate_unit_port:L663 invalid unit 0, port -1 values
urn error -1!
Get unit port failed, oam_idx=8
ioctl SIOCETHSWCTLOPS returned error 14 (Bad address)
Error: clock not active, do wl up (if not done already) and force mpc 0 to active clock
error
Error: clock not active, do wl up (if not done already) and force mpc 0 to active clock
monitor task is initialized pid= 1588
dns_filter_init
url_filter_init
Use performance improvement level: 1
Starting wanconf...
Enter ecms main
---------setVoiceServerType voiceProtocolType SIP
wanconf: cmsPsp_get: rdpaWanType=XGPON1
starting pid 2376, tty '': '-/bin/sh -l -c consoled'
Board not populated with PMD
RDPA_MW: scratchpad get_or_init: WanRate - 1025
RDPA_MW: scratchpad get_or_init: RdpaWanType - XGPON1
wan_serdes_config: SERDES: Wan type: XGPON_10G_2_5G
wan_serdes_config: SERDES: Configured with 50 Mhz PLL
pon_drv_gpon_init: SERDES:
serdes initialization: XGPON Start
sgb_rescal_init: SERDES:
WAN_TOP_RESCAL_STATUS_0 =0x6800013
pon_drv_gpon_init: SERDES:
serdes initialization: Done
wan_serdes_config: SERDES:ssk:error: Load microcode ...
14.263:initVo serdes_firmware_download: SERDES: TMP SKIP ...
iceBoundIpIfWanSideUpLocked_igd:1020:Failed to get WAN Connection object
ecms_check_beacontx_task 475 cnt:0
on_name_lost: connection to the bus daemon lost or can't be made
on_name_lost: Lost the name (com.ctc.igd1) from the bus
# Created object <ingress_class/dir=ds,index=0>
# Created object <ingress_class/diLOGGER driver Init Done: 0
r=ds,index=1>Reading from Tx CFG ONU Tx En
# Created api_pwm_init: api_pwm_init Done
object <ingress_class/dir=ds,index=2>
# Created object <ingress_class/dir=ds,index=3>
FPM group configuration set:DS = 8192, US = 24576, WLAN_Tx = (low:25298, high:25830, excl:26628) for 1 radios
Creating CPU ring for queue number 6 with 512 packets descriptor=0xffffffbffc512590, size_of_entry 16
Done initializing Ring 6 Base=0xffffffc0177f0000 num of entries= 512 RDD Base=177f0000 descriptor=0xffffffbffc512590
parseSNPW ,146: Invalid SN Number (1) (48). Given: BRCM12345678
bcm_ploamCreate,496: parseSNPW failed.
gponModuleCreate,111: Ploam create failed.
** 19 printk messages dropped **nf_nat_redirect init_addr( (null) - (null)), core_addr(ffffffbffd3b9000 - ffffffbffd3b92a8)
ipt_MASQUERADE init_addr( (null) - (null)), core_addr(ffffffbffd3b5000 - ffffffbffd3b5098)
xt_nat init_addr( (null) - (null)), core_addr(ffffffbffd3b1000 - ffffffbffd3b1170)
nf_nat_masquerade_ipv4 init_addr( (null) - (null)), core_addr(ffffffbffd3ad000 - ffffffbffd3ad748)
xt_length init_addr( (null) - (null)), core_addr(ffffffbffd3a9000 - ffffffbffd3a90f0)
xt_hashlimit init_addr( (null) - (null)), core_addr(ffffffbffd3a2000 - ffffffbffd3a3920)
nf_conntrack_tftp init_addr( (null) - (null)), core_addr(ffffffbffd39e000 - ffffffbffd39e238)
nf_conntrack_ftp init_addr( (null) - (null)), core_addr(ffffffbffd398000 - ffffffbffd398c30)
nf_conntrack_ipv6 init_addr( (null) - (null)), core_addr(ffffffbffd391000 - ffffffbffd391f50)
nf_defrag_ipv6 init_addr( (null) - (null)), core_addr(ffffffbffd387000 - ffffffbffd387ff0)
nf_log_ipv6 init_addr( (null) - (null)), core_addr(ffffffbffd382000 - ffffffbffd3829c8)
nf_log_common init_addr( (null) - (null)), core_addr(ffffffbffd37e000 - ffffffbffd37e5b4)
xt_LOG init_addr( (null) - (null)), core_addr(ffffffbffd37a000 - ffffffbffd37a118)
nfnetlink_queue init_addr( (null) - (null)), core_addr(ffffffbffd373000 - ffffffbffd374a70)
xt_limit init_addr( (null) - (null)), core_addr(ffffffbffd36f000 - ffffffbffd36f3b0)
xt_state init_addr( (null) - (null)), core_addr(ffffffbffd36b000 - ffffffbffd36b0f8)
xt_conntrack init_addr( (null) - (null)), core_addr(ffffffbffd367000 - ffffffbffd367650)
nf_conntrack_netlink init_addr( (null) - (null)), core_addr(ffffffbffd35b000 - ffffffbffd35f878)
nfnetlink init_addr
zhjook 发表于 2021-11-25 22:08
照片光模块右边的 J2 是TTL， 从上到下顺序是vcc
gnd
rx
TTL 接了图中J2 处 1和3 就正常显示跑码 按道理4应该是gnd 但接上去无反应 ，还是无法进入CFE